Database changes have finished applying - please report any issues you're (still) seeing to support@shoutwiki.com.

ZTE MF289F/Serial info

From TechInfoDepot
Jump to navigationJump to search
OEM bootlog • >>
 Captured on TMO_PL_MF289F1V1.0.0B03 firmware:


Format: Log Type - Time(microsec) - Message - Optional Info
Log Type: B - Since Boot(Power On Reset),  D - Delta,  S - Statistic
S - QC_IMAGE_VERSION_STRING=BOOT.BF.3.1.1-00126
S - IMAGE_VARIANT_STRING=DAABANAZA
S - OEM_IMAGE_VERSION_STRING=CRM
S - Boot Config, 0x00000021
S - Reset status Config, 0x00000000
S - Core 0 Frequency, 0 MHz
B -       262 - PBL, Start
B -      1343 - bootable_media_detect_entry, Start
B -      1686 - bootable_media_detect_success, Start
B -      1700 - elf_loader_entry, Start
B -      5135 - auth_hash_seg_entry, Start
B -      7315 - auth_hash_seg_exit, Start
B -    588099 - elf_segs_hash_verify_entry, Start
B -    707680 - PBL, End
B -    707704 - SBL1, Start
B -    798647 - pm_device_init, Start
D -         7 - pm_device_init, Delta
B -    800127 - boot_flash_init, Start
D -     53475 - boot_flash_init, Delta
B -    857757 - boot_config_data_table_init, Start
D -      3871 - boot_config_data_table_init, Delta - (419 Bytes)
B -    864956 - clock_init, Start
D -      7582 - clock_init, Delta
B -    877016 - CDT version:2,Platform ID:8,Major ID:1,Minor ID:0,Subtype:1
B -    880429 - sbl1_ddr_set_params, Start
B -    885526 - cpr_init, Start
D -         2 - cpr_init, Delta
B -    889908 - Pre_DDR_clock_init, Start
D -         4 - Pre_DDR_clock_init, Delta
D -     13175 - sbl1_ddr_set_params, Delta
B -    903221 - pm_driver_init, Start
D -         2 - pm_driver_init, Delta
B -    973721 - sbl1_wait_for_ddr_training, Start
D -        27 - sbl1_wait_for_ddr_training, Delta
B -    989087 - Image Load, Start
D -    152965 - QSEE Image Loaded, Delta - (299560 Bytes)
B -   1142477 - Image Load, Start
D -      1442 - SEC Image Loaded, Delta - (2048 Bytes)
B -   1152762 - Image Load, Start
D -    230987 - APPSBL Image Loaded, Delta - (473243 Bytes)
B -   1384147 - QSEE Execution, Start
D -        60 - QSEE Execution, Delta
B -   1390333 - SBL1, End
D -    684734 - SBL1, Delta
S - Flash Throughput, 2012 KB/s  (775270 Bytes,  385239 us)
S - DDR Frequency, 672 MHz


U-Boot 2012.07 [Chaos Calmer 15.05.1,IPQ4019.ILQ.6.1.0.r2-00006-P-1] (Oct 13 2021 - 14:13:25)

smem ram ptable found: ver: 1 len: 3
DRAM:  256 MiB
machid : 0x8010001
NAND:  spi_nand: spi_nand_flash_probe SF NAND ID ff:ef:aa:21
SF: Detected W25N01GV with page size 2 KiB, total 128 MiB
SF: Detected W25Q16 with page size 4 KiB, total 2 MiB
ipq_spi: page_size: 0x100, sector_size: 0x1000, size: 0x200000
130 MiB
*** Warning - bad CRC, using default environment


Format: Log Type - Time(microsec) - Message - Optional Info
Log Type: B - Since Boot(Power On Reset),  D - Delta,  S - Statistic
S - QC_IMAGE_VERSION_STRING=BOOT.BF.3.1.1-00126
S - IMAGE_VARIANT_STRING=DAABANAZA
S - OEM_IMAGE_VERSION_STRING=CRM
S - Boot Config, 0x00000021
S - Reset status Config, 0x00000000
S - Core 0 Frequency, 0 MHz
B -       262 - PBL, Start
B -      1343 - bootable_media_detect_entry, Start
B -      1686 - bootable_media_detect_success, Start
B -      1700 - elf_loader_entry, Start
B -      5136 - auth_hash_seg_entry, Start
B -      7315 - auth_hash_seg_exit, Start
B -    588238 - elf_segs_hash_verify_entry, Start
B -    707822 - PBL, End
B -    707846 - SBL1, Start
B -    798768 - pm_device_init, Start
D -         7 - pm_device_init, Delta
B -    800248 - boot_flash_init, Start
D -     53495 - boot_flash_init, Delta
B -    857898 - boot_config_data_table_init, Start
D -      3874 - boot_config_data_table_init, Delta - (419 Bytes)
B -    865103 - clock_init, Start
D -      7575 - clock_init, Delta
B -    877158 - CDT version:2,Platform ID:8,Major ID:1,Minor ID:0,Subtype:1
B -    880572 - sbl1_ddr_set_params, Start
B -    885670 - cpr_init, Start
D -         2 - cpr_init, Delta
B -    890053 - Pre_DDR_clock_init, Start
D -         4 - Pre_DDR_clock_init, Delta
D -     13177 - sbl1_ddr_set_params, Delta
B -    903367 - pm_driver_init, Start
D -         2 - pm_driver_init, Delta
B -    973904 - sbl1_wait_for_ddr_training, Start
D -        27 - sbl1_wait_for_ddr_training, Delta
B -    989270 - Image Load, Start
D -    153166 - QSEE Image Loaded, Delta - (299560 Bytes)
B -   1142865 - Image Load, Start
D -      1444 - SEC Image Loaded, Delta - (2048 Bytes)
B -   1153160 - Image Load, Start
D -    231285 - APPSBL Image Loaded, Delta - (473243 Bytes)
B -   1384844 - QSEE Execution, Start
D -        60 - QSEE Execution, Delta
B -   1391030 - SBL1, End
D -    685291 - SBL1, Delta
S - Flash Throughput, 2009 KB/s  (775270 Bytes,  385735 us)
S - DDR Frequency, 672 MHz


U-Boot 2012.07 [Chaos Calmer 15.05.1,IPQ4019.ILQ.6.1.0.r2-00006-P-1] (Oct 13 2021 - 14:13:25)

smem ram ptable found: ver: 1 len: 3
DRAM:  256 MiB
machid : 0x8010001
NAND:  spi_nand: spi_nand_flash_probe SF NAND ID ff:ef:aa:21
SF: Detected W25N01GV with page size 2 KiB, total 128 MiB
SF: Detected W25Q16 with page size 4 KiB, total 2 MiB
ipq_spi: page_size: 0x100, sector_size: 0x1000, size: 0x200000
130 MiB
*** Warning - bad CRC, using default environment

In:    serial
Out:   serial
Err:   serial
machid: 8010001
flash_type: 0
Uaztemain: enter into ! 
ZTE_InitFotaFlashPara: nand_curr_device=1
zte_getHandOffState: read data=0xff from 0x0
Press ESC to abort autoboot in 0 seconds
Creating 1 MTD partitions on "nand1":
0x000001800000-0x000003500000 : "mtd=0"
UBI: attaching mtd2 to ubi0
UBI: physical eraseblock size:   131072 bytes (128 KiB)
UBI: logical eraseblock size:    126976 bytes
UBI: smallest flash I/O unit:    2048
UBI: VID header offset:          2048 (aligned 2048)
UBI: data offset:                4096
UBI: attached mtd2 to ubi0
UBI: MTD device name:            "mtd=0"
UBI: MTD device size:            29 MiB
UBI: number of good PEBs:        232
UBI: number of bad PEBs:         0
UBI: max. allowed volumes:       128
UBI: wear-leveling threshold:    4096
UBI: number of internal volumes: 1
UBI: number of user volumes:     2
UBI: available PEBs:             68
UBI: total number of reserved PEBs: 164
UBI: number of PEBs reserved for bad PEB handling: 2
UBI: max/mean erase counter: 1/0
Read 0 bytes from volume kernel to 84000000
No size specified -> Using max size (4317184)
## Booting kernel from FIT Image at 84000000 ...
   Using 'config@ap.dk04.1-c1' configuration
   Trying 'kernel@1' kernel subimage
     Description:  ARM OpenWrt Linux-3.14.77
     Type:         Kernel Image
     Compression:  gzip compressed
     Data Start:   0x840000e4
     Data Size:    3617305 Bytes = 3.4 MiB
     Architecture: ARM
     OS:           Linux
     Load Address: 0x80208000
     Entry Point:  0x80208000
     Hash algo:    crc32
     Hash value:   de8efe6d
     Hash algo:    sha1
     Hash value:   f13fbe4745e077a32b0f1b0eec269a76f1bc18ab
   Verifying Hash Integrity ... crc32+ sha1+ OK
## Flattened Device Tree from FIT Image at 84000000
   Using 'config@ap.dk04.1-c1' configuration
   Trying 'fdt@ap.dk04.1-c1' FDT blob subimage
     Description:  ARM OpenWrt qcom-ipq40xx-ap.dkxx device tree blob
     Type:         Flat Device Tree
     Compression:  uncompressed
     Data Start:   0x843e9518
     Data Size:    40402 Bytes = 39.5 KiB
     Architecture: ARM
     Hash algo:    crc32
     Hash value:   eeda59d5
     Hash algo:    sha1
     Hash value:   ae0a3c9e5404507aff233137212cc3522ce2b817
   Verifying Hash Integrity ... crc32+ sha1+ OK
   Booting using the fdt blob at 0x843e9518
   Uncompressing Kernel Image ... OK
   Loading Device Tree to 86ff3000, end 86fffdd1 ... OK
Device nand0 not found!
invalid mtd device 'nand1'
eth0 MAC Address from ART is not valid
eth1 MAC Address from ART is not valid
Using machid 0x8010001 from environment

Starting kernel ...

[    0.000000] Booting Linux on physical CPU 0x0
[    0.000000] Initializing cgroup subsys cpuset
[    0.000000] Initializing cgroup subsys cpu
[    0.000000] Initializing cgroup subsys cpuacct
[    0.000000] Linux version 3.14.77 (scl@scl_xa242_062) (gcc version 4.8.3 (OpenWrt/Linaro GCC 4.8-2014.04 IPQ4019.ILQ.6.1.0.r2-00006-P-1) ) #1 SMP PREEMPT Wed Oct 13 14:31:43 CST 2021
[    0.000000] CPU: ARMv7 Processor [410fc075] revision 5 (ARMv7), cr=10c5387d
[    0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[    0.000000] Machine model: Qualcomm Technologies, Inc. IPQ40xx/AP-DK04.1-C1
[    0.000000] Memory policy: Data cache writealloc
[    0.000000] PERCPU: Embedded 7 pages/cpu @cfdc7000 s7744 r8192 d12736 u32768
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 63744
[    0.000000] Kernel command line: ubi.mtd=rootfs root=mtd:ubi_rootfs rootfstype=squashfs rootwait clk_ignore_unused
[    0.000000] PID hash table entries: 1024 (order: 0, 4096 bytes)
[    0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
[    0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
[    0.000000] allocated 524288 bytes of page_cgroup
[    0.000000] please try 'cgroup_disable=memory' option if you don't want memory cgroups
[    0.000000] Memory: 246040K/257024K available (4957K kernel code, 415K rwdata, 1824K rodata, 175K init, 574K bss, 10984K reserved, 0K highmem)
[    0.000000] Virtual kernel memory layout:
[    0.000000]     vector  : 0xffff0000 - 0xffff1000   (   4 kB)
[    0.000000]     fixmap  : 0xfff00000 - 0xfffe0000   ( 896 kB)
[    0.000000]     vmalloc : 0xd0800000 - 0xff000000   ( 744 MB)
[    0.000000]     lowmem  : 0xc0000000 - 0xd0000000   ( 256 MB)
[    0.000000]     pkmap   : 0xbfe00000 - 0xc0000000   (   2 MB)
[    0.000000]     modules : 0xbec00000 - 0xbfe00000   (  18 MB)
[    0.000000]       .text : 0xc0208000 - 0xc08a796c   (6783 kB)
[    0.000000]       .init : 0xc08a8000 - 0xc08d3e40   ( 176 kB)
[    0.000000]       .data : 0xc08d4000 - 0xc093bfc8   ( 416 kB)
[    0.000000]        .bss : 0xc093bfc8 - 0xc09cb854   ( 575 kB)
[    0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
[    0.000000] Preemptible hierarchical RCU implementation.
[    0.000000] NR_IRQS:16 nr_irqs:16 16
[    0.000000] Architected cp15 timer(s) running at 48.00MHz (virt).
[    0.000008] sched_clock: 56 bits at 48MHz, resolution 20ns, wraps every 2863311552512ns
[    0.000017] Switching to timer-based delay loop
[    0.000269] Calibrating delay loop (skipped), value calculated using timer frequency.. 96.00 BogoMIPS (lpj=480000)
[    0.000287] pid_max: default: 32768 minimum: 301
[    0.000547] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.000562] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.012947] Initializing cgroup subsys memory
[    0.012987] Initializing cgroup subsys devices
[    0.013038] CPU: Testing write buffer coherency: ok
[    0.013411] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
[    0.013482] Setting up static identity map for 0x80212808 - 0x80212860
[    0.090672] CPU1: Booted secondary processor
[    0.090716] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001
[    0.110670] CPU2: Booted secondary processor
[    0.110706] CPU2: thread -1, cpu 2, socket 0, mpidr 80000002
[    0.130699] CPU3: Booted secondary processor
[    0.130734] CPU3: thread -1, cpu 3, socket 0, mpidr 80000003
[    0.130884] Brought up 4 CPUs
[    0.130927] SMP: Total of 4 processors activated (384.00 BogoMIPS).
[    0.130936] CPU: All CPU(s) started in SVC mode.
[    0.141785] VFP support v0.3: implementor 41 architecture 2 part 30 variant 7 rev 5
[    0.142282] pinctrl core: initialized pinctrl subsystem
[    0.142707] regulator-dummy: no parameters
[    0.143413] NET: Registered protocol family 16
[    0.144949] DMA: preallocated 2048 KiB pool for atomic coherent allocations
[    0.145579] cpuidle: using governor ladder
[    0.145593] cpuidle: using governor menu
[    0.158707] <CORE> glink_init: unable to create log context
[    0.159194] i2c-msm-v2 78b7000.i2c: probing driver i2c-msm-v2
[    0.159976] sps:sps is ready.
[    0.165541] bio: create slab <bio-0> at 0
[    0.167358] SD0 VccQ: 1800 <--> 3000 mV 
[    0.167998] SCSI subsystem initialized
[    0.168927] msm_bus_fabric_init_driver
[    0.169100] msm_bus_device 580000.ad-hoc-bus: Util-fact is missing, default to 100
[    0.169119] msm_bus_device 580000.ad-hoc-bus: Vrail-comp is missing, default to 100
[    0.169138] msm_bus_device 580000.ad-hoc-bus: Failed to get bus clk for bus4096 ctx1
[    0.169181] msm_bus_device 580000.ad-hoc-bus: Util-fact is missing, default to 100
[    0.169195] msm_bus_device 580000.ad-hoc-bus: Vrail-comp is missing, default to 100
[    0.169212] msm_bus_device 580000.ad-hoc-bus: Failed to get bus clk for bus1024 ctx1
[    0.194793] Advanced Linux Sound Architecture Driver Initialized.
[    0.195696] 80000.qcom,pcie supply vreg-3.3 not found, using dummy regulator
[    0.195785] 80000.qcom,pcie supply vreg-1.8 not found, using dummy regulator
[    0.195841] 80000.qcom,pcie supply vreg-0.9 not found, using dummy regulator
[    0.195894] 80000.qcom,pcie supply gdsc-vdd not found, using dummy regulator
[    0.290488] msm_pcie_enable: msm_pcie_enable: PCIe: trigger the reset of endpoint of RC0.
[    0.300477] msm_pcie_enable: msm_pcie_enable: PCIe RC0 PHY is ready!
[    0.320480] msm_pcie_enable: msm_pcie_enable: PCIe: Release the reset of endpoint of RC0.
[    0.460605] msm_pcie_enable: msm_pcie_enable: RC0:No. 1:LTSSM_STATE:0x0
[    0.500654] msm_pcie_enable: msm_pcie_enable: RC0:No. 2:LTSSM_STATE:0x0
[    0.540703] msm_pcie_enable: msm_pcie_enable: RC0:No. 3:LTSSM_STATE:0x0
[    0.580752] msm_pcie_enable: msm_pcie_enable: RC0:No. 4:LTSSM_STATE:0x0
[    0.620803] msm_pcie_enable: msm_pcie_enable: RC0:No. 5:LTSSM_STATE:0x0
[    0.660852] msm_pcie_enable: msm_pcie_enable: PCIe: trigger the reset of endpoint of RC0.
[    0.660865] msm_pcie_enable: msm_pcie_enable: PCIe RC0 link initialization failed
[    0.660892] msm_pcie_enumerate: msm_pcie_enumerate: PCIe: failed to enable RC0.
[    0.660903] msm_pcie_probe: msm_pcie_probe: PCIe: RC0 is not enabled during bootup; it will be enumerated upon WAKE signal.
[    0.660914] msm_pcie_probe: msm_pcie_probe: PCIe: Driver probe failed for RC0:-1
[    0.661342] msm_pcie: probe of 80000.qcom,pcie failed with error -1
[    0.661591] Switched to clocksource arch_sys_counter
[    0.663367] NET: Registered protocol family 2
[    0.664726] TCP established hash table entries: 2048 (order: 1, 8192 bytes)
[    0.664776] TCP bind hash table entries: 2048 (order: 2, 16384 bytes)
[    0.664827] TCP: Hash tables configured (established 2048 bind 2048)
[    0.664893] TCP: reno registered
[    0.664911] UDP hash table entries: 256 (order: 1, 8192 bytes)
[    0.664942] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
[    0.665302] NET: Registered protocol family 1
[    0.665853] 
[    0.665853] Version Rollback Feature Disabled
[    0.667513] futex hash table entries: 1024 (order: 4, 65536 bytes)
[    0.676731] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    0.677075] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[    0.678058] msgmni has been set to 480
[    0.680093] Key type asymmetric registered
[    0.680110] Asymmetric key parser 'x509' registered
[    0.680151] io scheduler noop registered
[    0.680161] io scheduler deadline registered (default)
[    0.681795] tcsr 194b000.tcsr: setting usb hs phy mode select = e700e7
[    0.681865] tcsr 1953000.ess_tcsr: setting ess interface select = 0
[    0.681941] tcsr 1949000.tcsr: setting wifi_glb_cfg = 41000000
[    0.682000] tcsr 1957000.tcsr: setting wifi_noc_memtype_m0_m2 = 2222222
[    0.683166] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
[    0.684199] msm_serial_hsl_probe: detected port #0 (ttyMSM0)
[    0.684238] msm_serial_hsl_probe: Bus scaling is disabled
[    0.684389] 78af000.serial: ttyMSM0 at MMIO 0x78af000 (irq = 139, base_baud = 115200) is a MSM
[    0.684476] msm_hsl_console_setup: console setup on port #0
[    1.410118] console [ttyMSM0] enabled
[    1.414212] msm_serial_hsl_init: driver initialized
[    1.419049] msm_serial_hs module loaded
[    1.422845] qca_serial_hs module loaded
[    1.428467] sps: BAM device 0x07984000 is not registered yet.
[    1.433242] sps:BAM 0x07984000 is registered.
[    1.437349] msm_nand_bam_init: msm_nand_bam_init: BAM device registered: bam_handle 0xcf0c6e00
[    1.446267] sps:BAM 0x07984000 (va:0xd0b40000) enabled: ver:0x19, number of pipes:7
[    1.453991] msm_nand_version_check: nand_major:1, nand_minor:4, qpic_major:1, qpic_minor:4
[    1.462054] msm_nand_flash_onfi_probe: Found a non ONFI device
[    1.467842] msm_nand_scan: unknown nand flashid=0 manuf=0 devid=0
[    1.473911] msm_nand_probe: No nand device found
[    1.480272] sps: BAM device 0x07884000 is not registered yet.
[    1.485020] sps:BAM 0x07884000 is registered.
[    1.489359] sps:BAM 0x07884000 (va:0xd0b80000) enabled: ver:0x19, number of pipes:12
[    1.497516] m25p80 spi0.0: found s25fl016k, expected n25q128a11
[    1.502993] m25p80 spi0.0: s25fl016k (2048 Kbytes)
[    1.507766] 8 ofpart partitions found on MTD device spi0.0
[    1.513216] Creating 8 MTD partitions on "spi0.0":
[    1.517978] 0x000000000000-0x000000040000 : "0:SBL1"
[    1.524157] 0x000000040000-0x000000060000 : "0:MIBIB"
[    1.529278] 0x000000060000-0x0000000c0000 : "0:QSEE"
[    1.534407] 0x0000000c0000-0x0000000d0000 : "0:CDT"
[    1.539377] 0x0000000d0000-0x0000000e0000 : "0:DDRPARAMS"
[    1.544891] 0x0000000e0000-0x0000000f0000 : "0:APPSBLENV"
[    1.550293] 0x0000000f0000-0x0000001b0000 : "0:APPSBL"
[    1.555367] 0x0000001b0000-0x000000200000 : "0:reserved1"
[    1.572634] libphy: ipq40xx_mdio: probed
[    1.579328] ipq40xx-mdio 90000.mdio: ipq40xx-mdio driver was registered
[    1.585007] i2c /dev entries driver
[    1.590582] sdhci: Secure Digital Host Controller Interface driver
[    1.595760] sdhci: Copyright(c) Pierre Ossman
[    1.600067] sdhci-pltfm: SDHCI platform and OF driver helper
[    1.606339] sdhci_msm 7824900.sdhci: Got SD LDO GPIO #33
[    1.711389] sdhci_msm 7824900.sdhci: Got CD GPIO #22.
[    1.721883] mmc0: no vmmc regulator found
[    1.801636] mmc0: SDHCI controller on 7824900.sdhci [7824900.sdhci] using ADMA
[    1.814773] spinand_probe: enable hw ecc successfully
[    1.820457] nand: zhao.wl g_zte_spi_nand_id =  0xef 
[    1.824413] nand: device found, Manufacturer ID: 0xef, Chip ID: 0xaa
[    1.830721] nand: Winbond W25N01GV 128MiB 3.3V
[    1.835167] nand: 128MiB, SLC, page size: 2048, OOB size: 64
[    1.840795] nand: zhao.wl winbond oob64 
[    1.844721] Scanning device for bad blocks
[    2.127334] random: nonblocking pool is initialized
[    2.819047] 12 ofpart partitions found on MTD device spi0.1
[    2.823610] Creating 12 MTD partitions on "spi0.1":
[    2.828452] 0x000000000000-0x0000000a0000 : "fota-flag"
[    2.834759] 0x0000000a0000-0x000000120000 : "0:ART"
[    2.839587] 0x000000120000-0x0000001a0000 : "mac"
[    2.844350] 0x0000001a0000-0x000000260000 : "reserved2"
[    2.849537] 0x000000260000-0x000000660000 : "cfg-param"
[    2.854807] 0x000000660000-0x000000a60000 : "log"
[    2.859434] 0x000000a60000-0x000000b00000 : "oops"
[    2.864225] 0x000000b00000-0x000001000000 : "reserved3"
[    2.869431] 0x000001000000-0x000001800000 : "web"
[    2.874179] 0x000001800000-0x000003500000 : "rootfs"
[    2.879111] mtd: device 17 (rootfs) set to be root filesystem
[    2.883877] 0x000003500000-0x000004e00000 : "data"
[    2.889676] 0x000004e00000-0x000008000000 : "fota"
[    2.898140] TCP: cubic registered
[    2.901142] NET: Registered protocol family 10
[    2.906050] NET: Registered protocol family 17
[    2.909564] Bridge firewalling registered
[    2.913504] 8021q: 802.1Q VLAN Support v1.8
[    2.917769] Registering SWP/SWPB emulation handler
[    2.923506] regulator-dummy: disabling
[    2.926662] UBI: attaching mtd17 to ubi0
[    3.591146] UBI: scanning is finished
[    3.626980] UBI: attached mtd17 (name "rootfs", size 29 MiB) to ubi0
[    3.632342] UBI: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
[    3.639071] UBI: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
[    3.645776] UBI: VID header offset: 2048 (aligned 2048), data offset: 4096
[    3.652631] UBI: good PEBs: 232, bad PEBs: 0, corrupted PEBs: 0
[    3.658516] UBI: user volume: 2, internal volumes: 1, max. volumes count: 128
[    3.665655] UBI: max/mean erase counter: 1/0, WL threshold: 4096, image sequence number: 135279674
[    3.674593] UBI: available PEBs: 50, total reserved PEBs: 182, PEBs reserved for bad PEB handling: 20
[    3.683833] UBI: background thread "ubi_bgt0d" started, PID 72
[    3.686701] input: gpio_keys.9 as /devices/soc.1/gpio_keys.9/input/input0
[    3.686919] drivers/rtc/hctosys.c: unable to open rtc device (rtc0)
[    3.690322] clk: Not disabling unused clocks
[    3.690327] ALSA device list:
[    3.690330]   No soundcards found.
[    3.724005] VFS: Mounted root (squashfs filesystem) readonly on device 31:21.
[    3.730378] Freeing unused kernel memory: 172K (c08a8000 - c08d3000)
*****************call /etc/preinit_zte*********************
[    4.863984] init: Console is alive
[    4.866549] init: - watchdog -
[    8.489192] usbcore: registered new interface driver usbfs
[    8.493787] usbcore: registered new interface driver hub
[    8.499163] usbcore: registered new device driver usb
[    9.205045] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller
[    9.209531] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 1
[    9.217527] xhci-hcd xhci-hcd.0.auto: irq 164, io mem 0x08a00000
[    9.224198] hub 1-0:1.0: USB hub found
[    9.226966] hub 1-0:1.0: 1 port detected
[    9.231278] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller
[    9.236344] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 2
[    9.244895] hub 2-0:1.0: USB hub found
[    9.247706] hub 2-0:1.0: 1 port detected
[    9.252112] xhci-hcd xhci-hcd.1.auto: xHCI Host Controller
[    9.257057] xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 3
[    9.264976] xhci-hcd xhci-hcd.1.auto: irq 168, io mem 0x06000000
[    9.271571] hub 3-0:1.0: USB hub found
[    9.274478] hub 3-0:1.0: 1 port detected
[    9.278766] xhci-hcd xhci-hcd.1.auto: xHCI Host Controller
[    9.283817] xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 4
[    9.292401] hub 4-0:1.0: USB hub found
[    9.295190] hub 4-0:1.0: config failed, hub doesn't have any ports! (err -19)
[    9.307393] usbcore: registered new interface driver usb-storage
[    9.571957] usb 2-1: new SuperSpeed USB device number 2 using xhci-hcd
[    9.592392] usb 2-1: Parent hub missing LPM exit latency info.  Power management will be impacted.
[    9.870675] init: - preinit -
*****************call /etc/preinit_zte*********************
*****************End of /etc/preinit_zte*********************
[   10.264904] procd: - early -
[   10.266878] procd: - watchdog -
[   11.074788] procd: - ubus -
[   12.084889] procd: - init -
*************ZTE Init Script*************
Please press Enter to activate this console.
[   12.223746] QCE50: __qce_init_clk: Unable to get CE core src clk, set to NULL
[   12.229928] qcrypto 8e20000.qcrypto: Qualcomm Crypto 5.3.1 device found @0x8e20000
[   12.237489] qcrypto 8e20000.qcrypto: CE device = 0x0
[   12.237489] , IO base, CE = 0xd1480000
[   12.237489] , Consumer (IN) PIPE 2,    Producer (OUT) PIPE 3
[   12.237489] IO base BAM = 0x  (null)
[   12.237489] BAM IRQ 239
[   12.237489] Engines Availability = 0x2010453
[   12.262015] sps:BAM 0x08e04000 is registered.
[   12.267072] sps:BAM 0x08e04000 (va:0xd14c0000) enabled: ver:0x27, number of pipes:4
[   12.274925] QCE50: qce_sps_init:  Qualcomm MSM CE-BAM at 0x0000000008e04000 irq 239
[   12.281923] bus_scale_table is NULL
[   12.285269] qcrypto 8e20000.qcrypto: qcrypto-ecb-aes
[   12.290139] qcrypto 8e20000.qcrypto: qcrypto-cbc-aes
[   12.295126] qcrypto 8e20000.qcrypto: qcrypto-ctr-aes
[   12.300031] qcrypto 8e20000.qcrypto: qcrypto-ecb-des
[   12.305002] qcrypto 8e20000.qcrypto: qcrypto-cbc-des
[   12.309924] qcrypto 8e20000.qcrypto: qcrypto-ecb-3des
[   12.314977] qcrypto 8e20000.qcrypto: qcrypto-cbc-3des
[   12.319989] qcrypto 8e20000.qcrypto: qcrypto-xts-aes
[   12.324971] qcrypto 8e20000.qcrypto: qcrypto-sha1
[   12.329633] qcrypto 8e20000.qcrypto: qcrypto-sha256
[   12.334514] qcrypto 8e20000.qcrypto: qcrypto-aead-hmac-sha1-cbc-aes
[   12.340739] qcrypto 8e20000.qcrypto: qcrypto-aead-hmac-sha1-cbc-des
[   12.347014] qcrypto 8e20000.qcrypto: qcrypto-aead-hmac-sha1-cbc-3des
[   12.353357] qcrypto 8e20000.qcrypto: qcrypto-aead-hmac-sha256-cbc-aes
[   12.359750] qcrypto 8e20000.qcrypto: qcrypto-aead-hmac-sha256-cbc-des
[   12.366204] qcrypto 8e20000.qcrypto: qcrypto-aead-hmac-sha256-cbc-3des
[   12.372705] qcrypto 8e20000.qcrypto: qcrypto-hmac-sha1
[   12.377808] qcrypto 8e20000.qcrypto: qcrypto-hmac-sha256
[   12.383125] qcrypto 8e20000.qcrypto: qcrypto-aes-ccm
[   12.388049] qcrypto 8e20000.qcrypto: qcrypto-rfc4309-aes-ccm
[   12.393586] qcrypto: FIPS140-2 Known Answer Tests: Skipped
[   12.409474] nf_conntrack version 0.5.0 (3847 buckets, 15388 max)
[   12.418724] NTFS driver 2.1.30 [Flags: R/O MODULE].
[   12.426015] Initializing XFRM netlink socket
[   12.430578] NET: Registered protocol family 15
[   12.436647] PPP generic driver version 2.4.2
[   13.042993] ssdk_switch_device_num_init[985]:INFO:ess-switch dts node number: 1
[   13.049304] ssdk_dt_get_switch_node[824]:INFO:ess-switch DT exist!
[   13.055438] ssdk_dt_parse_access_mode[725]:INFO:switch_access_mode: local bus
[   13.062566] ssdk_dt_parse_access_mode[738]:INFO:switchreg_base_addr: 0xc000000
[   13.069751] ssdk_dt_parse_access_mode[739]:INFO:switchreg_size: 0x80000
[   13.076351] ssdk_dt_parse_mac_mode[235]:INFO:mac mode = 0x0
[   13.081920] ssdk_dt_parse_mac_mode[241]:INFO:mac mode1 doesn't exit!
[   13.088243] ssdk_dt_parse_mac_mode[250]:INFO:mac mode2 doesn't exit!
[   13.094582] ssdk_dt_parse_phy_info[508]:INFO:qcom,port_phyinfo DT doesn't exist!
[   13.101991] ssdk_dt_parse_mdio[598]:INFO:mdio DT exist!
[   13.107200] ssdk_dt_parse_led[798]:INFO:current dts led_source_num is 5
[   13.113796] ssdk_dt_parse_psgmii[690]:INFO:ess-psgmii DT exist!
[   13.119681] ssdk_plat_init start
[   13.123108] ssdk_plat_init[1231]:ERROR:enable ess clk
[   13.192664] malibu_phy_api_ops_init[2613]:INFO:qca probe malibu phy driver succeeded!
[   13.207477] malibu_phy_hw_init[2484]:INFO:MSF reset phy regiser 0505!
[   13.223439] malibu_phy_hw_init[2484]:INFO:MSF reset phy regiser 0505!
[   13.239304] malibu_phy_hw_init[2484]:INFO:MSF reset phy regiser 0505!
[   13.255159] malibu_phy_hw_init[2484]:INFO:MSF reset phy regiser 0505!
[   13.272443] malibu_phy_hw_init[2484]:INFO:MSF reset phy regiser 0505!
[   13.283074] regi_init[3332]:INFO:Initializing DESS!!
[   15.044465] ssdk_switch_register[1611]:INFO:Chip version 0x1401
[   15.049374] qca_link_polling_select[1273]:INFO:link-polling-required node does not exist
[   15.057424] ssdk_switch_register[1636]:INFO:polling is selected
[   15.063353] regi_init[3341]:INFO:Initializing DESS Done!!
[   15.068792] regi_init[3370]:INFO:qca-ssdk module init succeeded!
[   15.101987] tun: Universal TUN/TAP device driver, 1.6
[   15.106008] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
[   15.118509] **********************************************************
[   15.124062] * Driver    :NSS GMAC Driver - RTL v(3.72a)
[   15.129216] * Version   :1.0
[   15.132100] * Copyright :Copyright (c) 2013-2018 The Linux Foundation. All rights reserved.
[   15.140412] **********************************************************
[   15.163556] l2tp_core: L2TP core driver, V2.0
[   15.168000] l2tp_netlink: L2TP netlink interface
[   15.204906] qca-nss-drv.ko is loaded for symbol link
[   15.211047] sit: IPv6 over IPv4 tunneling driver
[   15.217329] nat46: module (version 8ff2ae59ec9840a7b8b45f976c51cae80abe0226) loaded.
[   15.228461] gre: GRE over IPv4 demultiplexor driver
[   15.233616] ip_gre: GRE over IPv4 tunneling driver
[   15.240725] ip6_gre: GRE over IPv6 tunneling driver
[   15.249029] bonding: Ethernet Channel Bonding Driver: v3.7.1 (April 27, 2011)
[   15.263965] QCA multicast snooping installed successfully
[   15.271731] ip6_tables: (C) 2000-2006 Netfilter Core Team
[   15.281046] ZTE Generic Netlink Module Inserted without Lock
[   15.288002] edma_axi_probe!!!!!!!!!!!!!!!
[   15.292057] zte_nand_local_read():Reading Flash for Calibraton data from 0x0 and partition name is mac
[   15.302174] ***********************************************
[   15.306727] EDMA_LAN using MAC@ - using 10:3c:59:06:f3:89
[   15.312211] EDMA_WAN using MAC@ - using 10:3c:59:05:f3:89
[   15.317487] ***********************************************
[   15.414158] Netfilter messages via NETLINK v0.30.
[   15.420118] ip_set: protocol 6
[   15.454558] QCA Hy-Fi multicast installation successfully
[   15.464431] nss_lag_init[354]:LAG Manager Installed
[   15.471325] NET: Registered protocol family 24
[   15.476713] PPTP driver version 0.8.5
[   15.484148] <NSS-CRYPTO>:module loaded (platform - IPQ806x, build - Build_ID - 10/13/21, 14:14:36)
[   15.492259] <NSS-CRYPTO>:qca-nss-crypto.ko is loaded for symbol link
[   15.499675] crypto bench loaded - Build_ID - 10/13/21, 14:14:39
[   15.504642] nss_crypto_register_user[151]:bf26d21c: Crypto Device is not ready
[   15.514592] nss_macsec init success
[   15.523290] nss_crypto_register_user[151]:bf26d21c: Crypto Device is not ready
[   15.532233] nss is not enabled on this platform
[   15.535747] nss_ipsecmgr_init[1262]:NSS is not enabled in this platform
[   15.547814] nss_crypto_register_user[151]:bf26d21c: Crypto Device is not ready
[   15.555425] nss is not enabled on this platform
[   15.566344] u32 classifier
[   15.568024]     input device check on
[   15.571723]     Actions configured
[   15.577282] Mirror/redirect action on
[   15.606798] fuse init (API version 7.22)
[   15.617176] arp_tables: (C) 2002 David S. Miller
[   15.624976] usbcore: registered new interface driver cdc_wdm
[   15.647177] Ebtables v2.0 registered
[   15.652108] ip_tables: (C) 2000-2006 Netfilter Core Team
[   15.660230] ipt_TRIGGER: module license 'unspecified' taints kernel.
[   15.665630] Disabling lock debugging due to kernel taint
[   15.671894] iptables target:TRIGGER __init
[   15.682546] l2tp_ppp: PPPoL2TP kernel driver, V2.0
[   15.733173] nf_conntrack_rtsp v0.6.21 loading
[   15.815752] nf_nat_rtsp v0.6.21 loading
[   15.832366] PPP MPPE Compression module registered
[   15.861900] usbcore: registered new interface driver usbserial
[   15.866798] usbcore: registered new interface driver usbserial_generic
[   15.873352] usbserial: USB Serial support registered for generic
[   15.921892] xt_time: kernel timezone is -0000
[   15.929069] usbcore: registered new interface driver cdc_ether
[   15.957429] qmi_wwan: probe of 2-1:1.2 failed with error -22
[   15.962236] qmi_wwan 2-1:1.3: bogus CDC Union: master=0, slave=0
[   15.968105] qmi_wwan: probe of 2-1:1.3 failed with error -1
[   15.973762] qmi_wwan 2-1:1.4: bogus CDC Union: master=0, slave=0
[   15.979642] qmi_wwan: probe of 2-1:1.4 failed with error -1
[   15.997205] qmi_wwan 2-1:1.5: cdc-wdm0: USB WDM device
[   16.004416] driver_info->flags 2400 idVendor 19d2 idProduct 1485
[   16.010253] qmi_wwan 2-1:1.5 usb0: register 'qmi_wwan' at usb-xhci-hcd.0.auto-1, Qualcomm WWAN/QMI device, 8e:79:20:ec:68:c6
[   16.020698] [USBNET] MODULE_9x30_QMAP_ENABLE enable & dev->rx_urb_size is 16384 ,dev->rx_qlen is 27,usbnet_memory_mutil is 10
[   16.032161] usbcore: registered new interface driver qmi_wwan
[   16.045448] driver_info->flags 1038 idVendor 19d2 idProduct 1485
[   16.051353] rndis_host 2-1:1.0 rndis0: register 'rndis_host' at usb-xhci-hcd.0.auto-1, RNDIS device, fe:e5:d3:0c:00:ff
[   16.061284] [USBNET] MODULE_9x30_QMAP_ENABLE enable & dev->rx_urb_size is 2048 ,dev->rx_qlen is 222,usbnet_memory_mutil is 10
[   16.072818] usbcore: registered new interface driver rndis_host
[   16.086705] usbcore: registered new interface driver option
[   16.091408] usbserial: USB Serial support registered for GSM modem (1-port)
[   16.098848] option 2-1:1.2: GSM modem (1-port) converter detected
[   16.104339] find modem i:45
[   16.107045] assign port->index 0 
[   16.110550] set urb transfer_flags URB_ZERO_PACKET
[   16.115160] usb_wwan_port_probe add URB_ZERO_PACKET to this urb
[   16.121021] set urb transfer_flags URB_ZERO_PACKET
[   16.125823] usb_wwan_port_probe add URB_ZERO_PACKET to this urb
[   16.131753] set urb transfer_flags URB_ZERO_PACKET
[   16.136476] usb_wwan_port_probe add URB_ZERO_PACKET to this urb
[   16.142435] set urb transfer_flags URB_ZERO_PACKET
[   16.147154] usb_wwan_port_probe add URB_ZERO_PACKET to this urb
[   16.153461] usb 2-1: GSM modem (1-port) converter now attached to ttyUSB0
[   16.160235] option 2-1:1.3: GSM modem (1-port) converter detected
[   16.166004] find modem i:45
[   16.168685] assign port->index 1 
[   16.172293] set urb transfer_flags URB_ZERO_PACKET
[   16.176755] usb_wwan_port_probe add URB_ZERO_PACKET to this urb
[   16.182723] set urb transfer_flags URB_ZERO_PACKET
[   16.187431] usb_wwan_port_probe add URB_ZERO_PACKET to this urb
[   16.193408] set urb transfer_flags URB_ZERO_PACKET
[   16.198110] usb_wwan_port_probe add URB_ZERO_PACKET to this urb
[   16.204085] set urb transfer_flags URB_ZERO_PACKET
[   16.208786] usb_wwan_port_probe add URB_ZERO_PACKET to this urb
[   16.214967] usb 2-1: GSM modem (1-port) converter now attached to ttyUSB1
[   16.221926] option 2-1:1.4: GSM modem (1-port) converter detected
[   16.227593] find modem i:45
[   16.230317] assign port->index 3 
[   16.233918] set urb transfer_flags URB_ZERO_PACKET
[   16.238385] usb_wwan_port_probe add URB_ZERO_PACKET to this urb
[   16.244324] set urb transfer_flags URB_ZERO_PACKET
[   16.249056] usb_wwan_port_probe add URB_ZERO_PACKET to this urb
[   16.254985] set urb transfer_flags URB_ZERO_PACKET
[   16.259733] usb_wwan_port_probe add URB_ZERO_PACKET to this urb
[   16.265691] set urb transfer_flags URB_ZERO_PACKET
[   16.270419] usb_wwan_port_probe add URB_ZERO_PACKET to this urb
[   16.276684] usb 2-1: GSM modem (1-port) converter now attached to ttyUSB2
*************Set Ethernet SMP*************
[   17.004897] yaffs: dev is 32505868 name is "mtdblock12" rw
[   17.009360] yaffs: passed flags ""
[   17.107196] yaffs: dev is 32505869 name is "mtdblock13" rw
[   17.111733] yaffs: passed flags ""
[   17.202572] yaffs: dev is 32505875 name is "mtdblock19" rw
[   17.207027] yaffs: passed flags ""
*************load ECM*************
[   18.009465] ECM init
[   18.010688] ECM database jhash random seed: 0x81eab78d
[   18.017701] ECM init complete

 SSDK Init OK!
operation done.


 SSDK Init OK!
operation done.


 SSDK Init OK!
operation done.


 SSDK Init OK!
operation done.


 SSDK Init OK!
operation done.


 SSDK Init OK!
operation done.


 SSDK Init OK!
operation done.


 SSDK Init OK!
operation done.


 SSDK Init OK!
operation done.


 SSDK Init OK!
operation done.


 SSDK Init OK!
operation done.


 SSDK Init OK!
operation done.


 SSDK Init OK!
operation done.


 SSDK Init OK!
operation done.


 SSDK Init OK!
operation done.


 SSDK Init OK!
operation done.


 SSDK Init OK!
operation done.


 SSDK Init OK!
operation done.


 SSDK Init OK!
operation done.

[   18.355388] Load cfg new driver...
[   18.357770] cfg init, /home/scl/ci/workspace/Soft4_MF289F1_TMOPL_CPE/build_folder/qsdk/build_dir/target-arm_cortex-a7_uClibc-1.0.14_eabi/linux-ipq806x/cfg-1.0/cfg_param.c 583
[   18.449717] 
[   18.450181] CAP_wan_ipaddr=0.0.0
[   18.453393] 4341505f77616e5f6970616464723d302e302e30
[   18.464696] 
[   18.464696]  cfg init end, /home/scl/ci/workspace/Soft4_MF289F1_TMOPL_CPE/build_folder/qsdk/build_dir/target-arm_cortex-a7_uClibc-1.0.14_eabi/linux-ipq806x/cfg-1.0/cfg_param.c 642
[   18.481195] cfg init, /home/scl/ci/workspace/Soft4_MF289F1_TMOPL_CPE/build_folder/qsdk/build_dir/target-arm_cortex-a7_uClibc-1.0.14_eabi/linux-ipq806x/cfg-1.0/cfg_param.c 583
[   18.497164] Not a bridge device, or device not found: br-
[   18.560017] 
[   18.560478] TESTBITSIGNINFO=0000
[   18.563695] 544553544249545349474e494e464f3d30303030
[   18.568707] 
[   18.568707]  cfg init end, /home/scl/ci/workspace/Soft4_MF289F1_TMOPL_CPE/build_folder/qsdk/build_dir/target-arm_cortex-a7_uClibc-1.0.14_eabi/linux-ipq806x/cfg-1.0/cfg_param.c 642
[   18.580852] Not a bridge device, or device not found: br-
[   18.591777] cfg init, /home/scl/ci/workspace/Soft4_MF289F1_TMOPL_CPE/build_folder/qsdk/build_dir/target-arm_cortex-a7_uClibc-1.0.14_eabi/linux-ipq806x/cfg-1.0/cfg_param.c 583
[   18.611439] 
[   18.611934] 
[   18.615110] 0000000000000000000000000000000000000000
[   18.620061] 
[   18.620061]  cfg init end, /home/scl/ci/workspace/Soft4_MF289F1_TMOPL_CPE/build_folder/qsdk/build_dir/target-arm_cortex-a7_uClibc-1.0.14_eabi/linux-ipq806x/cfg-1.0/cfg_param.c 642
[   18.637577] cfg init, /home/scl/ci/workspace/Soft4_MF289F1_TMOPL_CPE/build_folder/qsdk/build_dir/target-arm_cortex-a7_uClibc-1.0.14_eabi/linux-ipq806x/cfg-1.0/cfg_param.c 583
[   18.653265] cfg driver error: /etc_rw/inic/wapi  open failure, file: /home/scl/ci/workspace/Soft4_MF289F1_TMOPL_CPE/build_folder/qsdk/build_dir/target-arm_cortex-a7_uClibc-1.0.14_eabi/linux-ipq806x/cfg-1.0/cfg_param.c, line: 1008!
[   18.673503] 
[   18.681650] 
[   18.683842] 0000000000000000000000000000000000000000
[   18.688795] 
[   18.688795]  cfg init end, /home/scl/ci/workspace/Soft4_MF289F1_TMOPL_CPE/build_folder/qsdk/build_dir/target-arm_cortex-a7_uClibc-1.0.14_eabi/linux-ipq806x/cfg-1.0/cfg_param.c 642
enter is_fota_update_successed.
find a good block.
last find blk_num = 0
****fota_update_flag in /dev/mtd8 is ****
passwd: no record of admin in /etc/shadow, using /etc/passwd
Changing password for admin
New password: 
Bad password: too short
Retype password: 
passwd: password for admin changed by admin
cfg073777
cfg081ec7
cfg091ec7
cfg0af087
cfg0bf087
cfg0cf087
cfg0df087
cfg0ef087
opms_wan_ifname=usb0
LanIfName=br-lan; guest_lan_if=br-Guest 
Thu Jan  1 00:00:22 1970 main.c 365 Successfully initialized wpa_supplicant
killall: syslogd: no process killed
killall: syslogd: no process killed
killall: syslogd: no process killed
[   23.329234] 
/home/scl/ci/workspace/Soft4_MF289F1_TMOPL_CPE/build_folder/qsdk/build_dir/target-arm_cortex-a7_uClibc-1.0.14_eabi/linux-ipq806x/zte_genl_kernel-1.0/zte_genl_kernel_main.c[200]: INFO:Recv from userspace: [Connect request from userspace
]
[   23.350646] 
/home/scl/ci/workspace/Soft4_MF289F1_TMOPL_CPE/build_folder/qsdk/build_dir/target-arm_cortex-a7_uClibc-1.0.14_eabi/linux-ipq806x/zte_genl_kernel-1.0/zte_genl_kernel_main.c[172]: INFO:send msg to user ok, cmd=1, msg=0000  
[   23.371390] 
/home/scl/ci/workspace/Soft4_MF289F1_TMOPL_CPE/build_folder/qsdk/build_dir/target-arm_cortex-a7_uClibc-1.0.14_eabi/linux-ipq806x/zte_genl_kernel-1.0/zte_genl_kernel_main.c[172]: INFO:send msg to user ok, cmd=3, msg=  
zte_wifi_dfs_status_process: dfs=[]
[   24.671111] gpio_keys_gpio_report_event:code=529 state=0
[   24.675537] gpio_keys_gpio_report_event:code=358 state=0
/bin/sh: can't create /sys/class/leds/led:wifi-red/blink: nonexistent directory
/bin/sh: can't create /sys/class/leds/led:wifi-blue/blink: nonexistent directory
/bin/sh: can't create /sys/class/leds/led:wifi-red/brightness: nonexistent directory
/bin/sh: can't create /sys/class/leds/led:wifi-blue/brightness: nonexistent directory
[   24.761720] gpio_keys_gpio_report_event:code=529 state=0
[   24.766032] gpio_keys_gpio_report_event:code=358 state=0
scan the sys dir to find ZTE device & conrresponding driver..........
cat: can't open '/sys/kernel/debug/usb/devices': No such file or directory
crw-r--r--    1 admin    admin     180, 176 Jan  1 00:00 [1;35m/dev/cdc-wdm0[0m
crw-r--r--    1 admin    admin     188,   0 Jan  1 00:00 [1;35m/dev/ttyUSB0[0m
crw-r--r--    1 admin    admin     188,   1 Jan  1 00:00 [1;35m/dev/ttyUSB1[0m
crw-r--r--    1 admin    admin     188,   2 Jan  1 00:00 [1;35m/dev/ttyUSB2[0m
/dev/bus/usb/:
drwxr-xr-x    2 admin    admin           60 Jan  1 00:00 [1;34m001[0m
drwxr-xr-x    2 admin    admin           80 Jan  1 00:00 [1;34m002[0m
drwxr-xr-x    2 admin    admin           60 Jan  1 00:00 [1;34m003[0m
drwxr-xr-x    2 admin    admin           60 Jan  1 00:00 [1;34m004[0m

/dev/bus/usb/001:
crw-r--r--    1 admin    admin     189,   0 Jan  1 00:00 [1;35m001[0m

/dev/bus/usb/002:
crw-r--r--    1 admin    admin     189, 128 Jan  1 00:00 [1;35m001[0m
crw-r--r--    1 admin    admin     189, 129 Jan  1 00:00 [1;35m002[0m

/dev/bus/usb/003:
crw-r--r--    1 admin    admin     189, 256 Jan  1 00:00 [1;35m001[0m

/dev/bus/usb/004:
crw-r--r--    1 admin    admin     189, 384 Jan  1 00:00 [1;35m001[0m
ifconfig: SIOCGIFFLAGS: No such device
opms_wan_ifname=usb0
LanIfName=br-lan; guest_lan_if=br-Guest 
Sorry, rule does not exist.
Sorry, rule does not exist.
Sorry, rule does not exist.
Sorry, rule does not exist.
* daemon not running. starting it now on port 5037 *
enter launch_server server_port is 5037 
launch_server pipe path & pid: /usr/bin/adb, 890 
launch_server pipe path & pid: /usr/bin/adb, 0 
pid=0 and server_port is : 5037
wifi_start_mode=2
launch_server temp value: O,K,

* daemon started successfully *
mac=[10:3C:59:07:F3:89]
mac=[10:3C:59:07:F3:89]
mac=[10:3C:59:07:F3:89]
 @@@@@ wifi_start_mode with CAP or AP @@@@@@ 
killall: zte_daemon: no process killed
killall: dnsmasq: no process killed
killall: zte_router: no process killed
killall: zte_redirect: no process killed
killall: udhcpc: no process killed
killall: udhcpd: no process killed
killall: zte_ipv6_slaac: no process killed
killall: radvd: no process killed
killall: ndppd: no process killed
uci: Entry not found
Error: Failed to connect to ubus
Command failed: Not found
Command failed: Not found
3 KB/s (146 bytes in 0.042s)
[   29.196940] IPv6: ADDRCONF(NETDEV_UP): br-Guest: link is not ready
[   29.217540] device eth1 entered promiscuous mode
[   29.232367] IPv6: ADDRCONF(NETDEV_UP): br-lan: link is not ready
[   29.925762] __mc_netlink_receive: Disable bridge snooping!
[   30.235964] br-lan: port 1(eth1) entered forwarding state
[   30.240446] br-lan: port 1(eth1) entered forwarding state
[   30.246173] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
[   31.388814] __mc_netlink_receive: Disable bridge snooping!
[   32.033210] __mc_netlink_receive: Enable bridge snooping!
[   32.231599] br-lan: port 1(eth1) entered forwarding state
opms_wan_ifname=usb0
LanIfName=br-lan; guest_lan_if=br-Guest 
CURRENT WAN MODE:PPP
internet.sh is called, the argument is []
killall: pppoecd: no process killed
killall: udhcpc: no process killed
killall: zte_trx_router: no process killed
killall: udhcpd: no process killed
killall: dnsmasq: no process killed
killall: miniupnpd: no process killed
Create bridge br-lan..........
device br-lan already exists; can't create bridge with the same name
Create guest bridge br-Guest..........
device br-Guest already exists; can't create bridge with the same name
/sbin/internet.sh: line 99: can't create /proc/sys/net/ipv6/conf/br-Guest/accept_ra#turn: nonexistent directory
Sorry, rule does not exist.
Sorry, rule does not exist.
use usb as wan port !!!!
Sorry, rule does not exist.
Sorry, rule does not exist.
call setPortAsAllLAN............
lan_ip: 192.168.0.1, lan_netmask: 255.255.255.0..........
[   34.728266] device eth1 left promiscuous mode
[   34.731907] br-lan: port 1(eth1) entered disabled state
device eth0 is not a slave of br-lan
[   34.777613] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[   34.786619] device eth1 entered promiscuous mode
[   34.790805] br-lan: port 1(eth1) entered forwarding state
[   34.795681] br-lan: port 1(eth1) entered forwarding state
[   34.805807] device eth0 entered promiscuous mode
opms_wan_ifname=usb0
[   34.891629] br-lan: port 1(eth1) entered forwarding state
opms_wan_ifname=usb0
LanIfName=br-lan; guest_lan_if=br-Guest 
killall: udhcpd: no process killed
killall: dnsmasq: no process killed
begin
middle
else section
mang_num: -1
list_first_item: 
one_num: -1
###the format of mac_ip_list is valid###
3 KB/s (150 bytes in 0.040s)
3 KB/s (150 bytes in 0.039s)
3 KB/s (150 bytes in 0.040s)
begin
middle
else section
mang_num: -1
list_first_item: 
one_num: -1
###the format of mac_ip_list is valid###
opms_wan_ifname=usb0
LanIfName=br-lan; guest_lan_if=br-Guest 
#######start the mtu_set.sh##########
192.168.0.1255.255.255.0init_dns_ip:tmp_byte_netmask is 0
init_dns_ip:tmp_byte_netmask is 255
init_dns_ip:tmp_byte_netmask is 255
init_dns_ip:tmp_byte_netmask is 255
#######end the mtu_set.sh##########
iptables: No chain/target/match by that name.
iptables: No chain/target/match by that name.
 dual_core_board_if= rndis0....
iptables: No chain/target/match by that name.
killall: zte_router: no process killed
killall: zte_ipv6_slaac: no process killed
iptables: No chain/target/match by that name.
iptables v1.4.21: Couldn't load target `redirect_rules':No such file or directory

Try `iptables -h' or 'iptables --help' for more information.
iptables v1.4.21: Couldn't load target `redirect_rules':No such file or directory

Try `iptables -h' or 'iptables --help' for more information.
iptables v1.4.21: Couldn't load target `redirect_rules':No such file or directory

Try `iptables -h' or 'iptables --help' for more information.
opms_wan_ifname=usb0
LanIfName=br-lan; guest_lan_if=br-Guest 
iptables v1.4.21: Couldn't load target `remote_mark':No such file or directory

Try `iptables -h' or 'iptables --help' for more information.
module is not loaded
iptables: No chain/target/match by that name.
iptables: No chain/target/match by that name.
module is not loaded
iptables v1.4.21: Couldn't load target `vpn_client_output':No such file or directory

Try `iptables -h' or 'iptables --help' for more information.
module is not loaded
iptables: No chain/target/match by that name.
iptables: No chain/target/match by that name.
[   37.424763] +++++++http_redirect load, g_web_redirect_gateway=[192.168.0.1], g_odu_lan_ipaddr=[0.0.0.0] ...
[   37.433792] +++++++http_redirect load, g_web_redirect_mode=[http]...
iptables v1.4.21: Couldn't load target `vpn_client_prerouting[   37.444156] 
/home/scl/ci/workspace/Soft4_MF289F1_TMOPL_CPE/build_folder/qsdk/build_dir/target-arm_cortex-a7_uClibc-1.0.14_eabi/linux-ipq806x/zte_genl_kernel-1.0/zte_genl_kernel_main.c[200]: INFO:':No such file or directory

Try `iptables -h' or 'iptables --Recv from userspace: [5]
help' for more information.
iptables: No chain/target/match by that name.
iptables: No chain/target/match by that name.
iptables: No chain/target/match by that name.
iptables: No chain/target/match by that name.
iptables: No chain/target/match by that name.
iptables: No chain/target/match by that name.
iptables: No chain/target/match by that name.
iptables: No chain/target/match by that name.
iptables: No chain/target/match by that name.
ip6tables: No chain/target/match by that name.
ip6tables: No chain/target/match by that name.
ip6tables: No chain/target/match by that name.
ip6tables: No chain/target/match by that name.
ip6tables: No chain/target/match by that name.
/bin/sh: zte_user_connect: not found

iptables: No chain/target/match by that name.
iptables: No chain/target/match by that name.
/bin/sh: zte_topsw_send_msg_to_sleep_for_cpe: not found

iptables: No chain/target/match by that name.
iptables: No chain/target/match by that name.
iptables: No chain/target/match by that name.
iptables: No chain/target/match by that name.
iptables: No chain/target/match by that name.
iptables: No chain/target/match by that name.
iptables: No chain/target/match by that name.
iptables: No chain/target/match by that name.
iptables: No chain/target/match by that name.
iptables: No chain/target/match by that name.
iptables: No chain/target/match by that name.
ath0      no private ioctls.

ath0      no private ioctls.

ath1      no private ioctls.

ath1      no private ioctls.

ath0      no private ioctls.

ath0      no private ioctls.

ath1      no private ioctls.

ath1      no private ioctls.

ath0      No such device

ath0      no private ioctls.

ath0      no private ioctls.

ath0      no private ioctls.

ath0      no private ioctls.

ath0      no private ioctls.

ath0      no private ioctls.

ath1      No such device

ath1      no private ioctls.

ath1      no private ioctls.

iptables: No chain/target/match by that name.
ath1      no private ioctls.

iptables: No chain/target/match by that name.
ath1      no private ioctls.

ath1      no private ioctls.

iptables: Chain already exists.
ath1      no private ioctls.

tcp_detect_port_list: 53,123,1900,139,445,4719,80,443,7547
wifi1     no private ioctls.

opms_wan_ifname=usb0
wifi0     no private ioctls.

LanIfName=br-lan; guest_lan_if=br-Guest 
killall: miniupnpd: no process killed
opms_wan_ifname=usb0
LanIfName=br-lan; guest_lan_if=br-Guest 
iptables: No chain/target/match by that name.
iptables v1.4.21: Couldn't load target `MINIUPNPD':No such file or directory

Try `iptables -h' or 'iptables --help' for more information.
iptables: No chain/target/match by that name.
iptables: No chain/target/match by that name.
iptables v1.4.21: Couldn't load target `MINIUPNPD':No such file or directory

Try `iptables -h' or 'iptables --help' for more information.
iptables: No chain/target/match by that name.
iptables: No chain/target/match by that name.
iptables v1.4.21: Couldn't load target `MINIUPNPD-POSTROUTING':No such file or directory

Try `iptables -h' or 'iptables --help' for more information.
iptables: No chain/target/match by that name.
killall: miniupnpd: no process killed
path: etc_rw...
path: etc_rw...
enter the wifi_create_3 function
enter the wifi_create_2 function
path: etc_rw...
path: etc_rw...
enter the wifi_create_0 function
enter the wifi_create_1 function
opms_wan_ifname=usb0
LanIfName=br-lan; guest_lan_if=br-Guest 
iptables: No chain/target/match by that name.
iptables v1.4.21: Couldn't load target `MINIUPNPD':No such file or directory

Try `iptables -h' or 'iptables --help' for more information.
iptables: No chain/target/match by that name.
iptables: No chain/target/match by that name.
iptables v1.4.21: Couldn't load target `MINIUPNPD':No such file or directory

Try `iptables -h' or 'iptables --help' for more information.
iptables: No chain/target/match by that name.
iptables: No chain/target/match by that name.
iptables v1.4.21: Couldn't load target `MINIUPNPD-POSTROUTING':No such file or directory

Try `iptables -h' or 'iptables --help' for more information.
iptables: No chain/target/match by that name.
************start dos_attack_defender.sh*****************
iptables: No chain/target/match by that name.

 SSDK Init OK!
operation done.

************end dos_attack_defender.sh*****************
qrcode_text = WIFI:T:WPA;S:ZTE_07F389_guest;P:KN7H3238Q3;
qrcode_text = WIFI:T:WPA;S:ZTE_07F389_guest;P:KN7H3238Q3;
qrcode_text = WIFI:T:WPA;S:ZTE_07F389;P:EBJT52JXB4;
qrcode_text = WIFI:T:WPA;S:ZTE_07F389;P:EBJT52JXB4;
opms_wan_ifname=usb0
LanIfName=br-lan; guest_lan_if=br-Guest 
#######start the mtu_set.sh##########
[   39.695506] 
/home/scl/ci/workspace/Soft4_MF289F1_TMOPL_CPE/build_folder/qsdk/build_dir/target-arm_cortex-a7_uClibc-1.0.14_eabi/linux-ipq806x/zte_genl_kernel-1.0/zte_genl_kernel_main.c[200]: INFO:Recv from userspace: [5]
iptables: No chain/target/match by that name.
iptables: No chain/target/match by that name.

Reading chip1_ssid1_qr 
Reading chip2_ssid2_qr .
Reading chip1_ssid1_qr .
Reading chip2_ssid2_qr o
Read OK chip1_ssid1_qr o
Read OK chip2_ssid2_qr 
Reading chip1_ssid2_qr .
Reading chip1_ssid2_qr o
Read OK chip1_ssid2_qr 
Reading chip2_ssid1_qr .
Reading chip2_ssid1_qr o
Read OK chip2_ssid1_qr 
Writing chip1_ssid1_qr 
OK      chip1_ssid1_qr 

Writing chip2_ssid2_qr 
OK      chip2_ssid2_qr 
iptables: Chain already exists.

Writing chip1_ssid2_qr 
OK      chip1_ssid2_qr 

Writing chip2_ssid1_qr 
OK      chip2_ssid1_qr 
#######end the mtu_set.sh##########
ussd is disabled
/etc/init.d/zte_init.sh: line 197: telnetd: not found
recv msg from server is :HELLO
[   40.229625] yaffs: dev is 32505867 name is "mtdblock11" rw
[   40.235474] yaffs: passed flags ""
mount: mounting /dev/mtdblock11 on /etc_rw/fota failed: Invalid argument
Sat Jan  1 00:00:00 UTC 2000
Sat Jan  1 00:00:00 UTC 2000

CST-1CDT, M3.5.0/02:00:00, M10.5.0/03:00:00
CST-1CDT, M3.5.0/02:00:00, M10.5.0/03:00:00
module is already loaded - nf_conntrack_sip
module is already loaded - nf_nat_sip
module is already loaded - nf_conntrack_pptp
goahead initWebs info: webdir is /etc_ro/web/web!
webs: Listening for HTTP requests at address 192.168.0.1
module is already loaded - nf_nat_pptp
module is already loaded - nf_conntrack_ftp
module is already loaded - nf_nat_ftp
module is already loaded - nf_conntrack_h323
module is already loaded - nf_nat_h323
module is already loaded - nf_conntrack_rtsp
module is already loaded - nf_nat_rtsp
module is already loaded - nf_conntrack_tftp
module is already loaded - nf_nat_tftp
opms_wan_ifname=usb0
LanIfName=br-lan; guest_lan_if=br-Guest 
webs: Listening for HTTPS requests at port 443
iptables: No chain/target/match by that name.
iptables: Chain already exists.
ip6tables: Chain already exists.
iptables: No chain/target/match by that name.
tcp_detect_port_list: 53,123,1900,139,445,4719,80,443,7547
opms_wan_ifname=usb0
LanIfName=br-lan; guest_lan_if=br-Guest 
killall: miniupnpd: no process killed
opms_wan_ifname=usb0
LanIfName=br-lan; guest_lan_if=br-Guest 
iptables: No chain/target/match by that name.
iptables v1.4.21: Couldn't load target `MINIUPNPD':No such file or directory

Try `iptables -h' or 'iptables --help' for more information.
iptables: No chain/target/match by that name.
iptables: No chain/target/match by that name.
iptables v1.4.21: Couldn't load target `MINIUPNPD':No such file or directory

Try `iptables -h' or 'iptables --help' for more information.
iptables: No chain/target/match by that name.
iptables: No chain/target/match by that name.
iptables v1.4.21: Couldn't load target `MINIUPNPD-POSTROUTING':No such file or directory

Try `iptables -h' or 'iptables --help' for more information.
iptables: No chain/target/match by that name.
killall: miniupnpd: no process killed
opms_wan_ifname=usb0
LanIfName=br-lan; guest_lan_if=br-Guest 
iptables: No chain/target/match by that name.
iptables v1.4.21: Couldn't load target `MINIUPNPD':No such file or directory

Try `iptables -h' or 'iptables --help' for more information.
iptables: No chain/target/match by that name.
iptables: No chain/target/match by that name.
iptables v1.4.21: Couldn't load target `MINIUPNPD':No such file or directory

Try `iptables -h' or 'iptables --help' for more information.
iptables: No chain/target/match by that name.
iptables: No chain/target/match by that name.
iptables v1.4.21: Couldn't load target `MINIUPNPD-POSTROUTING':No such file or directory

Try `iptables -h' or 'iptables --help' for more information.
iptables: No chain/target/match by that name.
************start dos_attack_defender.sh*****************
iptables: No chain/target/match by that name.

 SSDK Init OK!
operation done.

************end dos_attack_defender.sh*****************
opms_wan_ifname=usb0
LanIfName=br-lan; guest_lan_if=br-Guest 
#######start the mtu_set.sh##########
#######end the mtu_set.sh##########
opms_wan_ifname=usb0
LanIfName=br-lan; guest_lan_if=br-Guest 
iptables: Bad rule (does a matching rule exist in that chain?).
iptables: Bad rule (does a matching rule exist in that chain?).
remotemg_white_list=[]
add remote manager done.
enter add_telnet()
disable telnetd on lan side
firewall_sys_fw done
tr069 func is not support, return!
iptables: No chain/target/match by that name.
/bin/sh: parental_control.sh: not found
iptables: No chain/target/match by that name.
iptables v1.4.21: Couldn't load target `time_limit_filter':No such file or directory

Try `iptables -h' or 'iptables --help' for more information.
iptables: No chain/target/match by that name.
ip6tables: No chain/target/match by that name.
ip6tables v1.4.21: Couldn't load target `time_limit_filter':No such file or directory

Try `ip6tables -h' or 'ip6tables --help' for more information.
ip6tables: No chain/target/match by that name.
mkdir: can't create directory '/var/log': File exists
speed limit is disabled, so we need to clear iptable and tc rules
userflowEnable=0,so we need to enable SFE
module is already loaded - ecm
iptables: No chain/target/match by that name.
iptables: No chain/target/match by that name.
00:00:04 UP>>[update_control.c:2878]########---Update_Control Start---########
RTNETLINK answers: Invalid argument
Cannot find device "br1"
00:00:05 UP>>[update_control.c:2883]modem is QC_MODEM
RTNETLINK answers: Invalid argument
mkdir: can't create directory '/var/log': File exists
iptables v1.4.21: Couldn't load target `wifi_multissid_isolate':No such file or directory

Try `iptables -h' or 'iptables --help' for more information.
iptables: No chain/target/match by that name.
iptables: No chain/target/match by that name.
iptables v1.4.21: Couldn't load target `second_ssid_access_control':No such file or directory

Try `iptables -h' or 'iptables --help' for more information.
iptables: No chain/target/match by that name.
iptables: No chain/target/match by that name.
iptables v1.4.21: Couldn't load target `wifi_main_guest_ssid_isolate':No such file or directory

Try `iptables -h' or 'iptables --help' for more information.
iptables: No chain/target/match by that name.
iptables: No chain/target/match by that name.
************Set WiFi SMP Affinity********************
cat: can't open '/sys/class/net/wifi0/hwcaps': No such file or directory
cat: can't open '/sys/class/net/wifi1/hwcaps': No such file or directory
zte_port_status_monitor_create_msg_queue(): msgid = [524304]
normal mode!
zte_ripc
zte_ripc start without parameter 
wifi_start_mode is 2.
zte_ripc server
iMsgHandle is 557073
zte_ripc begin to rcv msg from queue 557073. 
00:00:20 UP>>[update_control.c:2684]modem_detect_Func_attest enter
unzip: can't open /etc_rw/fota/image.zip[.zip]
unzip: can't open /cache/image.zip[.zip]

00:00:20 UP>>[update_control.c:2941]start zte_dm
00:00:20 UP>>[update_control.c:2196]fsm turn from 0 to 0.
DM_RemoveFile name /etc_rw/config/dm/tree_zdm.xml
06:50:40 UP>>[libdua.c:142]dm_update_control_result=0
15:38:20 UP>>[libdua.c:158]fota_upgrade_result=
DM_RemoveFile name /etc_rw/fota/image.zip
DM_RemoveFile name /etc_rw/config/dm/FUMO_SESSION_KEY_dlResumeData.txt.0
426 KB/s (20480 bytes in 0.046s)


OpenWrt 24.10.2 bootlog • >>
 Captured on stock 24.10.2: 




Format: Log Type - Time(microsec) - Message - Optional Info
Log Type: B - Since Boot(Power On Reset),  D - Delta,  S - Statistic
S - QC_IMAGE_VERSION_STRING=BOOT.BF.3.1.1-00126
S - IMAGE_VARIANT_STRING=DAABANAZA
S - OEM_IMAGE_VERSION_STRING=CRM
S - Boot Config, 0x00000021
S - Reset status Config, 0x00000000
S - Core 0 Frequency, 0 MHz
B -       262 - PBL, Start
B -      1343 - bootable_media_detect_entry, Start
B -      1686 - bootable_media_detect_success, Start
B -      1700 - elf_loader_entry, Start
B -      5130 - auth_hash_seg_entry, Start
B -      7307 - auth_hash_seg_exit, Start
B -    587120 - elf_segs_hash_verify_entry, Start
B -    706576 - PBL, End
B -    706600 - SBL1, Start
B -    797619 - pm_device_init, Start
D -         7 - pm_device_init, Delta
B -    799097 - boot_flash_init, Start
D -     53415 - boot_flash_init, Delta
B -    856667 - boot_config_data_table_init, Start
D -      3874 - boot_config_data_table_init, Delta - (419 Bytes)
B -    863872 - clock_init, Start
D -      7583 - clock_init, Delta
B -    875936 - CDT version:2,Platform ID:8,Major ID:1,Minor ID:0,Subtype:1
B -    879349 - sbl1_ddr_set_params, Start
B -    884446 - cpr_init, Start
D -         2 - cpr_init, Delta
B -    888828 - Pre_DDR_clock_init, Start
D -         4 - Pre_DDR_clock_init, Delta
D -     13175 - sbl1_ddr_set_params, Delta
B -    902141 - pm_driver_init, Start
D -         2 - pm_driver_init, Delta
B -    972580 - sbl1_wait_for_ddr_training, Start
D -        27 - sbl1_wait_for_ddr_training, Delta
B -    988168 - Image Load, Start
D -    153047 - QSEE Image Loaded, Delta - (299560 Bytes)
B -   1141642 - Image Load, Start
D -      1444 - SEC Image Loaded, Delta - (2048 Bytes)
B -   1151934 - Image Load, Start
D -    231081 - APPSBL Image Loaded, Delta - (473243 Bytes)
B -   1383412 - QSEE Execution, Start
D -        60 - QSEE Execution, Delta
B -   1389597 - SBL1, End
D -    685104 - SBL1, Delta
S - Flash Throughput, 2011 KB/s  (775270 Bytes,  385411 us)
S - DDR Frequency, 672 MHz


U-Boot 2012.07 [Chaos Calmer 15.05.1,IPQ4019.ILQ.6.1.0.r2-00006-P-1] (Oct 13 2021 - 14:13:25)

smem ram ptable found: ver: 1 len: 3
DRAM:  256 MiB
machid : 0x8010001
NAND:  spi_nand: spi_nand_flash_probe SF NAND ID ff:ef:aa:21
SF: Detected W25N01GV with page size 2 KiB, total 128 MiB
SF: Detected W25Q16 with page size 4 KiB, total 2 MiB
ipq_spi: page_size: 0x100, sector_size: 0x1000, size: 0x200000
130 MiB
*** Warning - bad CRC, using default environment


Format: Log Type - Time(microsec) - Message - Optional Info
Log Type: B - Since Boot(Power On Reset),  D - Delta,  S - Statistic
S - QC_IMAGE_VERSION_STRING=BOOT.BF.3.1.1-00126
S - IMAGE_VARIANT_STRING=DAABANAZA
S - OEM_IMAGE_VERSION_STRING=CRM
S - Boot Config, 0x00000021
S - Reset status Config, 0x00000000
S - Core 0 Frequency, 0 MHz
B -       262 - PBL, Start
B -      1343 - bootable_media_detect_entry, Start
B -      1686 - bootable_media_detect_success, Start
B -      1700 - elf_loader_entry, Start
B -      5131 - auth_hash_seg_entry, Start
B -      7308 - auth_hash_seg_exit, Start
B -    587210 - elf_segs_hash_verify_entry, Start
B -    706674 - PBL, End
B -    706698 - SBL1, Start
B -    797690 - pm_device_init, Start
D -         7 - pm_device_init, Delta
B -    799169 - boot_flash_init, Start
D -     53384 - boot_flash_init, Delta
B -    856707 - boot_config_data_table_init, Start
D -      3871 - boot_config_data_table_init, Delta - (419 Bytes)
B -    863905 - clock_init, Start
D -      7565 - clock_init, Delta
B -    875951 - CDT version:2,Platform ID:8,Major ID:1,Minor ID:0,Subtype:1
B -    879365 - sbl1_ddr_set_params, Start
B -    884463 - cpr_init, Start
D -         2 - cpr_init, Delta
B -    888846 - Pre_DDR_clock_init, Start
D -         4 - Pre_DDR_clock_init, Delta
D -     13178 - sbl1_ddr_set_params, Delta
B -    902160 - pm_driver_init, Start
D -         2 - pm_driver_init, Delta
B -    972631 - sbl1_wait_for_ddr_training, Start
D -        27 - sbl1_wait_for_ddr_training, Delta
B -    988218 - Image Load, Start
D -    153145 - QSEE Image Loaded, Delta - (299560 Bytes)
B -   1141792 - Image Load, Start
D -      1445 - SEC Image Loaded, Delta - (2048 Bytes)
B -   1152084 - Image Load, Start
D -    231248 - APPSBL Image Loaded, Delta - (473243 Bytes)
B -   1383731 - QSEE Execution, Start
D -        60 - QSEE Execution, Delta
B -   1389968 - SBL1, End
D -    685270 - SBL1, Delta
S - Flash Throughput, 2010 KB/s  (775270 Bytes,  385677 us)
S - DDR Frequency, 672 MHz


U-Boot 2012.07 [Chaos Calmer 15.05.1,IPQ4019.ILQ.6.1.0.r2-00006-P-1] (Oct 13 2021 - 14:13:25)

smem ram ptable found: ver: 1 len: 3
DRAM:  256 MiB
machid : 0x8010001
NAND:  spi_nand: spi_nand_flash_probe SF NAND ID ff:ef:aa:21
SF: Detected W25N01GV with page size 2 KiB, total 128 MiB
SF: Detected W25Q16 with page size 4 KiB, total 2 MiB
ipq_spi: page_size: 0x100, sector_size: 0x1000, size: 0x200000
130 MiB
*** Warning - bad CRC, using default environment

In:    serial
Out:   serial
Err:   serial
machid: 8010001
flash_type: 0
Uaztemain: enter into ! 
ZTE_InitFotaFlashPara: nand_curr_device=1
zte_getHandOffState: read data=0xff from 0x0
Press ESC to abort autoboot in 0 seconds
Creating 1 MTD partitions on "nand1":
0x000001800000-0x000003500000 : "mtd=0"
UBI: attaching mtd2 to ubi0
UBI: physical eraseblock size:   131072 bytes (128 KiB)
UBI: logical eraseblock size:    126976 bytes
UBI: smallest flash I/O unit:    2048
UBI: VID header offset:          2048 (aligned 2048)
UBI: data offset:                4096
UBI: attached mtd2 to ubi0
UBI: MTD device name:            "mtd=0"
UBI: MTD device size:            29 MiB
UBI: number of good PEBs:        232
UBI: number of bad PEBs:         0
UBI: max. allowed volumes:       128
UBI: wear-leveling threshold:    4096
UBI: number of internal volumes: 1
UBI: number of user volumes:     3
UBI: available PEBs:             18
UBI: total number of reserved PEBs: 214
UBI: number of PEBs reserved for bad PEB handling: 2
UBI: max/mean erase counter: 2/1
Read 0 bytes from volume kernel to 84000000
No size specified -> Using max size (3428352)
## Booting kernel from FIT Image at 84000000 ...
   Using 'config@ap.dk04.1-c1' configuration
   Trying 'kernel-1' kernel subimage
     Description:  ARM OpenWrt Linux-6.6.93
     Type:         Kernel Image
     Compression:  uncompressed
     Data Start:   0x840000e4
     Data Size:    3311840 Bytes = 3.2 MiB
     Architecture: ARM
     OS:           Linux
     Load Address: 0x80208000
     Entry Point:  0x80208000
     Hash algo:    crc32
     Hash value:   8843df84
     Hash algo:    sha1
     Hash value:   b746c5c384f1f374944ddc8f6df227674f40dbfb
   Verifying Hash Integrity ... crc32+ sha1+ OK
## Flattened Device Tree from FIT Image at 84000000
   Using 'config@ap.dk04.1-c1' configuration
   Trying 'fdt-1' FDT blob subimage
     Description:  ARM OpenWrt zte_mf289f device tree blob
     Type:         Flat Device Tree
     Compression:  uncompressed
     Data Start:   0x84328af8
     Data Size:    19284 Bytes = 18.8 KiB
     Architecture: ARM
     Hash algo:    crc32
     Hash value:   5e7d0a5c
     Hash algo:    sha1
     Hash value:   02e49c078a101d13cb27758db05c5bcb085a54f4
   Verifying Hash Integrity ... crc32+ sha1+ OK
   Booting using the fdt blob at 0x84328af8
   Loading Kernel Image ... OK
OK
   Loading Device Tree to 86ff8000, end 86fffb53 ... OK
ipq: fdt fixup unable to find compatible node
Device nand0 not found!
invalid mtd device 'nand1'
eth0 MAC Address from ART is not valid
eth1 MAC Address from ART is not valid
Using machid 0x8010001 from environment

Starting kernel ...

[    0.000000] Booting Linux on physical CPU 0x0
[    0.000000] Linux version 6.6.93 (builder@buildhost) (arm-openwrt-linux-muslgnueabi-gcc (OpenWrt GCC 13.3.0 r28739-d9340319c6) 13.3.0, GNU ld (GNU Binutils) 2.42) #0 SMP Mon Jun 23 20:40:36 2025
[    0.000000] CPU: ARMv7 Processor [410fc075] revision 5 (ARMv7), cr=10c5387d
[    0.000000] CPU: div instructions available: patching division code
[    0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[    0.000000] OF: fdt: Machine model: ZTE MF289F
[    0.000000] Memory policy: Data cache writealloc
[    0.000000] OF: reserved mem: 0x87e00000..0x87e7ffff (512 KiB) nomap non-reusable smem@87e00000
[    0.000000] OF: reserved mem: 0x87e80000..0x87ffffff (1536 KiB) nomap non-reusable tz@87e80000
[    0.000000] Zone ranges:
[    0.000000]   Normal   [mem 0x0000000080000000-0x000000008fffffff]
[    0.000000]   HighMem  empty
[    0.000000] Movable zone start for each node
[    0.000000] Early memory node ranges
[    0.000000]   node   0: [mem 0x0000000080000000-0x0000000087dfffff]
[    0.000000]   node   0: [mem 0x0000000087e00000-0x0000000087ffffff]
[    0.000000]   node   0: [mem 0x0000000088000000-0x000000008fffffff]
[    0.000000] Initmem setup node 0 [mem 0x0000000080000000-0x000000008fffffff]
[    0.000000] percpu: Embedded 13 pages/cpu s21588 r8192 d23468 u53248
[    0.000000] Kernel command line: ubi.mtd=rootfs root=mtd:ubi_rootfs rootfstype=squashfs rootwait root=/dev/ubiblock0_1
[    0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes, linear)
[    0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes, linear)
[    0.000000] Built 1 zonelists, mobility grouping on.  Total pages: 64960
[    0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off
[    0.000000] Memory: 246128K/262144K available (7669K kernel code, 643K rwdata, 1136K rodata, 1024K init, 247K bss, 16016K reserved, 0K cma-reserved, 0K highmem)
[    0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
[    0.000000] rcu: Hierarchical RCU implementation.
[    0.000000] 	Tracing variant of Tasks RCU enabled.
[    0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies.
[    0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16
[    0.000000] rcu: srcu_init: Setting srcu_struct sizes based on contention.
[    0.000000] arch_timer: cp15 timer(s) running at 48.00MHz (virt).
[    0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0xb11fd3bfb, max_idle_ns: 440795203732 ns
[    0.000001] sched_clock: 56 bits at 48MHz, resolution 20ns, wraps every 4398046511096ns
[    0.000018] Switching to timer-based delay loop, resolution 20ns
[    0.000338] Calibrating delay loop (skipped), value calculated using timer frequency.. 96.00 BogoMIPS (lpj=480000)
[    0.000361] CPU: Testing write buffer coherency: ok
[    0.000409] pid_max: default: 32768 minimum: 301
[    0.010186] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
[    0.010211] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
[    0.018701] qcom_scm: convention: smc legacy
[    0.020159] RCU Tasks Trace: Setting shift to 2 and lim to 1 rcu_task_cb_adjust=1 rcu_task_cpu_ids=4.
[    0.020334] Setting up static identity map for 0x80300000 - 0x8030003c
[    0.020519] rcu: Hierarchical SRCU implementation.
[    0.020527] rcu: 	Max phase no-delay instances is 1000.
[    0.021211] smp: Bringing up secondary CPUs ...
[    0.024861] smp: Brought up 1 node, 4 CPUs
[    0.024886] SMP: Total of 4 processors activated (384.00 BogoMIPS).
[    0.024896] CPU: All CPU(s) started in SVC mode.
[    0.033442] VFP support v0.3: implementor 41 architecture 2 part 30 variant 7 rev 5
[    0.033620] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[    0.033651] futex hash table entries: 1024 (order: 4, 65536 bytes, linear)
[    0.038741] pinctrl core: initialized pinctrl subsystem
[    0.042156] NET: Registered PF_NETLINK/PF_ROUTE protocol family
[    0.042554] DMA: preallocated 256 KiB pool for atomic coherent allocations
[    0.043920] thermal_sys: Registered thermal governor 'step_wise'
[    0.044038] cpuidle: using governor ladder
[    0.044081] cpuidle: using governor menu
[    0.062323] cryptd: max_cpu_qlen set to 1000
[    0.067036] usbcore: registered new interface driver usbfs
[    0.067158] usbcore: registered new interface driver hub
[    0.067240] usbcore: registered new device driver usb
[    0.067296] pps_core: LinuxPPS API ver. 1 registered
[    0.067303] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[    0.067329] PTP clock support registered
[    0.070046] clocksource: Switched to clocksource arch_sys_counter
[    0.080585] NET: Registered PF_INET protocol family
[    0.080814] IP idents hash table entries: 4096 (order: 3, 32768 bytes, linear)
[    0.082544] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 4096 bytes, linear)
[    0.082584] Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear)
[    0.082606] TCP established hash table entries: 2048 (order: 1, 8192 bytes, linear)
[    0.082645] TCP bind hash table entries: 2048 (order: 3, 32768 bytes, linear)
[    0.082727] TCP: Hash tables configured (established 2048 bind 2048)
[    0.083755] MPTCP token hash table entries: 256 (order: 0, 4096 bytes, linear)
[    0.084139] UDP hash table entries: 256 (order: 1, 8192 bytes, linear)
[    0.084183] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes, linear)
[    0.084896] NET: Registered PF_UNIX/PF_LOCAL protocol family
[    0.084950] PCI: CLS 0 bytes, default 64
[    0.086682] workingset: timestamp_bits=14 max_order=16 bucket_order=2
[    0.087704] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    0.087719] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[    0.422437] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 248)
[    0.428268] tcsr 1949000.tcsr: setting wifi_glb_cfg = 41000000
[    0.428382] tcsr 194b000.tcsr: setting usb hs phy mode select = e700e7
[    0.428477] tcsr 1953000.ess_tcsr: setting ess interface select = 0
[    0.428568] tcsr 1957000.tcsr: setting wifi_noc_memtype_m0_m2 = 2222222
[    0.428974] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled
[    0.430918] qcom-pcie 40000000.pci: host bridge /soc/pci@40000000 ranges:
[    0.430989] qcom-pcie 40000000.pci:       IO 0x0040200000..0x00402fffff -> 0x0000000000
[    0.431024] qcom-pcie 40000000.pci:      MEM 0x0040300000..0x0040ffffff -> 0x0040300000
[    0.433059] msm_serial 78af000.serial: msm_serial: detected port #0
[    0.433108] msm_serial 78af000.serial: uartclk = 1843200
[    0.433496] 78af000.serial: ttyMSM0 at MMIO 0x78af000 (irq = 31, base_baud = 115200) is a MSM
[    0.433534] msm_serial: console setup on port #0
[    0.433585] printk: console [ttyMSM0] enabled
[    0.571907] qcom-pcie 40000000.pci: iATU: unroll F, 32 ob, 8 ib, align 4K, limit 4G
[    0.579137] msm_serial: driver initialized
[    0.585501] qcom-pcie 40000000.pci: Invalid eDMA IRQs found
[    0.598774] loop: module loaded
[    1.067880] spi_qup 78b5000.spi: IN:block:16, fifo:64, OUT:block:16, fifo:64
[    1.069593] flash@0 enforce active low on GPIO handle
[    1.076864] spi-nand@1 enforce active low on GPIO handle
[    1.083246] spi-nor spi0.0: s25fl016k (2048 Kbytes)
[    1.087213] 8 fixed-partitions partitions found on MTD device spi0.0
[    1.091750] Creating 8 MTD partitions on "spi0.0":
[    1.098305] 0x000000000000-0x000000040000 : "0:SBL1"
[    1.103745] 0x000000040000-0x000000060000 : "0:MIBIB"
[    1.108593] 0x000000060000-0x0000000c0000 : "0:QSEE"
[    1.113616] 0x0000000c0000-0x0000000d0000 : "0:CDT"
[    1.118653] 0x0000000d0000-0x0000000e0000 : "0:DDRPARAMS"
[    1.123257] 0x0000000e0000-0x0000000f0000 : "0:APPSBLENV"
[    1.128804] 0x0000000f0000-0x0000001b0000 : "0:APPSBL"
[    1.134239] 0x0000001b0000-0x000000200000 : "0:reserved1"
[    1.143810] spi-nand spi0.1: Winbond SPI NAND was found.
[    1.144053] spi-nand spi0.1: 128 MiB, block size: 128 KiB, page size: 2048, OOB size: 64
[    1.149729] 12 fixed-partitions partitions found on MTD device spi0.1
[    1.157570] Creating 12 MTD partitions on "spi0.1":
[    1.163872] 0x000000000000-0x0000000a0000 : "fota-flag"
[    1.170750] 0x0000000a0000-0x000000120000 : "ART"
[    1.175658] OF: Bad cell count for /soc/spi@78b5000/spi-nand@1/partitions
[    1.178843] 0x000000120000-0x0000001a0000 : "mac"
[    1.187391] OF: Bad cell count for /soc/spi@78b5000/spi-nand@1/partitions
[    1.190351] 0x0000001a0000-0x000000260000 : "reserved2"
[    1.199234] 0x000000260000-0x000000660000 : "cfg-param"
[    1.211116] 0x000000660000-0x000000a60000 : "log"
[    1.220461] 0x000000a60000-0x000000b00000 : "oops"
[    1.222577] 0x000000b00000-0x000001000000 : "reserved3"
[    1.235508] 0x000001000000-0x000001800000 : "web"
[    1.253329] 0x000001800000-0x000003500000 : "rootfs"
[    1.314988] mtd: setting mtd17 (rootfs) as root device
[    1.316346] mtdsplit: no squashfs found in "rootfs"
[    1.319053] 0x000003500000-0x000004e00000 : "data"
[    1.377424] 0x000004e00000-0x000008000000 : "fota"
[    1.541618] i2c_dev: i2c /dev entries driver
[    1.543893] sdhci: Secure Digital Host Controller Interface driver
[    1.544973] sdhci: Copyright(c) Pierre Ossman
[    1.551029] sdhci-pltfm: SDHCI platform and OF driver helper
[    1.557849] NET: Registered PF_INET6 protocol family
[    1.562842] Segment Routing with IPv6
[    1.566106] In-situ OAM (IOAM) with IPv6
[    1.569731] NET: Registered PF_PACKET protocol family
[    1.573700] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this.
[    1.578974] 8021q: 802.1Q VLAN Support v1.8
[    1.591961] Registering SWP/SWPB emulation handler
[    1.600216] qcom-pcie 40000000.pci: Phy link never came up
[    1.600600] qcom-pcie 40000000.pci: PCI host bridge to bus 0000:00
[    1.605832] pci_bus 0000:00: root bus resource [bus 00-ff]
[    1.612079] pci_bus 0000:00: root bus resource [io  0x0000-0xfffff]
[    1.617461] pci_bus 0000:00: root bus resource [mem 0x40300000-0x40ffffff]
[    1.619006] qca8k-ipq4019 c000000.switch: configuring for fixed/internal link mode
[    1.623685] pci 0000:00:00.0: [17cb:1001] type 01 class 0x060400
[    1.630917] qca8k-ipq4019 c000000.switch: Link is Up - 1Gbps/Full - flow control rx/tx
[    1.638128] pci 0000:00:00.0: reg 0x10: [mem 0x00000000-0x00000fff]
[    1.652081] pci 0000:00:00.0: PME# supported from D0 D3hot
[    1.659979] PCI: bus0: Fast back to back transfers disabled
[    1.663939] PCI: bus1: Fast back to back transfers enabled
[    1.669221] pci 0000:00:00.0: BAR 0: assigned [mem 0x40300000-0x40300fff]
[    1.674774] pci 0000:00:00.0: PCI bridge to [bus 01-ff]
[    1.685564] pcieport 0000:00:00.0: AER: enabled with IRQ 59
[    1.841927] qca8k-ipq4019 c000000.switch wan (uninitialized): PHY [90000.mdio-1:01] driver [Qualcomm QCA8075] (irq=POLL)
[    1.920871] qca8k-ipq4019 c000000.switch lan (uninitialized): PHY [90000.mdio-1:04] driver [Qualcomm QCA8075] (irq=POLL)
[    1.921952] ipqess-edma c080000.ethernet eth0: entered promiscuous mode
[    1.930979] DSA: tree 0 setup
[    1.937459] ubi0: attaching mtd17
[    2.489705] ubi0: scanning is finished
[    2.517540] ubi0: attached mtd17 (name "rootfs", size 29 MiB)
[    2.517595] ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
[    2.522352] ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
[    2.529060] ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096
[    2.535952] ubi0: good PEBs: 232, bad PEBs: 0, corrupted PEBs: 0
[    2.542702] ubi0: user volume: 3, internal volumes: 1, max. volumes count: 128
[    2.548940] ubi0: max/mean erase counter: 2/1, WL threshold: 4096, image sequence number: 135279674
[    2.555991] ubi0: available PEBs: 0, total reserved PEBs: 232, PEBs reserved for bad PEB handling: 20
[    2.564947] ubi0: background thread "ubi_bgt0d" started, PID 89
[    2.567051] block ubiblock0_1: created from ubi0:1(rootfs[    2.603631] VFS: Mounted root (squashfs filesystem) readonly on device 254:0.
[    2.605674] Freeing unused kernel image (initmem) memory: 1024K
[    2.610010] Run /sbin/init as init process
[    2.960094] random: crng init done
[    3.414571] init: Console is alive
[    3.414910] init: - watchdog -
[    4.633951] kmodloader: loading kernel modules from /etc/modules-boot.d/*
[    4.663600] gpio_button_hotplug: loading out-of-tree module taints kernel.
[    4.890233] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller
[    4.890322] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 1
[    4.894881] xhci-hcd xhci-hcd.0.auto: hcc params 0x0228f665 hci version 0x100 quirks 0x0000008002000010
[    4.902297] xhci-hcd xhci-hcd.0.auto: irq 61, io mem 0x08a00000
[    4.911798] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller
[    4.917482] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 2
[    4.923057] xhci-hcd xhci-hcd.0.auto: Host supports USB 3.0 SuperSpeed
[    4.931479] hub 1-0:1.0: USB hub found
[    4.937224] hub 1-0:1.0: 1 port detected
[    4.941462] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM.
[    4.945604] hub 2-0:1.0: USB hub found
[    4.953182] hub 2-0:1.0: 1 port detected
[    4.957180] xhci-hcd xhci-hcd.1.auto: xHCI Host Controller
[    4.960753] xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 3
[    4.966213] xhci-hcd xhci-hcd.1.auto: USB3 root hub has no ports
[    4.973590] xhci-hcd xhci-hcd.1.auto: hcc params 0x0220f665 hci version 0x100 quirks 0x0000008002000010
[    4.979855] xhci-hcd xhci-hcd.1.auto: irq 62, io mem 0x06000000
[    4.991659] hub 3-0:1.0: USB hub found
[    4.994907] hub 3-0:1.0: 1 port detected
[    5.002394] kmodloader: done loading kernel modules from /etc/modules-boot.d/*
[    5.012305] init: - preinit -
Cannot parse config file '/etc/fw_env.config': No such file or directory
Failed to find NVMEM device
[    7.047750] ipqess-edma c080000.ethernet eth0: configuring for fixed/internal link mode
[    7.048509] qca8k-ipq4019 c000000.switch lan: configuring for phy/psgmii link mode
[    7.054641] qca8k-ipq4019 c000000.switch: PSGMII calibration!
[    7.062307] ipqess-edma c080000.ethernet eth0: Link is Up - 1Gbps/Full - flow control rx/tx
Press the [f] key and hit [enter] to enter failsafe mode
Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level
[    8.120251] usb 2-1: new SuperSpeed USB device number 2 using xhci-hcd
[   12.333259] UBIFS (ubi0:2): Mounting in unauthenticated mode
[   12.333528] UBIFS (ubi0:2): background thread "ubifs_bgt0_2" started, PID 230
[   12.483149] UBIFS (ubi0:2): recovery needed
[   12.865400] UBIFS (ubi0:2): recovery completed
[   12.865575] UBIFS (ubi0:2): UBIFS: mounted UBI device 0, volume 2, name "rootfs_data"
[   12.868765] UBIFS (ubi0:2): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
[   12.876707] UBIFS (ubi0:2): FS size: 16887808 bytes (16 MiB, 133 LEBs), max 143 LEBs, journal size 1015809 bytes (0 MiB, 7 LEBs)
[   12.886585] UBIFS (ubi0:2): reserved for root: 797652 bytes (778 KiB)
[   12.898204] UBIFS (ubi0:2): media format: w5/r0 (latest is w5/r0), UUID A5BD64BA-4F23-452C-9B02-868FDFD842BB, small LPT model
[   12.918995] mount_root: switching to ubifs overlay
[   12.958370] urandom-seed: Seeding with /etc/urandom.seed
[   13.197623] procd: - early -
[   13.197851] procd: - watchdog -
[   13.873233] procd: - watchdog -
[   13.896249] procd: - ubus -
[   14.115655] procd: - init -
Please press Enter to activate this console.
[   14.967009] kmodloader: loading kernel modules from /etc/modules.d/*
[   15.018649] usbcore: registered new interface driver cdc_wdm
[   15.019480] Loading modules backported from Linux version v6.12.6-0-ge9d65b48ce1a
[   15.023445] Backport generated by backports.git v6.1.110-1-35-g410656ef04d2
[   15.045151] usbcore: registered new interface driver usbserial_generic
[   15.045279] usbserial: USB Serial support registered for generic
[   15.277147] PPP generic driver version 2.4.2
[   15.278440] NET: Registered PF_PPPOX protocol family
[   15.299235] qmi_wwan 2-1:1.5: cdc-wdm0: USB WDM device
[   15.300544] qmi_wwan 2-1:1.5 wwan0: register 'qmi_wwan' at usb-xhci-hcd.0.auto-1, WWAN/QMI device, ca:c4:68:ad:45:6f
[   15.303710] usbcore: registered new interface driver qmi_wwan
[   15.867874] urngd: v1.0.2 started.
[   16.898200] ath10k_ahb a000000.wifi: qca4019 hw1.0 target 0x01000000 chip_id 0x003b00ff sub 0000:0000
[   16.898273] ath10k_ahb a000000.wifi: kconfig debug 0 debugfs 1 tracing 0 dfs 1 testmode 0
[   16.910192] ath10k_ahb a000000.wifi: firmware ver 10.4b-ct-4019-fW-13-5ae337bb1 api 5 features mfp,peer-flow-ctrl,txstatus-noack,wmi-10.x-CT,ratemask-CT,regdump-CT,txrate-CT,flush-all-CT,pingpong-CT,ch-regs-CT,nop-CT,set-special-CT,tx-rc-CT,cust-stats-CT,txrate2-CT,beacon-cb-CT,wmi-block-ack-CT,wmi-bcn-rc-CT crc32 6b2b5c5b
[   17.081293] ath10k_ahb a000000.wifi: board_file api 2 bmi_id 0:20 crc32 2d972a4b
[   18.378799] ath10k_ahb a000000.wifi: 10.4 wmi init: vdevs: 16  peers: 48  tid: 96
[   18.378867] ath10k_ahb a000000.wifi: msdu-desc: 2500  skid: 32
[   18.428140] ath10k_ahb a000000.wifi: wmi print 'P 48/48 V 16 K 144 PH 176 T 186  msdu-desc: 2500  sw-crypt: 0 ct-sta: 0'
[   18.429091] ath10k_ahb a000000.wifi: wmi print 'free: 53252 iram: 13432 sram: 35752'
[   18.572954] ath10k_ahb a000000.wifi: htt-ver 2.2 wmi-op 6 htt-op 4 cal pre-cal-nvmem max-sta 32 raw 0 hwcrypto 1
[   19.617882] ath10k_ahb a800000.wifi: qca4019 hw1.0 target 0x01000000 chip_id 0x003b00ff sub 0000:0000
[   19.617976] ath10k_ahb a800000.wifi: kconfig debug 0 debugfs 1 tracing 0 dfs 1 testmode 0
[   19.629853] ath10k_ahb a800000.wifi: firmware ver 10.4b-ct-4019-fW-13-5ae337bb1 api 5 features mfp,peer-flow-ctrl,txstatus-noack,wmi-10.x-CT,ratemask-CT,regdump-CT,txrate-CT,flush-all-CT,pingpong-CT,ch-regs-CT,nop-CT,set-special-CT,tx-rc-CT,cust-stats-CT,txrate2-CT,beacon-cb-CT,wmi-block-ack-CT,wmi-bcn-rc-CT crc32 6b2b5c5b
[   19.701228] ath10k_ahb a800000.wifi: board_file api 2 bmi_id 0:21 crc32 2d972a4b
[   20.997423] ath10k_ahb a800000.wifi: 10.4 wmi init: vdevs: 16  peers: 48  tid: 96
[   20.997501] ath10k_ahb a800000.wifi: msdu-desc: 2500  skid: 32
[   21.044696] ath10k_ahb a800000.wifi: wmi print 'P 48/48 V 16 K 144 PH 176 T 186  msdu-desc: 2500  sw-crypt: 0 ct-sta: 0'
[   21.045636] ath10k_ahb a800000.wifi: wmi print 'free: 53252 iram: 13432 sram: 35752'
[   21.181758] ath10k_ahb a800000.wifi: htt-ver 2.2 wmi-op 6 htt-op 4 cal pre-cal-nvmem max-sta 32 raw 0 hwcrypto 1
[   21.306645] usbcore: registered new interface driver option
[   21.306790] usbserial: USB Serial support registered for GSM modem (1-port)
[   21.311681] option 2-1:1.2: GSM modem (1-port) converter detected
[   21.318355] usb 2-1: GSM modem (1-port) converter now attached to ttyUSB0
[   21.324750] option 2-1:1.3: GSM modem (1-port) converter detected
[   21.331424] usb 2-1: GSM modem (1-port) converter now attached to ttyUSB1
[   21.337579] option 2-1:1.4: GSM modem (1-port) converter detected
[   21.344256] usb 2-1: GSM modem (1-port) converter now attached to ttyUSB2
[   21.353387] kmodloader: done loading kernel modules from /etc/modules.d/*
[   29.691269] ipqess-edma c080000.ethernet eth0: Link is Down
[   29.697596] ipqess-edma c080000.ethernet eth0: configuring for fixed/internal link mode
[   29.697911] ipqess-edma c080000.ethernet eth0: Link is Up - 1Gbps/Full - flow control rx/tx
[   29.703990] qca8k-ipq4019 c000000.switch lan: configuring for phy/psgmii link mode
[   29.714989] br-lan: port 1(lan) entered blocking state
[   29.720589] br-lan: port 1(lan) entered disabled state
[   29.725647] qca8k-ipq4019 c000000.switch lan: entered allmulticast mode
[   29.730785] ipqess-edma c080000.ethernet eth0: entered allmulticast mode
[   29.737828] qca8k-ipq4019 c000000.switch lan: entered promiscuous mode
[   29.768129] qca8k-ipq4019 c000000.switch wan: configuring for phy/psgmii link mode