YunCore CPE830(D)

multiple revisions of this device, use caution

bgn (N300)
Tanaza Powered Device
Homepage	Product page
3rd Party Firmware
dd-wrt	Status Unknown
OpenWrt	Supported
Tomato any flavor	Incompatible
Gargoyle	Status Unknown
Platform
Brand • Model • Rev	YunCore CPE830(D)
FCC ID	none specified
Type	access point
CPU1 Y	Qualcomm Atheros QCA9533
CPU1 Type	MIPS 24Kc
CPU1 Speed	650 MHz
Flash1 Chip	Brand? Model?
Flash1 Size	16 MiB 16,777,216 B <br />131,072 Kib <br />16,384 KiB <br />128 Mib <br />0.0156 GiB <br />
RAM1 Size	64 MiB 67,108,864 B <br />524,288 Kib <br />65,536 KiB <br />512 Mib <br />0.0625 GiB <br /> (DDR2)
RAM1 Chip	Brand? Model?
ETH chip1	Qualcomm Atheros QCA9533
Switch	Qualcomm Atheros QCA9533
Ethernet Port Count	2-100MbE-LAN
Wired Standard	IEEE 802.3i/3u
802dot11 OUI: none specified
Expansion IF types	none specified
PoE	Passive
Power	? VDC, ? A
Serial Port (UART)	no
Other
3rd Party Firmware Support	OpenWrt • (List | Dev | DLs)
Radio 1
Chip1	Qualcomm Atheros QCA9533
Wireless interface OUI	none specified
Antenna Connector Type	none specified
MIMO status	2x2:2
Wireless Standard	IEEE 802.11b/g/n
802.11n	up to 300 Mbps
802.11g	up to 54 Mbps
802.11b	up to 11 Mbps
WiFi Operating Frequency	2.4 GHz
CPU1 brand Radio1 chip1 brand Radio1 chip2 brand YunCore CPE830 Qualcomm Atheros Qualcomm Atheros YunCore CPE830(D) Qualcomm Atheros Qualcomm Atheros

For a list of all currently documented Qualcomm Atheros (QCA) chipsets with specifications, see Qualcomm Atheros.

For a list of all currently documented YunCore devices with specifications, see YunCore.

• 300 Mbps - 2SS 2.4GHz 802.11n (40MHz chan.) = N300 class

Flashing

Flashing OpenWrt

On the OpenWrt ToH (techdata entry)

Target: ath79
Subtarget: generic
Package architecture: mips_24kc
Supported Since Commit
Support started version: unknown
Current supported version: 25.12.0

WLAN Hardware: Qualcomm Atheros QCA9533
Installation method(s):
see git-commit
Recovery method(s):
see git-commit

git • >>

ath79: add support for KuWfi CPE830(D) / YunCore CPE830(D) Short specification: * 650/600/216 MHz (CPU/DDR/AHB) * 2x 10/100 Mbps Ethernet, passive PoE support * 64 MB of RAM (DDR2) * 16 MB of FLASH * 2T2R 2.4 GHz with external PA, up to 30 dBm (1000mW) * 2x internal 14 dBi antennas * 8x LED, 1x button * No UART on PCB on some versions * Display panel with 2x buttons (F/N) not supported (and not relevant in OpenWrt)- Flash instructions * Connect PC with 192.168.0.141 to WAN port * Install a TFTP server on your PC ('atftp' is doing the job for instance) * Copy your firmware in the TFTP folder as upgrade.bin * Power up device pushing the 'reset' button * The device shall upload upgrade.bin, install it and reboot * Device shall be booting on 192.168.1.1 as default