YunCore AX830
From TechInfoDepot
(Redirected from YunCore AX830-P3)
| abgn+ac+ax (AX3000) | |
|---|---|
| AX3000 Dual-Band WiFi 6 Wireless Ceiling AP | |
|
| |
| Homepage | Product page |
| 3rd Party Firmware | |
| dd-wrt | Status Unknown |
| OpenWrt | Supported |
| Tomato any flavor | Incompatible |
| Gargoyle | Status Unknown |
| Platform | |
| Brand • Model • Rev | YunCore AX830-P3 |
| FCC ID (fcc.io) | none specified |
| FCC ID (fcc.report) | none specified |
| Type | access point |
| CPU1 | Qualcomm IPQ5018 |
| CPU1 Type | ARM Cortex-A53 |
| CPU1 Speed | 1.0 GHz ( 2 cores ) 64-bit |
| Flash1 Chip | Winbond W25N01GWZEIG |
| Flash1 Size | 128 MiB134,217,728 B <br />1,048,576 Kib <br />131,072 KiB <br />1,024 Mib <br />0.125 GiB <br /> (NAND) |
| Flash2 Chip | Winbond W25Q64DW |
| Flash2 Size | 8 MiB8,388,608 B <br />65,536 Kib <br />8,192 KiB <br />64 Mib <br />0.00781 GiB <br /> (SPI NOR) |
| RAM1 Size | 512 MiB536,870,912 B <br />4,194,304 Kib <br />524,288 KiB <br />4,096 Mib <br />0.5 GiB <br /> (DDR3L) |
| RAM1 Chip | Brand? Model? |
| ETH chip1 | Qualcomm IPQ5018 |
| Ethernet Port Count |
1-1GbE-WAN 1-1GbE-LAN |
| Wired Standard | IEEE 802.3i/3u/3ab |
|
802dot11 OUI: none specified | |
| Stock bootloader | U-Boot |
| Expansion IF types | none specified |
| PoE | 802.3at, standard |
| Power | 12 VDC, 1.5 A |
| Connector type | barrel |
| Serial Port (UART) | yes |
|
| |
|
| |
| Other | |
|
| |
| 3rd Party Firmware Support |
OpenWrt • (List | Dev | DLs) |
| Radio 1 | |
| Chip1 | Qualcomm IPQ5018 |
| Wireless interface OUI | none specified |
| Antenna Connector Type | none specified |
| MIMO status | 2x2:2 |
| Wireless Standard | IEEE 802.11b/g/n/ax |
| 802.11ax | up to 574 Mbps |
| 802.11n | up to 300 Mbps |
| 802.11g | up to 54 Mbps |
| 802.11b | up to 11 Mbps |
| WiFi Operating Frequency | 2.4 GHz |
| Radio 2 | |
| Chip1 | Qualcomm QCN6122 |
| Wireless interface OUI | none specified |
| Antenna Connector Type | none specified |
| MIMO status | 2x2:2 |
| Wireless Standard | IEEE 802.11a/n/ac/ax |
| AX-QAM | up to 2402 Mbps |
| 802.11ax | up to 1201 Mbps |
| 802.11ac | up to 867 Mbps |
| 802.11n | up to 300 Mbps |
| 802.11a | up to 54 Mbps |
| WiFi Operating Frequency | 5 GHz |
For a list of all currently documented Qualcomm chipsets with specifications, see Qualcomm.
For a list of all currently documented YunCore devices with specifications, see YunCore.
Flashing
| NOTE: During configuration or flashing a device, the only things that should be hooked to the device is the computer and power. |
Flashing OpenWrt
Target: qualcommax
Subtarget: ipq50xx
Package architecture: aarch64_cortex-a53
Supported Since Commit
Support started version: 25.12.0
Current supported version: 25.12.1
Subtarget: ipq50xx
Package architecture: aarch64_cortex-a53
Supported Since Commit
Support started version: 25.12.0
Current supported version: 25.12.1
WLAN Hardware: Qualcomm IPQ5018 / Qualcomm QCN6122
Installation method(s):
see git-commit
Recovery method(s):
see git-commit
Installation method(s):
see git-commit
Recovery method(s):
see git-commit
| git • >> |
|---|
qualcommax: ipq50xx: Add support for Yuncore AX830
Specifications:
SOC: Qualcomm IPQ5018 (64-bit dual-core ARM Cortex-A53 @ 1.0Ghz)
Memory: 512MB DDR3L
Standard: 802.11ax/ac/b/g/n
Flash: SPI NOR 8MB (Winbond W25Q64DW) + NAND 128MB (Winbond W25N01GWZEIG)
2.4G Frequency: 2.4GHz - 2.484GHz
2.4G Wi-Fi standard: 802.11b/g/n/ax
5.8G Frequency: 4.9~5.9G
5.8G Wi-Fi Standard: 802.11 a/n/ac/ax
Interface:
Optional 1(Without 8081):
1 * 10/100 /1000Mbps RJ45 WAN Port and PoE port;
1* Gigabit Console port;
Optional 2(With 8081):
1 * 10/100/1000/2500Mbps RJ45 WAN port and PoE port,
1*10/100/1000Mbps LAN port
Buttons: 1 * Reset button, press 10 seconds to revert to default setting
Antenna: Build in 4*4dBi dual band MIMO Antenna
Data Rate: 3000Mbps (2.4G 600Mbps, 5.8G 2400Mbps)
End Users: 128+
2.4G RF Power: ≤ 23dBm
5.8G RF Power: ≤ 23dBm
DC: 12V----2A
PoE: 48V (IEEE 802.3at)
LED Light: Sys, WAN, LAN
Power Consumption: ≤ 20W
BACKUP YOUR STOCK FIRMWARE:
- Put openwrt-*-initramfs-uImage.itb to your
TFTP server and rename it to initramfs.bin
- Enable serial console and enter to u-boot cli
and exec these commands:
```
tftpboot <your_tftp_server_ip>:initramfs.bin
bootm
```
- Once boot completed and you get the openwrt shell
execute below commands:
```
device=ax830
mkdir -p /tmp/fw_backup; cd /tmp/fw_backup
rootfs=$(cat /proc/mtd | grep \"rootfs\" | cut -d: -f1)
rootfs_1=$(cat /proc/mtd | grep \"rootfs_1\" | cut -d: -f1)
dd if=/dev/${rootfs} of=rootfs_${rootfs} bs=1M
dd if=/dev/${rootfs_1} of=rootfs_1_${rootfs_1} bs=1M
cp /sys/firmware/fdt fdt.dtb
md5sum * > md5sum
tar -cvzf /tmp/${device}.tar.gz .
sum=$(md5sum /tmp/${device}.tar.gz | cut -d' ' -f1)
mv /tmp/${device}.tar.gz /tmp/${device}_${sum}.tar.gz
echo "stock fw backup saved to: /tmp/${device}_${sum}.tar.gz"
```
- Upload/save your backup to a safe place.
STOCK FIRMWARE RECOVERY:
- Boot initramfs image
- Upload your backed-up stock fw tarball to the device
using scp or download it from the device using wget.
- Enter device ssh cli or tty and exec:
```
cd /tmp && wget <your_web_server_ip>/${stock_fw_backup}.tar.gz`
tar -xpzf ${stock_fw_backup}.tar.gz
rootfs=$(cat /proc/mtd | grep \"rootfs\" | cut -d: -f1)
rootfs_1=$(cat /proc/mtd | grep \"rootfs_1\" | cut -d: -f1)
ubiformat /dev/${rootfs} -y -f /tmp/rootfs_${rootfs}
ubiformat /dev/${rootfs_1} -y -f /tmp/rootfs_1_${rootfs_1}
reboot
```
INSTALLATION:
1. initramfs method
- Put openwrt-*-initramfs-uImage.itb to your
TFTP server and rename it to initramfs.bin
- Enable serial console and enter to u-boot cli
and exec these commands:
```
tftpboot <your_tftp_server_ip>:initramfs.bin
bootm
```
- Once boot completed and you get the openwrt shell
execute below commands:
```
cd /tmp && wget <your_web_server_ip>/factory.ubi`
export rootfs=$(cat /proc/mtd | grep rootfs | cut -d: -f1)
export rootfs_1=$(cat /proc/mtd | grep rootfs_1 | cut -d: -f1)
ubiformat /dev/${rootfs} -y -f factory.ubi
ubiformat /dev/${rootfs_1} -y -f factory.ubi
reboot
```
2. u-boot factory.ubi image method
- Put factory.ubi to your TFTP server and
enter u-boot cli and exec these commands:
```
tftpboot <your_tftp_server_ip>:factory.ubi
#After downloading is finished:
flash rootfs
flash rootfs_1
reset
```
|
Categories:
- YunCore
- Embedded system/access point
- Embedded System Qualcomm
- Embedded System IPQ5018
- Qualcomm
- Embedded System ARM
- Embedded System Cortex-A53
- OpenWrt Supported
- Has Mimo Status
- Embedded System IEEE 802.11b/g/n/ax
- Embedded System QCN6122
- Embedded System IEEE 802.11a/n/ac/ax
- Dual-Radio Wireless Embedded System
- Wireless Embedded System
- Dual-Band
- Embedded System
- English Documentation