Xiaomi MiWiFi 3G

multiple revisions of this device, use caution

abgn+ac (AC1200)
Xiaomi MiWiFi 3G
Homepage	Product page (CN)
3rd Party Firmware
dd-wrt	Status Unknown
OpenWrt	Supported
Tomato any flavor	Incompatible
Gargoyle	Status Unknown
Platform
Brand • Model • Rev	Xiaomi MiWiFi 3G v1
FCC ID	none specified
Type	wireless router
Series	MiWiFi
CPU1	MediaTek MT7621AT
CPU1 Type	MIPS 1004Kc
CPU1 Speed	880 MHz ( 2 cores ) 16-bit
Flash1 Chip	ESMT F59L1G81LA-25T
Flash1 Size	128 MiB134,217,728 B <br />1,048,576 Kib <br />131,072 KiB <br />1,024 Mib <br />0.125 GiB <br /> (NAND)
RAM1 Size	256 MiB268,435,456 B <br />2,097,152 Kib <br />262,144 KiB <br />2,048 Mib <br />0.25 GiB <br />
RAM1 Chip	Nanya NT5CC128M16IP-DI
ETH chip1	MediaTek MT7621AT
Switch	MediaTek MT7621AT
Ethernet Port Count	1-1GbE-WAN 2-1GbE-LAN
Wired Standard	IEEE 802.3i/3u/3ab
802dot11 OUI: 34:CE:00 (1 E, 1 W) Ethernet OUI: 34:CE:00 (1 E, 1 W)
Stock bootloader	U-Boot
Stock FW OS	Linux 3.10.14
Expansion IF types	USB 3.0
USB ports	1
USB Hub Compatible	Untested
Power	12 VDC, 1.5 A
Connector type	barrel
Serial Port (UART)	yes, 4-pad header, J4
Other
Default SSID: Xiaomi_XXXX (19 addl. devices) , Xiaomi_XXXX_5G (16 addl. devices) Default IP address: 192.168.31.1 the IP 192.168.31.1 is used by 20 additional devices of which 19 are Xiaomi devices
3rd Party Firmware Support	OpenWrt • (List | Dev | DLs)
Retail
Availability	End of Life
(Est.) release date	March 2017
Country of manuf	China
Radio 1
Chip1	MediaTek MT7603EN
Wireless interface OUI	34:CE:00
Antenna Connector Type	U.FL
MIMO status	2x2:2
Wireless Standard	IEEE 802.11b/g/n
802.11n	up to 300 Mbps
802.11g	up to 54 Mbps
802.11b	up to 11 Mbps
WiFi Operating Frequency	2.4 GHz
Radio 2
Chip1	MediaTek MT7612EN
Wireless interface OUI	34:CE:00
Antenna Connector Type	U.FL
MIMO status	2x2:2
Wireless Standard	IEEE 802.11a/n/ac
802.11ac	up to 867 Mbps
802.11n	up to 300 Mbps
802.11a	up to 54 Mbps
WiFi Operating Frequency	5 GHz
CPU1 brand Radio1 chip1 brand Radio2 chip1 brand Xiaomi MiWiFi (R1D) Broadcom Broadcom Broadcom Xiaomi MiWiFi (R2D) Broadcom Broadcom Broadcom Xiaomi MiWiFi 3A MediaTek MediaTek MediaTek Xiaomi MiWiFi 3C MediaTek MediaTek Xiaomi MiWiFi 3G MediaTek MediaTek MediaTek Xiaomi MiWiFi 3G v2 MediaTek MediaTek MediaTek Xiaomi MiWiFi 4 MediaTek MediaTek MediaTek Xiaomi MiWiFi 4Q Qualcomm Atheros Qualcomm Atheros Xiaomi MiWiFi Nano (R1CL) MediaTek MediaTek

For a list of all currently documented MediaTek chipsets with specifications, see MediaTek.

For a list of all currently documented Xiaomi device with specifications, see Xiaomi.

• 867 Mbps - 2SS 5GHz 802.11ac (80MHz chan.),

• 300 Mbps - 2SS 2.4GHz 802.11n (40MHz chan.) = AC1200 class

Links of Interest

• Review on KoolShare forums
• Review on Mysku (RU)

Forum threads

• On 4pda forums (RU)

Third party firmware

• On OpenWrt wiki
• On LEDE Project forums ('Dev FW')
• Commit to LEDE (/ now OpenWrt) git adding support for this device

Flashing

Flashing OpenWrt

On the OpenWrt ToH (techdata entry)
On the OpenWrt Wiki
On the OpenWrt Forum
On the OpenWrt Forum
On the OpenWrt Forum
OpenWrt Target: ramips
OpenWrt Subtarget: mt7621
OpenWrt Package architecture: mipsel_24kc
Support started version: 18.06.0
Current supported version: 23.05.5
Comment:
2.4G is unstable

Please insert instructions here

JTAG-Serial Info

Serial

Boot log

=================================================================== MT7621 stage1 code 10:33:11 (ASIC) CPU=50000000 HZ BUS=12500000 HZ ================================================================== Change MPLL source from XTAL to CR... do MEMPLL setting.. MEMPLL Config : 0x11100000 3PLL mode + External loopback === XTAL-40Mhz === DDR-1200Mhz === PLL2 FB_DL: 0x12, 1/0 = 759/265 49000000 PLL3 FB_DL: 0x12, 1/0 = 775/249 49000000 PLL4 FB_DL: 0x16, 1/0 = 548/476 59000000 do DDR setting..[00320381] Apply DDR3 Setting...(use customer AC) 0 8 16 24 32 40 48 56 64 72 80 88 96 104 112 120 -------------------------------------------------------------------------------- 0000:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0001:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0002:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0003:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0004:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0005:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0006:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0007:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0008:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0009:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 000A:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 000B:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 000C:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 000D:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 000E:| 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 000F:| 0 0 0 0 1 1 1 1 1 1 1 1 1 1 0 0 0010:| 1 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0011:| 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0012:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0013:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0014:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0015:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0016:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0017:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0018:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0019:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 001A:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 001B:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 001C:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 001D:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 001E:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 001F:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 rank 0 coarse = 15 rank 0 fine = 72 B:| 0 0 0 0 0 0 0 0 0 0 1 1 1 0 0 0 opt_dle value:11 DRAMC_R0DELDLY[018]=0000201F ================================================================== RX DQS perbit delay software calibration ================================================================== 1.0-15 bit dq delay value ================================================================== bit| 0 1 2 3 4 5 6 7 8 9 -------------------------------------- 0 | 11 7 9 9 7 8 9 7 5 7 10 | 7 9 10 12 9 10 -------------------------------------- ================================================================== 2.dqs window x=pass dqs delay value (min~max)center y=0-7bit DQ of every group input delay:DQS0 =31 DQS1 = 32 ================================================================== bit DQS0 bit DQS1 0 (2~61)31 8 (1~58)29 1 (2~59)30 9 (1~60)30 2 (1~60)30 10 (1~60)30 3 (1~60)30 11 (1~59)30 4 (1~60)30 12 (1~64)32 5 (1~61)31 13 (1~61)31 6 (1~60)30 14 (2~63)32 7 (1~62)31 15 (1~61)31 ================================================================== 3.dq delay value last ================================================================== bit| 0 1 2 3 4 5 6 7 8 9 -------------------------------------- 0 | 11 8 10 10 8 8 10 7 8 9 10 | 9 11 10 13 9 11 ================================================================== ================================================================== TX perbyte calibration ================================================================== DQS loop = 15, cmp_err_1 = ffff0000 dqs_perbyte_dly.last_dqsdly_pass[0]=15, finish count=1 dqs_perbyte_dly.last_dqsdly_pass[1]=15, finish count=2 DQ loop=15, cmp_err_1 = ffff0080 dqs_perbyte_dly.last_dqdly_pass[1]=15, finish count=1 DQ loop=14, cmp_err_1 = ffff0000 dqs_perbyte_dly.last_dqdly_pass[0]=14, finish count=2 byte:0, (DQS,DQ)=(8,8) byte:1, (DQS,DQ)=(8,8) 20,data:88 [EMI] DRAMC calibration passed =================================================================== MT7621 stage1 code done CPU=50000000 HZ BUS=12500000 HZ =================================================================== U-Boot 1.1.3 (Apr 17 2017 - 17:00:02) Board: Ralink APSoC DRAM: 256 MB Power on memory test. Memory size= 256 MB...OK! relocate_code Pointer at: 8ffac000 Config XHCI 40M PLL Allocate 16 byte aligned buffer: 8ffdffd0 Enable NFI Clock # MTK NAND # : Use HW ECC NAND ID [C8 D1 80 95 42] Device not found, ID: c8d1 Not Support this Device! chip_mode=00000001 Support this Device in MTK table! c8d1 select_chip [NAND]select ecc bit:4, sparesize :64 spare_per_sector=16 Signature matched and data read! load_fact_bbt success 1023 load fact bbt success [mtk_nand] probe successfully! mtd->writesize=2 GiB mtd->oobsize=64, mtd->erasesize=131072 devinfo.iowidth=8 ============================================ Ralink UBoot Version: 5.0.0.0 -------------------------------------------- ASIC MT7621A DualCore (MAC to MT7530 Mode) DRAM_CONF_FROM: Auto-Detection DRAM_TYPE: DDR3 DRAM bus: 16 bit Xtal Mode=5 OCP Ratio=1/4 Flash component: NAND Flash Date:Apr 17 2017 Time:17:00:02 ============================================ icache: sets:256, ways:4, linesz:32 ,total:32768 dcache: sets:256, ways:4, linesz:32 ,total:32768 ##### The CPU freq = 880 MHZ #### estimate memory size =256 Mbytes #Reset_MT7530 set LAN/WAN LWLLL Please choose the operation: 1: Load system code to SDRAM via TFTP. 2: Load system code then write to Flash via TFTP. 3: Boot system code via Flash (default). 4: Entr boot command line interface. 7: Load Boot Loader code then write to Flash via Serial. 9: Load Boot Loader code then write to Flash via TFTP. 0 Booting System 1 ..Erasing NAND Flash... ranand_erase: start:80000, len:20000 .Writing to NAND Flash... done 3: System Boot system code via Flash. ## Booting image at bc200000 ... Image Name: MIPS OpenWrt Linux-3.10.14 Image Type: MIPS Linux Kernel Image (lzma compressed) Data Size: 3433332 Bytes = 3.3 MB Load Address: 80001000 Entry Point: 80468ce0 ........ Verifying Checksum ... OK Uncompressing Kernel Image ... OK commandline uart_en=1 factory_mode=0 usb_u3=0 No initrd ## Transferring control to Linux (at address 80468ce0) ... ## Giving linux memsize in MB, 256 Starting kernel ... LINUX started... THIS IS ASIC SDK 5.0.S.0 [ 0.000000] Initializing cgroup subsys cpuset [ 0.000000] Linux version 3.10.14 (jenkins@JenkinsServer) (gcc version 4.8.5 (crosstool-NG crosstool-ng-1.22.0) ) #1 SMP Mon Apr 17 17:08:55 CST 2017 [ 0.000000] [ 0.000000] The CPU feqenuce set to 880 MHz [ 0.000000] GCMP present [ 0.000000] CPU0 revision is: 0001992f (MIPS 1004Kc) [ 0.000000] Software DMA cache coherency [ 0.000000] Determined physical RAM map: [ 0.000000] memory: 10000000 @ 00000000 (usable) [ 0.000000] Initrd not found or empty - disabling initrd [ 0.000000] Zone ranges: [ 0.000000] DMA [mem 0x00000000-0x0bffffff] [ 0.000000] Normal [mem 0x0c000000-0x0fffffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x00000000-0x0fffffff] [ 0.000000] Detected 3 available secondary CPU(s) [ 0.000000] Primary instruction cache 32kB, 4-way, VIPT, linesize 32 bytes. [ 0.000000] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes [ 0.000000] MIPS secondary cache 256kB, 8-way, linesize 32 bytes. [ 0.000000] PERCPU: Embedded 7 pages/cpu @8c204000 s6848 r8192 d13632 u32768 [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 65024 [ 0.000000] Kernel command line: console=ttyS1,115200n8 root=/dev/mtdblock5 uart_en=1 factory_mode=0 usb_u3=0 [ 0.000000] PID hash table entries: 1024 (order: 0, 4096 bytes) [ 0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes) [ 0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes) [ 0.000000] Writing ErrCtl register=00000410 [ 0.000000] Readback ErrCtl register=00000410 [ 0.000000] allocated 524288 bytes of page_cgroup [ 0.000000] please try 'cgroup_disable=memory' option if you don't want memory cgroups [ 0.000000] Memory: 251564k/262144k available (4561k kernel code, 10580k reserved, 1208k data, 1584k init, 0k highmem) [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 [ 0.000000] Hierarchical RCU implementation. [ 0.000000] NR_IRQS:128 [ 0.000000] console [ttyS1] enabled [ 0.130000] Calibrating delay loop... 563.20 BogoMIPS (lpj=2816000) [ 0.190000] pid_max: default: 32768 minimum: 301 [ 0.190000] Mount-cache hash table entries: 512 [ 0.200000] Initializing cgroup subsys memory [ 0.200000] launch: starting cpu1 [ 0.200000] launch: cpu1 gone! [ 0.200000] CPU1 revision is: 0001992f (MIPS 1004Kc) [ 0.200000] Primary instruction cache 32kB, 4-way, VIPT, linesize 32 bytes. [ 0.200000] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes [ 0.200000] MIPS secondary cache 256kB, 8-way, linesize 32 bytes. [ 0.260000] Synchronize counters for CPU 1: done. [ 0.270000] launch: starting cpu2 [ 0.270000] launch: cpu2 gone! [ 0.270000] CPU2 revision is: 0001992f (MIPS 1004Kc) [ 0.270000] Primary instruction cache 32kB, 4-way, VIPT, linesize 32 bytes. [ 0.270000] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes [ 0.270000] MIPS secondary cache 256kB, 8-way, linesize 32 bytes. [ 0.330000] Synchronize counters for CPU 2: done. [ 0.340000] launch: starting cpu3 [ 0.340000] launch: cpu3 gone! [ 0.340000] CPU3 revision is: 0001992f (MIPS 1004Kc) [ 0.340000] Primary instruction cache 32kB, 4-way, VIPT, linesize 32 bytes. [ 0.340000] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes [ 0.340000] MIPS secondary cache 256kB, 8-way, linesize 32 bytes. [ 0.400000] Synchronize counters for CPU 3: done. [ 0.410000] Brought up 4 CPUs [ 0.410000] devtmpfs: initialized [ 0.410000] NET: Registered protocol family 16 [ 0.700000] release PCIe RST: RALINK_RSTCTRL = 7000000 [ 0.710000] PCIE PHY initialize [ 0.710000] ***** Xtal 40MHz ***** [ 0.710000] start MT7621 PCIe register access [ 1.290000] RALINK_RSTCTRL = 7000000 [ 1.290000] RALINK_CLKCFG1 = 73ffeff8 [ 1.300000] [ 1.300000] *************** MT7621 PCIe RC mode ************* [ 1.780000] pcie_link status = 0x3 [ 1.790000] RALINK_RSTCTRL= 7000000 [ 1.790000] *** Configure Device number setting of Virtual PCI-PCI bridge *** [ 1.800000] RALINK_PCI_PCICFG_ADDR = 21007f2 -> 21007f2 [ 1.800000] PCIE0 enabled [ 1.800000] PCIE1 enabled [ 1.810000] interrupt enable status: 300000 [ 1.810000] Port 1 N_FTS = 1b105000 [ 1.810000] Port 0 N_FTS = 1b105000 [ 1.820000] config reg done [ 1.820000] init_rt2880pci done [ 1.850000] bio: create slab <bio-0> at 0 [ 1.850000] SCSI subsystem initialized [ 1.860000] usbcore: registered new interface driver usbfs [ 1.860000] usbcore: registered new interface driver hub [ 1.870000] usbcore: registered new device driver usb [ 1.870000] PCI host bridge to bus 0000:00 [ 1.880000] pci_bus 0000:00: root bus resource [mem 0x60000000-0x6fffffff] [ 1.880000] pci_bus 0000:00: root bus resource [io 0x1e160000-0x1e16ffff] [ 1.890000] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff] [ 1.890000] pci 0000:00:00.0: bridge configuration invalid ([bus 00-00]), reconfiguring [ 1.900000] pci 0000:00:01.0: bridge configuration invalid ([bus 00-00]), reconfiguring [ 1.900000] pci 0000:00:00.0: BAR 0: can't assign mem (size 0x80000000) [ 1.910000] pci 0000:00:01.0: BAR 0: can't assign mem (size 0x80000000) [ 1.910000] pci 0000:00:00.0: BAR 8: assigned [mem 0x60000000-0x600fffff] [ 1.920000] pci 0000:00:01.0: BAR 8: assigned [mem 0x60100000-0x601fffff] [ 1.920000] pci 0000:00:01.0: BAR 9: assigned [mem 0x60200000-0x602fffff pref] [ 1.930000] pci 0000:00:00.0: BAR 1: assigned [mem 0x60300000-0x6030ffff] [ 1.930000] pci 0000:00:01.0: BAR 1: assigned [mem 0x60310000-0x6031ffff] [ 1.940000] pci 0000:01:00.0: BAR 0: assigned [mem 0x60000000-0x600fffff] [ 1.940000] pci 0000:00:00.0: PCI bridge to [bus 01] [ 1.950000] pci 0000:00:00.0: bridge window [mem 0x60000000-0x600fffff] [ 1.950000] pci 0000:02:00.0: BAR 0: assigned [mem 0x60100000-0x601fffff 64bit] [ 1.960000] pci 0000:02:00.0: BAR 6: assigned [mem 0x60200000-0x6020ffff pref] [ 1.960000] pci 0000:00:01.0: PCI bridge to [bus 02] [ 1.970000] pci 0000:00:01.0: bridge window [mem 0x60100000-0x601fffff] [ 1.970000] pci 0000:00:01.0: bridge window [mem 0x60200000-0x602fffff pref] [ 1.980000] PCI: Enabling device 0000:00:00.0 (0004 -> 0006) [ 1.980000] PCI: Enabling device 0000:00:01.0 (0004 -> 0006) [ 1.990000] BAR0 at slot 0 = 0 [ 1.990000] bus=0x0, slot = 0x0 [ 1.990000] res[0]->start = 0 [ 1.990000] res[0]->end = 0 [ 2.000000] res[1]->start = 60300000 [ 2.000000] res[1]->end = 6030ffff [ 2.000000] res[2]->start = 0 [ 2.000000] res[2]->end = 0 [ 2.010000] res[3]->start = 0 [ 2.010000] res[3]->end = 0 [ 2.010000] res[4]->start = 0 [ 2.010000] res[4]->end = 0 [ 2.020000] res[5]->start = 0 [ 2.020000] res[5]->end = 0 [ 2.020000] BAR0 at slot 1 = 0 [ 2.020000] bus=0x0, slot = 0x1 [ 2.030000] res[0]->start = 0 [ 2.030000] res[0]->end = 0 [ 2.030000] res[1]->start = 60310000 [ 2.030000] res[1]->end = 6031ffff [ 2.040000] res[2]->start = 0 [ 2.040000] res[2]->end = 0 [ 2.040000] res[3]->start = 0 [ 2.040000] res[3]->end = 0 [ 2.050000] res[4]->start = 0 [ 2.050000] res[4]->end = 0 [ 2.050000] res[5]->start = 0 [ 2.050000] res[5]->end = 0 [ 2.060000] bus=0x1, slot = 0x0, irq=0x4 [ 2.060000] res[0]->start = 60000000 [ 2.060000] res[0]->end = 600fffff [ 2.070000] res[1]->start = 0 [ 2.070000] res[1]->end = 0 [ 2.070000] res[2]->start = 0 [ 2.070000] res[2]->end = 0 [ 2.080000] res[3]->start = 0 [ 2.080000] res[3]->end = 0 [ 2.080000] res[4]->start = 0 [ 2.080000] res[4]->end = 0 [ 2.090000] res[5]->start = 0 [ 2.090000] res[5]->end = 0 [ 2.090000] bus=0x2, slot = 0x1, irq=0x18 [ 2.090000] res[0]->start = 60100000 [ 2.100000] res[0]->end = 601fffff [ 2.100000] res[1]->start = 0 [ 2.100000] res[1]->end = 0 [ 2.100000] res[2]->start = 0 [ 2.110000] res[2]->end = 0 [ 2.110000] res[3]->start = 0 [ 2.110000] res[3]->end = 0 [ 2.110000] res[4]->start = 0 [ 2.120000] res[4]->end = 0 [ 2.120000] res[5]->start = 0 [ 2.120000] res[5]->end = 0 [ 2.130000] Switching to clocksource MIPS [ 2.130000] cfg80211: Calling CRDA to update world regulatory domain [ 2.130000] NET: Registered protocol family 2 [ 2.130000] TCP established hash table entries: 2048 (order: 2, 16384 bytes) [ 2.130000] TCP bind hash table entries: 2048 (order: 2, 16384 bytes) [ 2.130000] TCP: Hash tables configured (established 2048 bind 2048) [ 2.130000] TCP: reno registered [ 2.130000] UDP hash table entries: 256 (order: 1, 8192 bytes) [ 2.130000] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes) [ 2.130000] NET: Registered protocol family 1 [ 3.170000] 4 CPUs re-calibrate udelay(lpj = 2924544) [ 3.200000] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 3.200000] msgmni has been set to 491 [ 3.210000] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253) [ 3.210000] io scheduler noop registered (default) [ 3.220000] MIWIFI panic notifier registeredreg_int_mask=0, INT_MASK= 0 [ 3.230000] HSDMA_init [ 3.230000] [ 3.230000] hsdma_phy_tx_ring0 = 0x1bc00000, hsdma_tx_ring0 = 0xbbc00000 [ 3.240000] [ 3.240000] hsdma_phy_rx_ring0 = 0x1bc04000, hsdma_rx_ring0 = 0xbbc04000 [ 3.250000] TX_CTX_IDX0 = 0 [ 3.250000] TX_DTX_IDX0 = 0 [ 3.250000] RX_CRX_IDX0 = 3ff [ 3.250000] RX_DRX_IDX0 = 0 [ 3.260000] set_fe_HSDMA_glo_cfg [ 3.260000] HSDMA_GLO_CFG = 465 [ 3.260000] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled [ 3.270000] serial8250: ttyS0 at MMIO 0x1e000d00 (irq = 27) is a 16550A [ 3.280000] serial8250: ttyS1 at MMIO 0x1e000c00 (irq = 26) is a 16550A [ 3.280000] led=10, on=4000, off=1, blinks,=1, reset=1, time=4000 [ 3.290000] Ralink gpio driver initialized [ 3.300000] brd: module loaded [ 3.300000] MediaTek Nand driver init, version v2.1 Fix AHB virt2phys error [ 3.310000] Allocate 16 byte aligned buffer: 80760360 [ 3.310000] Enable NFI Clock [ 3.320000] # MTK NAND # : Use HW ECC [ 3.320000] NAND ID [C8 D1 80 95 42, 00809542] [ 3.320000] Device found in MTK table, ID: c8d1, EXT_ID: 809542 [ 3.330000] Support this Device in MTK table! c8d1 [ 3.330000] NAND device: Manufacturer ID: 0xc8, Chip ID: 0xd1 (ESMT NAND 128MiB 3,3V 8-bit), 128MiB, page size: 2048, OOB size: 64 [ 3.350000] [NAND]select ecc bit:4, sparesize :64 spare_per_sector=16 [ 3.350000] Scanning device for bad blocks [ 3.500000] Signature matched and data read! [ 3.500000] load_fact_bbt success 1023 [ 3.510000] 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 [ 3.520000] 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 [ 3.530000] 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 [ 3.540000] 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 [ 3.550000] 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 [ 3.560000] 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 [ 3.570000] 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 [ 3.580000] 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 [ 3.590000] Creating 13 MTD partitions on "MT7621-NAND": [ 3.590000] 0x000000000000-0x000007f80000 : "ALL" [ 3.600000] 0x000000000000-0x000000080000 : "Bootloader" [ 3.610000] 0x000000080000-0x0000000c0000 : "Config" [ 3.610000] 0x0000000c0000-0x000000100000 : "Bdata" [ 3.620000] 0x000000100000-0x000000140000 : "Factory" [ 3.620000] 0x000000140000-0x000000180000 : "crash" [ 3.630000] 0x000000180000-0x0000001c0000 : "crash_syslog" [ 3.640000] 0x0000001c0000-0x000000200000 : "reserved0" [ 3.640000] 0x000000200000-0x000000600000 : "kernel0" [ 3.650000] 0x000000600000-0x000000a00000 : "kernel1" [ 3.660000] 0x000000a00000-0x000002a00000 : "rootfs0" [ 3.660000] 0x000002a00000-0x000004a00000 : "rootfs1" [ 3.670000] 0x000004a00000-0x000007f80000 : "overlay" [ 3.680000] [mtk_nand] probe successfully! [ 3.680000] PPP generic driver version 2.4.2 [ 3.690000] PPP BSD Compression module registered [ 3.690000] PPP Deflate Compression module registered [ 3.700000] PPP MPPE Compression module registered [ 3.700000] NET: Registered protocol family 24 [ 3.700000] PPTP driver version 0.8.5 [ 3.710000] ps: can't get major 253 [ 3.710000] GMAC1_MAC_ADRH -- : 0x000034ce [ 3.720000] GMAC1_MAC_ADRL -- : 0x0065bd4f [ 3.720000] Ralink APSoC Ethernet Driver Initilization. v3.1 1024 rx/tx descriptors allocated, mtu = 1500! [ 3.730000] GMAC1_MAC_ADRH -- : 0x000034ce [ 3.730000] GMAC1_MAC_ADRL -- : 0x0065bd4f [ 3.740000] PROC INIT OK! [ 3.740000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 3.750000] ehci-pci: EHCI PCI platform driver [ 3.750000] ehci-platform: EHCI generic platform driver [ 3.760000] *****run project phy. [ 3.780000] FM_OUT value: u4FmOut = 0(0x00000000) [ 3.800000] FM_OUT value: u4FmOut = 0(0x00000000) [ 3.820000] FM_OUT value: u4FmOut = 0(0x00000000) [ 3.840000] FM_OUT value: u4FmOut = 0(0x00000000) [ 3.860000] FM_OUT value: u4FmOut = 0(0x00000000) [ 3.880000] FM_OUT value: u4FmOut = 0(0x00000000) [ 3.900000] FM_OUT value: u4FmOut = 0(0x00000000) [ 3.920000] FM_OUT value: u4FmOut = 0(0x00000000) [ 3.940000] FM_OUT value: u4FmOut = 0(0x00000000) [ 3.960000] FM_OUT value: u4FmOut = 0(0x00000000) [ 4.020000] FM_OUT value: u4FmOut = 0(0x00000000) [ 4.040000] FM_OUT value: u4FmOut = 0(0x00000000) [ 4.060000] FM_OUT value: u4FmOut = 0(0x00000000) [ 4.080000] FM_OUT value: u4FmOut = 0(0x00000000) [ 4.100000] FM_OUT value: u4FmOut = 0(0x00000000) [ 4.120000] FM_OUT value: u4FmOut = 0(0x00000000) [ 4.140000] FM_OUT value: u4FmOut = 0(0x00000000) [ 4.160000] FM_OUT value: u4FmOut = 0(0x00000000) [ 4.180000] FM_OUT value: u4FmOut = 0(0x00000000) [ 4.200000] FM_OUT value: u4FmOut = 0(0x00000000) [ 4.350000] xhci-hcd xhci-hcd: xHCI Host Controller [ 4.350000] xhci-hcd xhci-hcd: new USB bus registered, assigned bus number 1 [ 4.360000] xhci-hcd xhci-hcd: irq 22, io mem 0x1e1c0000 [ 4.370000] hub 1-0:1.0: USB hub found [ 4.370000] hub 1-0:1.0: 2 ports detected [ 4.370000] xhci-hcd xhci-hcd: xHCI Host Controller [ 4.380000] xhci-hcd xhci-hcd: new USB bus registered, assigned bus number 2 [ 4.390000] hub 2-0:1.0: USB hub found [ 4.390000] hub 2-0:1.0: 1 port detected [ 4.390000] usbcore: registered new interface driver usb-storage [ 4.400000] softdog: Software Watchdog Timer: 0.08 initialized. soft_noboot=0 soft_margin=60 sec soft_panic=0 (nowayout=0) [ 4.410000] Netfilter messages via NETLINK v0.30. [ 4.420000] nfnl_acct: registering with nfnetlink. [ 4.420000] nf_conntrack version 0.5.0 (3930 buckets, 15720 max) [ 4.430000] ipip: IPv4 over IPv4 tunneling driver [ 4.430000] gre: GRE over IPv4 demultiplexor driver [ 4.440000] ip_tables: (C) 2000-2006 Netfilter Core Team [ 4.450000] Type=Restricted Cone [ 4.450000] TCP: cubic registered [ 4.450000] NET: Registered protocol family 10 [ 4.460000] NET: Registered protocol family 17 [ 4.460000] l2tp_core: L2TP core driver, V2.0 [ 4.470000] l2tp_ppp: PPPoL2TP kernel driver, V2.0 [ 4.470000] l2tp_netlink: L2TP netlink interface [ 4.480000] 8021q: 802.1Q VLAN Support v1.8 [ 4.480000] MIQEF register done [ 4.490000] Freeing unused kernel memory: 1584K (805a4000 - 80730000) [ 4.500000] csd: CSD deadlock debugging initiated! [ 4.560000] Loading essential drivers... [ 4.570000] Press Ctrl+C to enter RAMFS... [ 4.830000] usb 1-1: new high-speed USB device number 2 using xhci-hcd [ 4.850000] usb 1-1: ep 0x81 - rounding interval to 128 microframes, ep desc says 255 microframes [ 4.860000] add_ep parameters, dev_speed 3, is_in 1, isTT 0, ep_type 2, maxp 512, interval 128, burst 0, mult 0, ep 0x8fe76d80, ep_ctx 0xbbc0d080, sch_ep 0x8f01e680 [ 4.870000] usb 1-1: ep 0x2 - rounding interval to 128 microframes, ep desc says 255 microframes [ 4.880000] add_ep parameters, dev_speed 3, is_in 0, isTT 0, ep_type 2, maxp 512, interval 128, burst 0, mult 0, ep 0x8fe76dac, ep_ctx 0xbbc0d0a0, sch_ep 0x8f01e900 [ 4.900000] usb-storage 1-1:1.0: USB Mass Storage device detected [ 4.900000] scsi0 : usb-storage 1-1:1.0 [ 5.580000] Check for USB recovery... [ 5.590000] Found usb storage, wait for ready [ 6.270000] scsi 0:0:0:0: Direct-Access JetFlash Transcend 4GB 1100 PQ: 0 ANSI: 0 CCS [ 6.280000] sd 0:0:0:0: [sda] 7913472 512-byte logical blocks: (4.05 GB/3.77 GiB) [ 6.290000] sd 0:0:0:0: [sda] Write Protect is off [ 6.300000] sd 0:0:0:0: [sda] No Caching mode page found [ 6.300000] sd 0:0:0:0: [sda] Assuming drive cache: write through [ 6.310000] sd 0:0:0:0: [sda] No Caching mode page found [ 6.320000] sd 0:0:0:0: [sda] Assuming drive cache: write through [ 6.320000] sda: sda1 [ 6.330000] sd 0:0:0:0: [sda] No Caching mode page found [ 6.330000] sd 0:0:0:0: [sda] Assuming drive cache: write through [ 6.340000] sd 0:0:0:0: [sda] Attached SCSI removable disk [ 6.640000] Bringup the system... [ 6.660000] flag_boot_rootfs=0 mounting /dev/mtd10 [ 6.670000] UBI: attaching mtd10 to ubi0 [ 6.970000] UBI: scanning is finished [ 6.990000] UBI: attached mtd10 (name "rootfs0", size 32 MiB) to ubi0 [ 6.990000] UBI: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes [ 7.000000] UBI: min./max. I/O unit sizes: 2048/2048, sub-page size 2048 [ 7.010000] UBI: VID header offset: 2048 (aligned 2048), data offset: 4096 [ 7.010000] UBI: good PEBs: 256, bad PEBs: 0, corrupted PEBs: 0 [ 7.020000] UBI: user volume: 1, internal volumes: 1, max. volumes count: 128 [ 7.030000] UBI: max/mean erase counter: 0/0, WL threshold: 4096, image sequence number: 1090841743 [ 7.030000] UBI: available PEBs: 72, total reserved PEBs: 184, PEBs reserved for bad PEB handling: 20 [ 7.040000] UBI: background thread "ubi_bgt0d" started, PID 437 UBI device number 0, total 256 LEBs (32505856 bytes, 31.0 MiB), available 72 LEBs (9142272 bytes, 8.7 MiB), LEB size 126976 bytes (124.0 KiB) config core 'version' # ROM ver option ROM '2.24.10' # channel option CHANNEL 'release' # hardware platform R1AC or R1N etc. option HARDWARE 'R3G' # CFE ver option UBOOT '1.0.2' # Linux Kernel ver option LINUX '0.0.1' # RAMFS ver option RAMFS '0.0.1' # SQUASHFS ver option SQAFS '0.0.1' # ROOTFS ver option ROOTFS '0.0.1' #build time option BUILDTIME 'Mon, 17 Apr 2017 16:59:11 +0800' #build timestamp option BUILDTS '1492419551' #build git tag option GTAG 'commit 676ed420cef02a2403828351ed482d9ca46e68f9' mount: mounting proc on /proc failed: Device or resource busy mount: mounting sysfs on /sys failed: Device or resource busy [ 8.260000] 34:FFFFFFCE: 0:65:FFFFFFBD:4F [ 8.260000] Raeth v3.1 (Tasklet) [ 8.270000] set CLK_CFG_0 = 0x40a00020!!!!!!!!!!!!!!!!!!1 [ 8.280000] phy_free_head is 0x1bc1c000!!! [ 8.280000] phy_free_tail_phy is 0x1bc1dff0!!! [ 8.290000] txd_pool=bbc20000 phy_txd_pool=1BC20000 [ 8.290000] ei_local->skb_free start address is 0x8feaa6dc. [ 8.300000] free_txd: 1bc20010, ei_local->cpu_ptr: 1BC20000 [ 8.300000] POOL HEAD_PTR | DMA_PTR | CPU_PTR [ 8.310000] ----------------+---------+-------- [ 8.310000] 0xbbc20000 0x1BC20000 0x1BC20000 [ 8.320000] [ 8.320000] phy_qrx_ring = 0x1bc1b000, qrx_ring = 0xbbc1b000 [ 8.330000] [ 8.330000] phy_rx_ring0 = 0x1bc34000, rx_ring0 = 0xbbc34000 [ 8.350000] MT7530 Reset Completed!! [ 8.360000] change HW-TRAP to 0x17c8f [ 8.370000] set LAN/WAN LWLLL [ 8.380000] GMAC1_MAC_ADRH -- : 0x000034ce [ 8.380000] GMAC1_MAC_ADRL -- : 0x0065bd4f [ 8.380000] GDMA2_MAC_ADRH -- : 0x000034ce [ 8.390000] GDMA2_MAC_ADRL -- : 0x0065bd50 [ 8.390000] eth1: ===> VirtualIF_open [ 8.400000] MT7621 GE2 link rate to 1G [ 8.400000] CDMA_CSG_CFG = 81000000 [ 8.400000] GDMA1_FWD_CFG = 20710000 [ 8.400000] GDMA2_FWD_CFG = 20710000 - preinit - Mon Apr 17 17:08:55 UTC 2017 - regular preinit - [ 8.670000] UBI: attaching mtd12 to ubi1 [ 9.170000] UBI: scanning is finished [ 9.190000] UBI: attached mtd12 (name "overlay", size 53 MiB) to ubi1 [ 9.190000] UBI: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes [ 9.200000] UBI: min./max. I/O unit sizes: 2048/2048, sub-page size 2048 [ 9.210000] UBI: VID header offset: 2048 (aligned 2048), data offset: 4096 [ 9.220000] UBI: good PEBs: 428, bad PEBs: 0, corrupted PEBs: 0 [ 9.220000] UBI: user volume: 1, internal volumes: 1, max. volumes count: 128 [ 9.230000] UBI: max/mean erase counter: 1/0, WL threshold: 4096, image sequence number: 1840354541 [ 9.240000] UBI: available PEBs: 0, total reserved PEBs: 428, PEBs reserved for bad PEB handling: 20 [ 9.250000] UBI: background thread "ubi_bgt1d" started, PID 651 UBI device number 1, total 428 LEBs (54345728 bytes, 51.8 MiB), available 0 LEBs (0 bytes), LEB [ 9.260000] UBIFS: background thread "ubifs_bgt1_0" started, PID 655 size 126976 bytes (124.0 KiB) [ 9.330000] UBIFS: recovery needed [ 9.550000] UBIFS: recovery completed [ 9.550000] UBIFS: mounted UBI device 1, volume 0, name "data" [ 9.560000] UBIFS: LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes [ 9.570000] UBIFS: FS size: 50028544 bytes (47 MiB, 394 LEBs), journal size 2539520 bytes (2 MiB, 20 LEBs) [ 9.580000] UBIFS: reserved for root: 2362971 bytes (2307 KiB) [ 9.580000] UBIFS: media format: w4/r0 (latest is w4/r0), UUID 868EE782-07B5-4544-AC5B-78793103AEA2, small LPT model /lib/preinit.sh: line 1: jffs2_not_mounted: not found - init - [ 10.600000] ra2880stop()...Done [ 10.610000] eth1: ===> VirtualIF_close [ 10.610000] Free TX/RX Ring Memory! init started: BusyBox v1.19.4 (2017-04-17 16:55:05 CST) Please press Enter to activate this console. rcS S boot: INFO: rc script run time limit to 65 seconds. [ 10.810000] MIWIFI crash syslog initialized [ 11.850000] NTFS driver 2.1.30 [Flags: R/O MODULE]. [ 12.030000] tntfs: module license 'Commercial. For support email ntfs-support@tuxera.com.' taints kernel. [ 12.040000] Disabling lock debugging due to kernel taint [ 12.060000] Tuxera NTFS driver 3015.1.29 [Flags: R/W MODULE]. [ 12.170000] Tuxera exFAT driver version 3015.8.24 [Flags: R/W MODULE]. [ 12.180000] Built against headers 3.10.14 #1 SMP Mon Jan 9 17:59:15 CST 2017 mips [ 12.190000] Running on kernel 3.10.14 #1 SMP Mon Apr 17 17:08:55 CST 2017 mips [ 12.280000] Tuxera FAT 12/16/32 driver version 3015.1.29 [Flags: R/W MODULE]. [ 12.290000] Built against headers 3.10.14 #1 SMP Mon Jan 9 17:59:15 CST 2017 mips [ 12.300000] Running on kernel 3.10.14 #1 SMP Mon Apr 17 17:08:55 CST 2017 mips [ 12.300000] WARNING: Running kernel does not match configured kernel headers the driver was built with! The driver needs to be rebuilt with the correct kernel headers! [ 12.370000] tun: Universal TUN/TAP device driver, 1.6 [ 12.370000] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com> [ 12.430000] Mirror/redirect action on [ 12.460000] u32 classifier [ 12.460000] input device check on [ 12.470000] Actions configured [ 12.590000] ip_gre: GRE over IPv4 tunneling driver [ 12.630000] xt_time: kernel timezone is +0800 [ 12.720000] ip6_tables: (C) 2000-2006 Netfilter Core Team [ 13.000000] ip_set: protocol 6 [ 13.100000] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 13.150000] sd 0:0:0:0: Attached scsi generic sg0 type 0 [ 13.170000] Traffic lan port is eth0 [ 13.230000] dev_redirect load success. [ 13.760000] <-- RTMPAllocTxRxRingMemory, Status=0, ErrorValue=0x [ 13.760000] <-- RTMPAllocAdapterBlock, Status=0 [ 14.290000] <-- RTMPAllocTxRxRingMemory, Status=0 [ 14.300000] <-- RTMPAllocAdapterBlock, Status=0 [ 14.300000] pAd->CSRBaseAddress =0xc1180000, csr_addr=0xc1180000! [ 14.310000] <dbg> MAC_CSR0=1986146304, RtmpChipOpsHook [ 14.320000] <dbg> dev idx = 1! [ 14.320000] <dbg> get_dev_config_idx pAd->MACVersion = 76623000, pAd->ChipID = 76120044 rcS S calling: /etc/rc.d/S11sysctl boot: logexec: exitcode 1, runt 65 /etc/rc.d/S11sysctl boot Tue Apr 18 01:09:01 CST 2017 netconfig[892]: INFO: loading exist /etc/config/network. Tue Apr 18 01:09:01 CST 2017 netconfig[892]: #### Loopback configuration Tue Apr 18 01:09:01 CST 2017 netconfig[892]: config interface loopback Tue Apr 18 01:09:01 CST 2017 netconfig[892]: option ifname lo Tue Apr 18 01:09:01 CST 2017 netconfig[892]: option proto static Tue Apr 18 01:09:01 CST 2017 netconfig[892]: option ipaddr 127.0.0.1 Tue Apr 18 01:09:01 CST 2017 netconfig[892]: option netmask 255.0.0.0 Tue Apr 18 01:09:01 CST 2017 netconfig[892]: #### LAN configuration Tue Apr 18 01:09:01 CST 2017 netconfig[892]: config interface lan Tue Apr 18 01:09:01 CST 2017 netconfig[892]: option ifname eth0 Tue Apr 18 01:09:01 CST 2017 netconfig[892]: option type bridge Tue Apr 18 01:09:01 CST 2017 netconfig[892]: option proto static Tue Apr 18 01:09:01 CST 2017 netconfig[892]: option ipaddr 192.168.31.1 Tue Apr 18 01:09:01 CST 2017 netconfig[892]: option netmask 255.255.255.0 Tue Apr 18 01:09:01 CST 2017 netconfig[892]: #### WAN configuration Tue Apr 18 01:09:01 CST 2017 netconfig[892]: config interface wan Tue Apr 18 01:09:01 CST 2017 netconfig[892]: option ifname eth1 Tue Apr 18 01:09:01 CST 2017 netconfig[892]: option proto dhcp Tue Apr 18 01:09:01 CST 2017 netconfig[892]: #### IFB interface for MiQoS Tue Apr 18 01:09:01 CST 2017 netconfig[892]: config interface ifb Tue Apr 18 01:09:01 CST 2017 netconfig[892]: option ifname ifb0 Tue Apr 18 01:09:01 CST 2017 netconfig[892]: #### READY configuration Tue Apr 18 01:09:01 CST 2017 netconfig[892]: config interface ready Tue Apr 18 01:09:01 CST 2017 netconfig[892]: option proto static Tue Apr 18 01:09:01 CST 2017 netconfig[892]: option ipaddr 169.254.29.1 Tue Apr 18 01:09:01 CST 2017 netconfig[892]: option netmask 255.255.255.0 [ 16.480000] 34:FFFFFFCE: 0:65:FFFFFFBD:4F [ 16.480000] Raeth v3.1 (Tasklet) [ 16.490000] set CLK_CFG_0 = 0x40a00020!!!!!!!!!!!!!!!!!!1 [ 16.500000] phy_free_head is 0x1bc58000!!! [ 16.500000] phy_free_tail_phy is 0x1bc59ff0!!! [ 16.510000] txd_pool=bbc60000 phy_txd_pool=1BC60000 [ 16.510000] ei_local->skb_free start address is 0x8feaa6dc. [ 16.520000] free_txd: 1bc60010, ei_local->cpu_ptr: 1BC60000 [ 16.520000] POOL HEAD_PTR | DMA_PTR | CPU_PTR [ 16.530000] ----------------+---------+-------- [ 16.530000] 0xbbc60000 0x1BC60000 0x1BC60000 [ 16.540000] [ 16.540000] phy_qrx_ring = 0x1bc1a000, qrx_ring = 0xbbc1a000 [ 16.540000] [ 16.540000] phy_rx_ring0 = 0x1bc5c000, rx_ring0 = 0xbbc5c000 [ 16.580000] MT7530 Reset Completed!! [ 16.590000] change HW-TRAP to 0x17c8f [ 16.590000] set LAN/WAN LWLLL [ 16.600000] GMAC1_MAC_ADRH -- : 0x000034ce [ 16.610000] GMAC1_MAC_ADRL -- : 0x0065bd4f [ 16.610000] eth1: ===> VirtualIF_open [ 16.610000] MT7621 GE2 link rate to 1G [ 16.610000] CDMA_CSG_CFG = 81000000 [ 16.610000] GDMA1_FWD_CFG = 20710000 [ 16.610000] GDMA2_FWD_CFG = 20710000 [ 16.620000] device eth0 entered promiscuous mode [ 16.620000] br-lan: port 1(eth0) entered forwarding state [ 16.620000] br-lan: port 1(eth0) entered forwarding state [ 16.650000] eth1: ===> VirtualIF_open [ 17.150000] efuse_probe: efuse = 10000002 [ 17.330000] tssi_1_target_pwr_g_band = 39 [ 18.620000] br-lan: port 1(eth0) entered forwarding state [ 20.060000] <==== rt28xx_init, Status=0 [ 20.730000] device wl1 entered promiscuous mode [ 20.730000] br-lan: port 2(wl1) entered forwarding state [ 20.740000] br-lan: port 2(wl1) entered forwarding state [ 20.770000] ##### mbss_cr_enable, BssId = 1 [ 21.670000] <dbg> MAC_CSR0=1986146304, rtmp_asic_top_init [ 21.720000] Set defult RDRegion value: CountryCode=CN , RDRegion=0 [ 22.740000] br-lan: port 2(wl1) entered forwarding state [ 24.140000] <==== rt28xx_init, Status=0 [ 24.840000] device wl0 entered promiscuous mode [ 24.840000] br-lan: port 3(wl0) entered forwarding state [ 24.850000] br-lan: port 3(wl0) entered forwarding state [ 26.710000] dev_redirect: add(+) dev redirect mapping: src:eth1->dst:ifb0 [ 26.850000] br-lan: port 3(wl0) entered forwarding state [ 30.030000] dev_redirect: add(+) dev redirect mapping: src:eth1->dst:ifb0 [ 30.160000] Ralink HW NAT Module Enabled [ 30.170000] eth0 ifindex =3 [ 30.180000] eth1 ifindex =5 Tue Apr 18 01:09:17 CST 2017 boot_check[3447]: INFO: Wireless OK [ 32.710000] dev_redirect: add(+) dev redirect mapping: src:eth1->dst:ifb0 [ 41.280000] tcpproxy_init, succeed! [ 42.030000] tfat: fail_safe is enabled [ 42.040000] tfat: cluster_heap_lbo 0x800000 [ 42.040000] tfat: 12 blkbits for normal inodes [ 42.050000] tfat: fat start lbo 0x78000 [ 42.050000] tfat: 12 blkbits for main FAT32 inode [ 42.050000] tfat: cluster size 4096 [ 42.420000] tfat info: FAT32 volume version 0.0. [ 45.610000] Samba Netfilter Hook Enabled [ 54.890000] nf_conntrack: automatic helper assignment is deprecated and it will be removed soon. Use the iptables CT target to attach helpers instead. rcS S boot: INFO: rcS S boot timing 44 seconds. Tue Apr 18 01:09:42 CST 2017 INFO: rcS S boot timing 44 seconds. rcS S boot: system type(R3G/2): SQUASH/3 Tue Apr 18 01:09:42 CST 2017 system type(R3G/2): SQUASH/3 rcS S boot: ROOTFS: /dev/mtdblock13 on / type squashfs (ro,relatime) Tue Apr 18 01:09:42 CST 2017 ROOTFS: /dev/mtdblock13 on / type squashfs (ro,relatime) [ 56.520000] led=6, on=1, off=4000, blinks,=1, reset=1, time=4000 [ 56.530000] led=10, on=1, off=4000, blinks,=1, reset=1, time=4000 [ 56.540000] led=8, on=4000, off=1, blinks,=1, reset=1, time=4000 mknod: /dev/gpio: File exists Tue Apr 18 01:09:43 CST 2017 boot_check[7243]: Booting up finished. [ 58.190000] dev_redirect: add(+) dev redirect mapping: src:eth1->dst:ifb0 BusyBox v1.19.4 (2017-04-17 16:55:05 CST) built-in shell (ash) Enter 'help' for a list of built-in commands. ----------------------------------------------------- Welcome to XiaoQiang! ----------------------------------------------------- $$$$$$\ $$$$$$$\ $$$$$$$$\ $$\ $$\ $$$$$$\ $$\ $$\ $$ __$$\ $$ __$$\ $$ _____| $$ | $$ | $$ __$$\ $$ | $$ | $$ / $$ |$$ | $$ |$$ | $$ | $$ | $$ / $$ |$$ |$$ / $$$$$$$$ |$$$$$$$ |$$$$$\ $$ | $$ | $$ | $$ |$$$$$ / $$ __$$ |$$ __$$< $$ __| $$ | $$ | $$ | $$ |$$ $$< $$ | $$ |$$ | $$ |$$ | $$ | $$ | $$ | $$ |$$ |\$$\ $$ | $$ |$$ | $$ |$$$$$$$$\ $$$$$$$$$ | $$$$$$ |$$ | \$$\ \__| \__|\__| \__|\________| \_________/ \______/ \__| \__|

See also

• List of Xiaomi Devices - Wireless Routers