Elecom WRC-X3000GS3
From TechInfoDepot
(Redirected from ELECOM WRC-X3000GS3)
| abgn+ac+ax (AX3000) | |
|---|---|
| AX3000 Wi-Fi 6 Router | |
|
| |
| Homepage | Product page |
| WikiDevi.wi-cat.ru | Elecom WRC-X3000GS3 |
| 3rd Party Firmware | |
| dd-wrt | Status Unknown |
| OpenWrt | Supported |
| Tomato any flavor | Incompatible |
| Gargoyle | Status Unknown |
| Platform | |
| Brand • Model • Rev | Elecom WRC-X3000GS3 |
| FCC ID | none specified |
| Type | wireless router |
| CPU1 | MediaTek MT7981BA |
| CPU1 Type | ARM Cortex-A53 |
| CPU1 Speed | 1.3 GHz ( 2 cores ) 64-bit |
| Flash1 Chip | Winbond W25N01GVZEIG |
| Flash1 Size | 128 MiB 134,217,728 B <br />1,048,576 Kib <br />131,072 KiB <br />1,024 Mib <br />0.125 GiB <br /> (SPI NOR) |
| RAM1 Size | 512 MiB 536,870,912 B <br />4,194,304 Kib <br />524,288 KiB <br />4,096 Mib <br />0.5 GiB <br /> (DDR3) |
| RAM1 Chip | Winbond W634GU6QB-09 |
| ETH chip1 | MediaTek MT7981BA |
| Switch | MediaTek MT7531AE |
| Ethernet Port Count |
1-1GbE-WAN 4-1GbE-LAN |
| Wired Standard | IEEE 802.3i/3u/3ab |
| Stock bootloader | U-Boot |
| Expansion IF types | none specified |
| Power | 12 VDC, 1 A |
| Connector type | barrel |
| Serial Port (UART) | yes, 3.3, 115200 / 8N1 |
|
Flags: | |
|
| |
| Other | |
|
Default IP address: 192.168.2.1 | |
| Manuf/OEM/ODM | Elecom |
| 3rd Party Firmware Support |
OpenWrt • (List | Dev | DLs) |
| Retail | |
| Country of manuf | China |
| Radio 1 | |
| Chip1 | MediaTek MT7981BA |
| Chip2 | MediaTek MT7976CN |
| Wireless interface OUI | 38:97:A4 |
| Antenna Connector Type | none specified |
| MIMO status | 2x2:2 |
| Wireless Standard | IEEE 802.11b/g/n/ax |
| 802.11ax | up to 574 Mbps |
| 802.11n | up to 300 Mbps |
| 802.11g | up to 54 Mbps |
| 802.11b | up to 11 Mbps |
| WiFi Operating Frequency | 2.4 GHz |
| Radio 2 | |
| Chip1 | MediaTek MT7981BA |
| Chip2 | MediaTek MT7976CN |
| Wireless interface OUI | 38:97:A4 |
| Antenna Connector Type | none specified |
| MIMO status | 2x3:2 |
| Wireless Standard | IEEE 802.11a/n/ac/ax |
| AX-QAM | up to 2402 Mbps |
| 802.11ax | up to 1201 Mbps |
| 802.11ac | up to 867 Mbps |
| 802.11n | up to 300 Mbps |
| 802.11a | up to 54 Mbps |
| WiFi Operating Frequency | 5 GHz |
For a list of all currently documented MediaTek chipsets with specifications, see MediaTek.
For a list of all currently documented Elecom devices with specifications, see Elecom.
Flashing
| NOTE: During configuration or flashing a device, the only things that should be hooked to the device is the computer and power. |
Flashing OpenWrt
Target: mediatek
Subtarget: filogic
Package architecture: aarch64_cortex-a53
Supported Since Commit
Support started version: 25.12.0
Current supported version: 25.12.6
Subtarget: filogic
Package architecture: aarch64_cortex-a53
Supported Since Commit
Support started version: 25.12.0
Current supported version: 25.12.6
LAN Hardware: MediaTek MT7531A
WLAN Hardware: MediaTek MT7981B
WLAN Comment: 2.4/5 GHz 2T2R
Installation method(s):
see git-commit
Recovery method(s):
see git-commit
WLAN Hardware: MediaTek MT7981B
WLAN Comment: 2.4/5 GHz 2T2R
Installation method(s):
see git-commit
Recovery method(s):
see git-commit
| git • >> |
|---|
mediatek: add support for ELECOM WRC-X3000GS3
ELECOM WRC-X3000GS3 is a 2.4/5 GHz band 11ax (Wi-Fi 6) router, based on
MT7981B.
Specification:
- SoC : MediaTek MT7981B
- RAM : DDR3 512 MiB (Winbond W634GU6QB-09)
- Flash : SPI-NOR 128 MiB (Winbond W25N01GVZEIG)
- WLAN : 2.4/5 GHz 2T2R (MediaTek MT7981B (SoC))
- Ethernet : 5x 10/100/1000 Mbps
- wan (phy) : MediaTek MT7981B (SoC)
- lan (switch) : MediaTek MT7531A
- LEDs/Keys (GPIO): 8x/4x
- UART : through-hole on PCB (J500)
- assignment : 3.3V, TX, RX, NC, GND from tri-angle marking
- settings : 115200n8
- Power : 12 VDC, 1 A (Max. 12.8 W)
Flash instruction using factory.bin image:
1. Boot WRC-X3000GS3 in router mode normally
2. Access to the WebUI ("http://192.168.2.1/") on the device and open
the firmware update page ("ファームウェア更新")
3. Select the OpenWrt factory.bin image and click apply ("適用") button
4. Wait ~120 seconds to complete flashing
Switching to the stock firmware:
1. Load the elecom.sh script
. /lib/upgrade/elecom.sh
2. Check the current index of firmware partition
mstc_rw_bootnum
3. Set the bootnum to opposite value between 1 and 2
mstc_rw_bootnum <value>
example:
- step2 returned "1": mstc_rw_bootnum 2
- step2 returned "2": mstc_rw_bootnum 1
4. Reboot
Notes:
- ELECOM sells (or sold) multiple models as AX3000 class with different
hardwares:
- WRC-X3000GS(N) : Lantiq(Intel) GRX350/GRX550
- WRC-X3000GS(T)2: Qualcomm IPQ5018
- WRC-X3000GS3 : MediaTek MT7981B
MAC Addresses:
LAN : 38:97:A4:xx:xx:40 (Factory, 0x2A(hex)/Ubootenv,"ethaddr"(text))
WAN : 38:97:A4:xx:xx:43 (Factory, 0x24(hex))
2.4GHz: 38:97:A4:xx:xx:41 (Factory, 0x4 (hex))
5GHz : 38:97:A4:xx:xx:42 (Factory, 0xA (hex))
Signed-off-by: INAGAKI Hiroshi
Link: https://github.com/openwrt/openwrt/pull/18976
Signed-off-by: Hauke Mehrtens
|
Categories:
- Elecom
- Embedded system/wireless router
- Embedded System MediaTek
- Embedded System MT7981BA
- MediaTek
- Embedded System ARM
- Embedded System Cortex-A53
- Embedded System MT7531AE
- Manuf Elecom
- OpenWrt Supported
- Embedded System MT7976CN
- Has Mimo Status
- Embedded System IEEE 802.11b/g/n/ax
- Embedded System IEEE 802.11a/n/ac/ax
- Dual-Radio Wireless Embedded System
- Wireless Embedded System
- Dual-Band
- Embedded System
- English Documentation