WAVLINK WL-WN570HA2

multiple revisions of this device, use caution

abgn+ac
AC1200 Dual Band Outdoor Access Point Outdoor Long Range Wi-Fi Extender
Homepage	Product page
3rd Party Firmware
dd-wrt	Status Unknown
OpenWrt	Supported
Tomato any flavor	Incompatible
Gargoyle	Status Unknown
Platform
Brand • Model • Rev	WAVLINK WL-WN570HA2
FCC ID	none specified
Type	access point
CPU1 Y	MediaTek MT7628DAN
CPU1 Type	MIPS 24KEc
CPU1 Speed	580 MHz
Flash1 Chip	Brand? Model?
Flash1 Size	16 MiB 16,777,216 B <br />131,072 Kib <br />16,384 KiB <br />128 Mib <br />0.0156 GiB <br />
RAM1 Size	64 MiB 67,108,864 B <br />524,288 Kib <br />65,536 KiB <br />512 Mib <br />0.0625 GiB <br />
RAM1 Chip	Brand? Model?
ETH chip1	MediaTek MT7628DAN
Ethernet Port Count	1-100MbE-LAN
Wired Standard	IEEE 802.3i/3u
802dot11 OUI: none specified
Stock bootloader	U-Boot
Expansion IF types	none specified
PoE	Passive
Power	54 VDC, 0.3 A
Serial Port (UART)	yes, 3.3V TTL, (57600 8N1)
Other
3rd Party Firmware Support	OpenWrt • (List | Dev | DLs)
Radio 1
Chip1	MediaTek MT7628DAN
Wireless interface OUI	none specified
Antenna Connector Type	none specified
MIMO status	2x2:2
Wireless Standard	IEEE 802.11b/g/n
802.11n	up to 300 Mbps
802.11g	up to 54 Mbps
802.11b	up to 11 Mbps
WiFi Operating Frequency	2.4 GHz
Radio 2
Chip1	MediaTek MT7613BEN
Wireless interface OUI	none specified
Antenna Connector Type	none specified
MIMO status	2x2:2
Wireless Standard	IEEE 802.11a/n/ac
802.11ac	up to 867 Mbps
802.11n	up to 300 Mbps
802.11a	up to 54 Mbps
WiFi Operating Frequency	5 GHz
CPU1 brand Radio1 chip1 brand Radio2 chip1 brand WAVLINK WL-WN570HA1 MediaTek MediaTek MediaTek WAVLINK WL-WN570HA2 MediaTek MediaTek MediaTek

For a list of all currently documented MediaTek chipsets with specifications, see MediaTek.

For a list of all currently documented WAVLINK devices with specifications, see WAVLINK.

Flashing

Flashing OpenWrt

On the OpenWrt ToH (techdata entry)

Target: ramips
Subtarget: mt76x8
Package architecture: mipsel_24kc
Supported Since Commit
Support started version: 25.12.0
Current supported version: 25.12.2

Unsupported Functions:
DFS
WLAN Hardware: MediaTek MT7628DAN, MediaTek MT7613BEN
Installation method(s):
see git-commit
Recovery method(s):
see git-commit

git • >>

ramips: add support for Wavlink WL-WN570HA2 The Wavlink Aerial HD3 (WL-WN570HA2) is an AC1200 dual-band outdoor access point. It supports 802.3AT/AF PoE and is IP67 waterproof. It is based on the MediaTek MT7628DAN SoC and MT7613BEN WiFi 5 chip. This model uses the 100Mbit LAN and 2.4Ghz WiFi elements of the MT7628 and the 5Ghz WiFi of the MT7613. Specification: - SoC: MediaTek MT7628DAN (1C/1T) @ 580MHz - RAM: 64MB DDR2 (integrated in SoC) - FLASH: 16MB SPI NOR (Fudan FM25Q128A) - Ethernet: 1x 10/100Mbps - WiFi: 2.4/5 GHz 2T2R - 2.4GHz MediaTek MT7628DAN bgn - 5GHz MediaTek MT7613BEN nac - Antennas: 2x detachable, dual-band 7dBi with RP-SMA connectors. - USB: none - BTN: Reset - LED: 6 total: power; WAN/LAN; WiFi; WiFi low; WiFi med; Wifi high - UART: surface-mount on PCB. Pins are marked via silkscreen. pin1 (square pad, towards Ethernet)=Vcc, pin2=RX, pin3=TX, pin4=GND. Settings: 57600/8N1. NOTE: The TX & RX silkscreens were reversed on my test unit. Installation: 1) This device requires a HTTP recovery procedure to do an initial load of OpenWRT. You will need: a. A web browser (private window recommended) b. Configure an Ethernet interface to 192.168.1.x/24; don't use .1 c. Connect a cable between the computer and the Wavlink's PoE injector. 2) Put the Wavlink in HTTP recovery mode. a. Do this by pressing and holding the reset button on the bottom while powering the unit on. b. As soon as all 6 LEDs light up blue (roughly 2-3 seconds), release the button. c. The LEDs should all remain lit, indicating it's in HTTP recovery. 3) Point the browser at http://192.168.1.1/index.html 4) Click "Choose File" and select the OpenWRT sysupgrade image. 5) Click the "Update Firmware" button and wait while the unit flashes the image and reboots. 6) When the system comes back up fully, only the power LED will be lit. Wait an extra minute then you should be able to reach OpenWRT on http://192.168.1.1 5) Log into LuCI as root; there is no password. Revert to the OEM Firmware: -------------------------- * U-boot HTTP: Follow the HTTP recovery steps, and use a firmware image downloaded from Wavlink.