Tenda W300A
| bgn (N300) | |
|---|---|
| 300Mbps Wireless N PoE Access Point | |
|
| |
| Homepage | Product page |
| InfoDepot Wiki | Tenda W300A |
| 3rd Party Firmware | |
| dd-wrt | Status Unknown |
| OpenWrt | Status Unknown |
| Tomato any flavor | Incompatible |
| Platform | |
| Brand • Model • Rev | Tenda W300A |
| FCC ID | none specified |
| Type | access point |
| CPU1 | Ralink RT2880 |
| CPU1 Type | MIPS 4KEc |
| CPU1 Speed | 266 MHz |
| Flash1 Chip | KH KH29LV320DBTC-70G |
| Flash1 Size | 4 MiB 4,194,304 B <br />32,768 Kib <br />4,096 KiB <br />32 Mib <br />0.00391 GiB <br /> (Parallel) |
| RAM1 Size | 16 MiB 16,777,216 B <br />131,072 Kib <br />16,384 KiB <br />128 Mib <br />0.0156 GiB <br /> |
| RAM1 Chip | SK hynix HY57V641620FTP-7 x 2 |
| ETH chip1 | Ralink RT2880 |
| ETH chip2 | Vitesse VSC8601XKN |
| Ethernet Port Count | 1-1GbE-LAN |
| Wired Standard | IEEE 802.3/3u/3ab |
|
802dot11 OUI: none specified | |
| boot_wait | 4s |
| Stock bootloader | U-Boot |
| Expansion IF types | none specified |
| PoE | 802.3af, standard |
| Power | ? VDC, ? A |
|
| |
|
| |
| Other | |
|
Default IP address: 192.168.0.254 | |
| Physical | |
| LEDs/Color | 3x green, 1x red/green |
| Radio 1 | |
| Chip1 | Ralink RT2880 |
| Chip2 | Ralink RT2820 |
| Wireless interface OUI | none specified |
| Antenna Connector Type | none specified |
| MIMO status | 2x3:2 |
| Wireless Standard | IEEE 802.11b/g/n |
| 802.11n | up to 300 Mbps |
| 802.11g | up to 54 Mbps |
| 802.11b | up to 11 Mbps |
| WiFi Operating Frequency | 2.4 GHz |
For a list of all currently documented Ralink chipsets with specifications, see Ralink.
For a list of all currently documented Microsemi (Vitesse) chipsets with specifications, see Microsemi.
For a list of all currently documented Tenda devices with specifications, see Tenda.
- • 300 Mbps - 2SS 2.4GHz 802.11n (40MHz chan.) = N300 class
Overview
The default SSID may be Tenda.
Links of Interest
On the OpenWrt wiki
On SpeedGuide.net
JTAG-Serial Info
Serial
Serial Pinouts
On the other side of the PCB there are 4 test points:
- TP1 GND
- TP2 ? (probably Vcc)
- TP3,4 serial console
The serial interface is 3.3V TTL levels (need USB cable and/or level converter to connect to a PC). Settings are 57k6 8N1 no flow control.
boot log
| boot log |
|---|
U-Boot 1.1.3 (Feb 22 2008 - 16:48:17)
Board: RT2880 DRAM: 16 MB
twe0 set to <NULL>
toe0 set to <NULL>
flash_protect ON: from 0xBF000000 to 0xBF02479B
protect on 0
protect on 1
protect on 2
flash_protect ON: from 0xBF030000 to 0xBF03FFFF
protect on 3
============================================
ASIC -VerB/C (MAC to 100PHY Mode)
DRAM COMPONENT=64Mbits
DRAM BUS=32BIT
Total memory = 16Mbytes
Date:Feb 22 2008 Time:16:48:17
============================================
D-CACHE set to 4 way
I-CACHE set to 4 way
##### The CPU freq = 266 MHZ ####
SDRAM bus set to 32 bit
SDRAM size =16 Mbytes
Please choose the operation:
1: Load system code to SDRAM via TFTP.
2: Load system code then write to Flash via TFTP.
3: Boot system code via Flash (default).
4: Entr boot command line interface.
5: Load ucos code to SDRAM via TFTP.
3: System Boot system code via Flash.
## Booting image at bf050000 ...
Image Name: Linux Kernel Image
Created: 2008-10-29 18:46:32 UTC
System Control Status = 0x02910084
Image Type: MIPS Linux Kernel Image (lzma compressed)
Data Size: 2447621 Bytes = 2.3 MB
Load Address: 88000000
Entry Point: 88190040
Verifying Checksum ... OK
Uncompressing Kernel Image ... OK
No initrd
## Transferring control to Linux (at address 88190040) ...
## Giving linux memsize in MB, 16
Starting kernel ...
THIS IS ASIC
ramsize = 16 MBytes
rambase not set, set to default (0x08000000)
MEMORY DESCRIPTOR dump:
[0,883d0b80]: base<08000000> size<01000000> type<Free RAM memory>
The CPU feqenuce set to 266 MHz
CPU revision is: 0001906c
icache: sets:256, ways:4, linesz:16 ,total:16384, waybit:12, flags:0x0
dcache: sets:256, ways:4, linesz:16 ,total:16384, waybit:12, flags:0x0
i waysize = 4096, d waysize = 4096, i sets= 256, d sets=256
Primary instruction cache 16kB, physically tagged, 4-way, linesize 16 bytes.
Primary data cache 16kB, 4-way, linesize 16 bytes.
[setup_scache]:1032
Linux version 2.4.30 (root@linux-r3ht) (gcc version 3.3.6) #1 Thu Oct 30 02:42:35 CST 2008
Determined physical RAM map:
memory: 01000000 @ 08000000 (usable)
Initial ramdisk at: 0x881c2000 (1855488 bytes)
On node 0 totalpages: 36864
zone(0): 36864 pages.
zone(1): 0 pages.
zone(2): 0 pages.
Kernel command line: console=ttyS1,57600n8 root=/dev/ram0
cause = e080804c, status = 1000ff00
calculating r4koff... 0028b0aa(2666666)
CPU frequency 266.67 MHz
Using 133.333 MHz high precision timer.
Calibrating delay loop... 266.24 BogoMIPS
Memory: 10872k/16384k available (1585k kernel code, 5512k reserved, 1912k data, 92k init, 0k highmem)
Dentry cache hash table entries: 32768 (order: 6, 262144 bytes)
Inode cache hash table entries: 16384 (order: 5, 131072 bytes)
Mount cache hash table entries: 512 (order: 0, 4096 bytes)
Buffer cache hash table entries: 8192 (order: 3, 32768 bytes)
Page-cache hash table entries: 65536 (order: 6, 262144 bytes)
Checking for 'wait' instruction... unavailable.
POSIX conformance testing by UNIFIX
pci.c pcibios_init():840
BAR0 at slot 0 = 8
pci.c pcibios_fixup_resources():640
bus = 0, dev = 0, fun = 0
dev= 0x88564c00
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
Starting kswapd
devfs: v1.12c (20020818) Richard Gooch (rgooch@atnf.csiro.au)
devfs: boot_options: 0x1
squashfs: version 3.1 (2006/08/19) Phillip Lougher
pty: 256 Unix98 ptys configured
Ralink RT2880 gpio driver start init
SetGPIOType: id [12] type[0]
SetGPIOType: id [11] type[0]
SetGPIOType: id [13] type[1]
SetGPIOType: id [0] type[1]
Ralink RT2880 gpio driver initialized
spidrv_major = 217
Serial driver version 5.05c (2001-07-08) with MANY_PORTS SHARE_IRQ SERIAL_PCI enabled
ttyS00 at 0x300500 (irq = 9) is a 16550A
ttyS01 at 0x300c00 (irq = 8) is a 16550A
HDLC line discipline: version $Revision: 1.1.1.1 $, maxframe=4096
N_HDLC line discipline registered.
RAMDISK driver initialized: 16 RAM disks of 8192K size 1024 blocksize
GDMA1_MAC_ADRH -- : 0x00000000
GDMA1_MAC_ADRL -- : 0x00000000
Ralink APSoC Ethernet Driver Initilization. v1.60 256 rx/tx descriptors allocated, mtu = 1600!
GDMA1_MAC_ADRH -- : 0x0000b848
GDMA1_MAC_ADRL -- : 0x000c4328
PROC INIT OK!
rdm_major = 254
FLASH_API: MAN_ID=C2 DEV_ID=22A8 SIZE=4MB
physmap flash device: 400000 at bfc00000
Amd/Fujitsu Extended Query Table v1.1 at 0x0040
number of CFI chips: 1
Region0: SectorSize=0x2000 SectorNum=8
Region1: SectorSize=0x10000 SectorNum=63
cfi_cmdset_0002: Using word write method.
cfi_cmdset_0002: Disabling fast programming due to code brokenness.
Using physmap partition definition
Creating 4 MTD partitions on "RT2880 SOC Physically mapped flash":
0x00000000-0x00030000 : "Bootloader"
mtd: Giving out device 0 to Bootloader
0x00030000-0x00040000 : "Config "
mtd: Giving out device 1 to Config
0x00040000-0x00050000 : "Factory"
mtd: Giving out device 2 to Factory
0x00050000-0x00400000 : "Kernel"
mtd: Giving out device 3 to Kernel
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP, IGMP
IP: routing cache hash table of 1024 buckets, 8Kbytes
TCP: Hash tables configured (established 16384 bind 32768)
GRE over IPv4 tunneling driver
Linux IP multicast router 0.06 plus PIM-SM
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
NET4: Ethernet Bridge 008 for NET4.0
802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
All bugs added by David S. Miller <davem@redhat.com>
RAMDISK: Compressed image found at block 0
Freeing initrd memory: 1812k freed
VFS: Mounted root (squashfs filesystem) readonly.
Mounted devfs on /dev
Freeing prom memory: 0kb freed
Freeing unused kernel memory: 92k freed
console started
trying to start /sbin/init
Algorithmics/MIPS FPU Emulator v1.5
init started: BusyBox v1.8.2 (2008-10-30 02:36:26 CST)
starting pid 10, tty '': '/etc_ro/rcS'''
mount: mounting devpts: called with bogus options
none on /sys failed: No such device
mount: mounting none on /proc/bus/usb failed: No such file or directory
starting pid 16, tty '/dev/console': '/bin/sh'
BusyBox v1.8.2 (2008-10-30 02:36:26 CST) built-in shell (ash)
Enter 'help' for a list of built-in commands.
#
Yes:
****** WeLoveLinux ******
Welcome to ...
kernel reg pid 14 success .
httpd Reg gpio hook success .
insmod rt2860v2_ap
2860 version : 1.9.0.0 (Oct 30 2008)
=== pAd = c0507000, size = 484224 ===
<-- RTMPAllocAdapterBlock, Status=0
ralink_init make_wireless_config rt2860
ifconfig ra0 0.0.0.0
RX DESC a8c4d000 size = 2048
<-- RTMPAllocTxRxRingMemory, Status=0
1. Phy Mode = 9
2. Phy Mode = 9
3. Phy Mode = 9
...
|
ifconfig
# ifconfig lo
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:0 (0.0 B) TX bytes:0 (0.0 B)
u-Boot
For TFTP from u-Boot the AP has to bo connected to a 10/100M switch (does not work neither on a 10/100/1000M switch nor on a 10M hub).
For FW recovery use option 2 ("Load system code then write to Flash via TFTP.") to download the original FW image (currently U300ARAEN_2.4.15.bin from U300A_EN_2.4.15.zip).
| System info • >> |
|---|
=====Version=====
# cat /proc/version
Linux version 2.4.30 (root@linux-r3ht) (gcc version 3.3.6) #1 Thu Oct 30 02:42:35 CST 2008
=====CPU info=====
# cat /proc/cpuinfo
system type : Palmchip Surfboard
processor : 0
cpu model : unknown V6.12
BogoMIPS : 266.24
wait instruction : no
microsecond timers : yes
tlb_entries : 16
extra interrupt vector : yes
hardware watchpoint : no
VCED exceptions : not available
VCEI exceptions : not available
=====Meminfo=====
# cat /proc/meminfo
total: used: free: shared: buffers: cached:
Mem: 13082624 10506240 2576384 0 897024 3710976
Swap: 0 0 0
MemTotal: 12776 kB
MemFree: 2516 kB
MemShared: 0 kB
Buffers: 876 kB
Cached: 3624 kB
SwapCached: 0 kB
Active: 2464 kB
Inactive: 2044 kB
HighTotal: 0 kB
HighFree: 0 kB
LowTotal: 12776 kB
LowFree: 2516 kB
SwapTotal: 0 kB
SwapFree: 0 kB
=====MTD=====
# cat /proc/mtd
dev: size erasesize name
mtd0: 00030000 00010000 "Bootloader"
mtd1: 00010000 00010000 "Config "
mtd2: 00010000 00010000 "Factory"
mtd3: 003b0000 00010000 "Kernel"
=====Interrupts=====
# cat /proc/interrupts
CPU0
3: 1269 Surfboard eth2
4: 12078 Surfboard ra0
6: 53928 Surfboard timer
8: 313 Surfboard serial
ERR: 0
=====PS=====
# ps
PID Uid VSZ Stat Command
1 0 1608 S init
2 0 SW [keventd]
3 0 SWN [ksoftirqd_CPU0]
4 0 SW [kswapd]
5 0 SW [bdflush]
6 0 SW [kupdated]
7 0 SW [mtdblockd]
14 0 1992 S httpd
16 0 1616 S /bin/sh
19 0 SW [rtmpWscHandle]
116 0 1608 S udhcpc -i br0 -h W300A -s /etc_ro/udhcpc.script -p /v
125 0 1992 S httpd
126 0 1992 S httpd
127 0 748 S wins W300A 192.168.2.90
134 0 1608 R ps
=====PCI=====
# cat /proc/pci
PCI devices found:
Bus 0, device 0, function 0:
Class 0080: PCI device 1814:0802 (rev 1).
Master Capable. Latency=255.
Prefetchable 32 bit memory at 0x0 [0xfffffff].
# cat /proc/bus/pci/devices
0000 18140802 0 00000008 00000000 00000000 00000000 00000000 00000000 00000000 1000000000000000 00000000 00000000 00000000 00000000 00000000
|
- Tenda
- Embedded system/access point
- Embedded System Ralink
- Embedded System RT2880
- Ralink
- Embedded System MIPS 4KEc
- Embedded System
- Embedded System VSC8601XKN
- Embedded System Vitesse
- Vitesse
- Embedded System RT2820
- Has Mimo Status
- Embedded System IEEE 802.11b/g/n
- Single-Radio Wireless Embedded System
- Wireless Embedded System
- Single-Band
- English Documentation