ZyXEL Keenetic KN-1711 (Extra)
From TechInfoDepot
Jump to navigationJump to search
| abgn+ac (AC1200) | |
|---|---|
| AC1200 Mesh Wi-Fi 5 Router | |
|
| |
| Homepage | Product page |
| Wikipedia | ZyXEL |
| 3rd Party Firmware | |
| dd-wrt | Status Unknown |
| OpenWrt | Supported |
| Tomato any flavor | Incompatible |
| Gargoyle | Status Unknown |
| Platform | |
| Brand • Model • Rev | ZyXEL Keenetic KN-1711 (Extra) |
| FCC ID | none specified |
| Type | wireless router |
| CPU1 | MediaTek MT7628AN |
| CPU1 Type | MIPS 24KEc |
| CPU1 Speed | 580 MHz |
| Flash1 Chip | Winbond 25Q256JVFQ |
| Flash1 Size | 32 MiB33,554,432 B <br />262,144 Kib <br />32,768 KiB <br />256 Mib <br />0.0313 GiB <br /> (Dual Boot, SPI) |
| RAM1 Size | 128 MiB 134,217,728 B <br />1,048,576 Kib <br />131,072 KiB <br />1,024 Mib <br />0.125 GiB <br /> (DDR2) |
| RAM1 Chip | ESMT M14D1G1664A |
| ETH chip1 | MediaTek MT7628AN |
| Switch | MediaTek MT7628AN |
| Ethernet Port Count |
1-100MbE-WAN 4-100MbE-LAN |
| Wired Standard | IEEE 802.3i/3u |
|
802dot11 OUI: none specified | |
| Stock bootloader | U-Boot |
| Expansion IF types | USB 2.0 |
| USB ports | 1 |
| USB Hub Compatible | Untested |
| Power | 12 VDC, 1 A |
| Connector type | barrel |
| Serial Port (UART) | yes, 3.3V TTL, (115200 8N1) |
|
| |
|
| |
| Other | |
|
| |
| 3rd Party Firmware Support |
OpenWrt • (List | Dev | DLs) |
| Radio 1 | |
| Chip1 | MediaTek MT7603 |
| Wireless interface OUI | none specified |
| Antenna Connector Type | none specified |
| MIMO status | 2x2:2 |
| Wireless Standard | IEEE 802.11b/g/n |
| 802.11n | up to 300 Mbps |
| 802.11g | up to 54 Mbps |
| 802.11b | up to 11 Mbps |
| WiFi Operating Frequency | 2.4 GHz |
| Radio 2 | |
| Chip1 | MediaTek MT7613AEN |
| Wireless interface OUI | none specified |
| Antenna Connector Type | none specified |
| MIMO status | 2x2:2 |
| Wireless Standard | IEEE 802.11a/n/ac |
| 802.11ac | up to 867 Mbps |
| 802.11n | up to 300 Mbps |
| 802.11a | up to 54 Mbps |
| WiFi Operating Frequency | 5 GHz |
For a list of all currently documented MediaTek chipsets with specifications, see MediaTek.
For a list of all currently documented ZyXEL devices with specifications, see ZyXEL.
Flashing
| NOTE: During configuration or flashing a device, the only things that should be hooked to the device is the computer and power. |
Flashing OpenWrt
Target: ramips
Subtarget: mt76x8
Package architecture: mipsel_24kc
Supported Since Commit
Support started version: 25.12.0
Current supported version: 25.12.2
Subtarget: mt76x8
Package architecture: mipsel_24kc
Supported Since Commit
Support started version: 25.12.0
Current supported version: 25.12.2
Unsupported Functions:
DFS
LAN Hardware: MediaTek MT7628AN
WLAN Hardware: MediaTek MT7603 / MediaTek MT7613AEN
WLAN Comment: 2.4GHz: 2x2:2 MIMO, 5GHz: 2x2:2 MIMO
Installation method(s):
see git-commit
Recovery method(s):
see git-commit
DFS
LAN Hardware: MediaTek MT7628AN
WLAN Hardware: MediaTek MT7603 / MediaTek MT7613AEN
WLAN Comment: 2.4GHz: 2x2:2 MIMO, 5GHz: 2x2:2 MIMO
Installation method(s):
see git-commit
Recovery method(s):
see git-commit
| git • >> |
|---|
ramips: mt76x8: add support for Keenetic Extra (KN-1711) Specification: SoC: MediaTek MT7628AN RAM: 128 MB, ESMT M14D1G1664A (DDR2) Flash: 32MB, Winbond 25Q256JVFQ (Dual Boot, SPI) Switch: MediaTek MT7628AN, 5 ports 100 Mbps WiFi: MediaTek MT7603 2T2R/2.4GHz 802.11n and MediaTek MT7613AEN 2T2R/5GHz 802.11ac USB: 1 port USB 2.0 GPIO: 3 buttons (Wi-Fi, Reset, FN), 4 LEDs (Power, Internet, FN, Wi-Fi), USB port power controls Disassembly: At the bottom there are 4 screws hidden by rubber feet. After removing the screws, pry the gray plastic part around (it is secured with latches) and remove it. Serial Interface: The serial interface can be connected to the 4 pin dots to the left of the flash. Pins (from LEDs to LAN ports): 3.3V (do not connect) TX RX GND Settings: 115200, 8N1 Flashing via OEM recovery software: 1. Download the OEM recovery software from the manufacturer's website 2. Download the firmware image (for OpenWRT it is *-squashfs-factory.bin), rename it to KN-1711_recovery.bin 3. Replace the file in the fw folder OEM recovery software with the file from step 2. 4. Run the OEM recovery software and follow the instructions. Flashing via TFTP: 1. Connect your PC and router to port 1-4, configure PC interface using IP 192.168.1.2, mask 255.255.255.252 2. Serve the firmware image (for OpenWRT it is *-squashfs-factory.bin) renamed to KN-1711_recovery.bin via TFTP 3. Power up the router while pressing Reset button on the back 4. Release Restart button when Power LED starts blinking To revert back to OEM firmware: The return to the OEM firmware is carried out by using the methods described above with the help of the appropriate firmware image. When using OEM bootloader, the firmware image size cannot exceed the size of one OEM «Firmware_x» partition or Kernel + rootFS size. |
Categories:
- ZyXEL
- Keenetic
- Embedded system/wireless router
- Embedded System MediaTek
- Embedded System MT7628AN
- MediaTek
- Embedded System MIPS 24KEc
- Embedded System
- OpenWrt Supported
- Embedded System MT7603
- Has Mimo Status
- Embedded System IEEE 802.11b/g/n
- Embedded System MT7613AEN
- Embedded System IEEE 802.11a/n/ac
- Dual-Radio Wireless Embedded System
- Wireless Embedded System
- Dual-Band
- English Documentation