Edimax BR-6478AC/Serial info
From TechInfoDepot
Jump to navigationJump to search
Info derived from
| boot log |
|---|
Booting...
@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@
@
@ chip__no chip__id mfr___id dev___id cap___id size_sft dev_size chipSize
@ 0000000h 0c22016h 00000c2h 0000020h 0000016h 0000000h 0000016h 0400000h
@ blk_size blk__cnt sec_size sec__cnt pageSize page_cnt chip_clk chipName
@ 0010000h 0000040h 0001000h 0000400h 0000100h 0000010h 000002dh MX25L3205D
@
@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@
---RealTek(RTL8196D)at 2013.01.02-14:19+0800 v0.6 [16bit](659MHz)
no rootfs signature at 000E0000!
no rootfs signature at 000F0000!
Jump to image start=0x80500000...
decompressing kernel:
Uncompressing Linux... done, booting the kernel.
done decompressing kernel.
start address: 0x80003470
CPU revision is: 0000dc02
Determined physical RAM map:
memory: 04000000 @ 00000000 (usable)
Zone PFN ranges:
Normal 0x00000000 -> 0x00004000
Movable zone start PFN for each node
early_node_map[1] active PFN ranges
0: 0x00000000 -> 0x00004000
Built 1 zonelists in Zone order, mobility grouping on. Total pages: 16256
Kernel command line: console=ttyS0,38400 root=/dev/mtdblock1
icache: 64kB/32B, dcache: 32kB/32B, scache: 0kB/0B
NR_IRQS:48
PID hash table entries: 256 (order: 8, 1024 bytes)
console handover: boot [early0] -> real [ttyS0]
Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
Memory: 49936k/65536k available (2692k kernel code,
15524k reserved, 712k data, 108k init, 0k highmem)
Calibrating delay loop... 658.63 BogoMIPS (lpj=3293184)
Mount-cache hash table entries: 512
net_namespace: 528 bytes
NET: Registered protocol family 16
bio: create slab <bio-0> at 0
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 2048 (order: 2, 16384 bytes)
TCP bind hash table entries: 2048 (order: 1, 8192 bytes)
TCP: Hash tables configured (established 2048 bind 2048)
TCP reno registered
NET: Registered protocol family 1
squashfs: version 4.0 (2009/01/31) Phillip Lougher
fuse init (API version 7.11)
msgmni has been set to 97
io scheduler noop registered
io scheduler cfq registered (default)
Realtek GPIO Driver for Flash Reload Default
Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled
serial8250: ttyS0 at MMIO 0x18002000 (irq = 8) is a 16550A
PPP generic driver version 2.4.2
MPPE/MPPC encryption/compression module registered
NET: Registered protocol family 24
PPPoL2TP kernel driver, V1.0
Realtek WLAN driver - version 1.6 (2013-02-21)
wlan_index:0 0, 134,0xba000000,0xb8b30000,14
=====>>INSIDE rtl8192cd_init_one <<=====
PCIE reset (0)
Do MDIO_RESET
Find Port=1 Device:Vender ID=881210ec
vendor_deivce_id=881210ec
found 8812 !!!
8812 mp chip !!
wlan0 (): not using net_device_ops yet
wlan0-wds0 (): not using net_device_ops yet
wlan0-wds1 (): not using net_device_ops yet
wlan0-wds2 (): not using net_device_ops yet
wlan0-wds3 (): not using net_device_ops yet
wlan0-wds4 (): not using net_device_ops yet
wlan0-wds5 (): not using net_device_ops yet
wlan0-wds6 (): not using net_device_ops yet
wlan0-wds7 (): not using net_device_ops yet
=====>>EXIT rtl8192cd_init_one <<=====
=====>>INSIDE rtl8192cd_init_one <<=====
wlan0-vxd (): not using net_device_ops yet
=====>>EXIT rtl8192cd_init_one <<=====
=====>>INSIDE rtl8192cd_init_one <<=====
wlan0-va0 (): not using net_device_ops yet
=====>>EXIT rtl8192cd_init_one <<=====
=====>>INSIDE rtl8192cd_init_one <<=====
wlan0-va1 (): not using net_device_ops yet
=====>>EXIT rtl8192cd_init_one <<=====
=====>>INSIDE rtl8192cd_init_one <<=====
wlan0-va2 (): not using net_device_ops yet
=====>>EXIT rtl8192cd_init_one <<=====
=====>>INSIDE rtl8192cd_init_one <<=====
wlan0-va3 (): not using net_device_ops yet
=====>>EXIT rtl8192cd_init_one <<=====
wlan_index:1 0, 134,0xb9000000,0xb8b10000,11
=====>>INSIDE rtl8192cd_init_one <<=====
PCIE reset (0)
Do MDIO_RESET
Find Port=0 Device:Vender ID=819110ec
vendor_deivce_id=819110ec
wlan1 (): not using net_device_ops yet
wlan1-wds0 (): not using net_device_ops yet
wlan1-wds1 (): not using net_device_ops yet
wlan1-wds2 (): not using net_device_ops yet
wlan1-wds3 (): not using net_device_ops yet
wlan1-wds4 (): not using net_device_ops yet
wlan1-wds5 (): not using net_device_ops yet
wlan1-wds6 (): not using net_device_ops yet
wlan1-wds7 (): not using net_device_ops yet
=====>>EXIT rtl8192cd_init_one <<=====
=====>>INSIDE rtl8192cd_init_one <<=====
wlan1-vxd (): not using net_device_ops yet
=====>>EXIT rtl8192cd_init_one <<=====
=====>>INSIDE rtl8192cd_init_one <<=====
wlan1-va0 (): not using net_device_ops yet
=====>>EXIT rtl8192cd_init_one <<=====
=====>>INSIDE rtl8192cd_init_one <<=====
wlan1-va1 (): not using net_device_ops yet
=====>>EXIT rtl8192cd_init_one <<=====
=====>>INSIDE rtl8192cd_init_one <<=====
wlan1-va2 (): not using net_device_ops yet
=====>>EXIT rtl8192cd_init_one <<=====
=====>>INSIDE rtl8192cd_init_one <<=====
wlan1-va3 (): not using net_device_ops yet
=====>>EXIT rtl8192cd_init_one <<=====
pwlan0 (): not using net_device_ops yet
Probing RTL8186 10/100 NIC-kenel stack size order[3]...
chip name: 8196C, chip revid: 0
NOT YET
-----share pin reg back to gpio mode-----
eth0 (): not using net_device_ops yet
eth0 added. vid=9 Member port 0x1...
eth1 (): not using net_device_ops yet
eth1 added. vid=8 Member port 0x10...
eth2 (): not using net_device_ops yet
eth2 added. vid=9 Member port 0x2...
eth3 (): not using net_device_ops yet
eth3 added. vid=9 Member port 0x4...
eth4 (): not using net_device_ops yet
eth4 added. vid=9 Member port 0x8...
eth7 (): not using net_device_ops yet
eth5 added. vid=9 Member port 0x0...
peth0 (): not using net_device_ops yet
[peth0] added, mapping to [eth1]...
SPI INIT
------------------------- Force into Single IO Mode ------------------------
|No chipID Sft chipSize blkSize secSize pageSize sdCk opCk chipName |
| 0 c22016h 0h 400000h 10000h 1000h 100h 50 0 MX25L3206E|
----------------------------------------------------------------------------
SPI flash(MX25L3206E) was found at CS0, size 0x400000
Creating 2 MTD partitions on "flash_bank_1":
0x000000000000-0x000000400000 : "boot+cfg+linux"
0x000000130000-0x000000400000 : "root fs"
Netfilter messages via NETLINK v0.30.
nf_conntrack version 0.5.0 (1024 buckets, 4096 max)
CONFIG_NF_CT_ACCT is deprecated and will be removed soon. Please use
nf_conntrack.acct=1 kernel paramater, acct=1 nf_conntrack module option or
sysctl net.netfilter.nf_conntrack_acct=1 to enable it.
xt_time: kernel timezone is -0000
ip_tables: (C) 2000-2006 Netfilter Core Team
TCP cubic registered
NET: Registered protocol family 17
dnshijack
Netlink[Kernel] create socket for igmp ok.
Realtek FastPath:v1.03
VFS: Mounted root (squashfs filesystem) readonly on device 31:1.
Freeing unused kernel memory: 108k freed
init started: BusyBox v1.11.1 (2013-10-31 22:06:17 CST)
starting pid 17, tty '': '/etc/init.d/rcS'
mount: mounting none on /dev/pts failed: No such device
insmod: cannot insert '/bin/islpci.o': Cannot allocate memory
starting pid 22, tty '': '-/bin/sh' console.
BusyBox v1.11.1 (2013-10-31 22:06:17 CST) built-in shell (ash)
Enter 'help' for a list of built-in commands.
/bin/init.sh: line 82: cannot create /proc/sw_nat: nonexistent directory
flash default
==> Flash Default <==
==> init WAN MTU
kill: you need to specify whom to kill
Close Wan Interface!!
==> WAN MTU 1500
********************************************
*
* Initialize wlan0 interface
*
********************************************
----> set 5G interface=wlan0
==> Set Tx power high level
==>US and EUR middle+high use US Table
set 5G TX Power: 0
C1: 0 txpower.sh
5G wlan0 MIB SYNC!
5G wlan0 init done!
********************************************
*
* Initialize wlan1 interface
*
********************************************
-----> IsVAP=wlan1 VAP=
==> Set Tx power high level
==>US and EUR middle+high use US Table
set 2.4G TX Power: 0
A1: 0 B1: 0 C1: 0 txpower.sh
Setup BRIDGE interface
==> Router bridge
==> COMMAND:bridge.sh br0 eth0 wlan0 wlan1 wlan0-va0 wlan0-va1
wlan0-va2 wlan0-va3 wlan1-va0 wlan1-va1 wlan1-va2 wlan1-va3
ifconfig: ioctl 0x8913 failed: No such device
ifconfig: ioctl 0x8913 failed: No such device
bridge br0 doesn't exist; can't delete it
Setup bridge...
device eth0 entered promiscuous mode
device wlan0 entered promiscuous mode
CP: MacInit_8812===>>=====>LLT_table_init_8812
LLT_table_init_8812<=====
BEQ_DESA = 0x0043f000 0x0043f000
DONE
[PHY_ConfigMACWithParaFile][MAC_REG_8812_n]
[PHY_ConfigBBWithParaFile][PHY_REG_8812_n_extlna]
[PHY_ConfigBBWithParaFile][PHY_REG_PG_8812_new]
[PHY_ConfigBBWithParaFile][AGC_TAB_8812_n_extlna]
[phy_RF6052_Config_ParaFile][RadioA_8812_n_extlna]
[phy_RF6052_Config_ParaFile][RadioB_8812_n_extlna]
<=== FirmwareDownload8812()
[PHY_ConfigTXPwrTrackingWithParaFile][REG_TXPWR_TRK_8812]
0x55d = 0x1
8812 Enable Tx 2 Path
0x838 B(1)= 0, 0x456 = 0x32
device wlan1 entered promiscuous mode
[PHY_ConfigMACWithParaFile][MACPHY_REG_92C]
===> Load_92C_Firmware
<=== Load_92C_Firmware
[PHY_ConfigTXPwrTrackingWithParaFile][REG_TXPWR_TRK]
0x55d = 0xff
br0: port 3(wlan1) entering forwarding state
br0: port 2(wlan0) entering forwarding state
br0: port 1(eth0) entering forwarding state
Static DHCP Leases disable!
br0: port 1(eth0) entering disabled state
br0: port 1(eth0) entering forwarding state
Setup WAN interface
kill: you need to specify whom to kill
Close Wan Interface!!
-->WAN_MODE:0
device eth1 is not a slave of br0
device eth0 is already a member of a bridge; can't enslave it to bridge br0.
**********************************************************************
* Enable WSC_UPnP *
**********************************************************************
**********************************************************************
* Enable LLTD *
**********************************************************************
**********************************************************************
* Enable GPIO Interrupt *
**********************************************************************
udhcpc (v1.11.1) started
into eth1.deconfig
killall: radiusd: no process killed
RADIUS server disable !!
killall: webs: no process killed
Generated PIN = 48751384
WiFi Simple Config v2.12.1-wps2.0 (2013.07.26-03:42+0000).
Register to wlan1
Register to wlan0
route: ioctl 0x890c failed: No such process
iwcontrol RegisterPID to (wlan1)
iwcontrol RegisterPID to (wlan0)
**********************************************************************
* FREE Page,Dentries and Inodes Cache *
**********************************************************************
IEEE 802.11f (IAPP) using interface br0 (v1.8)
MemFree: 36460 kB
Cached: 2344 kB
dns_hijack_enabled = 1
killall: nbnsd: no process killed
--iQsetup_set--
kill: you need to specify whom to kill
addcgiext .lua,.lp,.php
axhttpd/1.4.9: listening on ports 80 (http) and 443 (https)
iptables: No chain/target/match by that name.
iptables: No chain/target/match by that name.
--iQsetup set done--
No dnrd daemon found. Exiting.
Notice: caching turned off
ping: sendto: Network is unreachable
kill: you need to specify whom to kill
Notice: caching turned off
ping: sendto: Network is unreachable
boa: server version Boa/0.94.14rc21
boa: server built Oct 31 2013 at 22:06:10.
boa: starting server pid=1978, port 80
Run check_iqv2_work
|
Flash Information
Address Layout:
| 0x0 | Bootloader |
| 0x6000 | Flash Hardware settings |
| 0x8000 | Flash Default Settings |
| 0x10000 | Linux image flash offset start |
| 0x40000 | Linux image flash offset end |
| 0xE0000 | Root image offset start |
| 0x150000 | Root image offset end |
| 0x400000 | End of 4096KB flash |
There's a datasheet for the flash used: MX25L3206E