LUXUL ABR-4400/Serial info

Arrow Linux version 3.10.49 (dhaab@Kvasir) (gcc version 4.8.3 (OpenWrt/Linaro GCC 4.8-2014.04 r45315) ) #73 Mon Feb 13 17:43:53 MST 2017

Arrow BCM4706 Arrow M25FL128

Below the actual boot up from the console port

boot log • >>

Decompressing...done CFE version 6.30.102.9 (r366174) based on BBP 1.0.37 for BCM947XX (32bit,SP,LE) Build Date: Fri Dec 27 13:04:49 MST 2013 (dhaab@RabidWeaselCFE) Copyright (C) 2000-2008 Broadcom Corporation. Init Arena Init Devs. Boot partition size = 262144(0x40000) bcm_robo_enable_switch: EEE is enabled et0: Broadcom BCM47XX 10/100/1000 Mbps Ethernet Controller 6.30.102.9 (r366174) CPU type 0x19749: 600MHz Tot mem: 131072 KBytes CFE mem: 0x80700000 - 0x8079D8E0 (645344) Data: 0x807333D0 - 0x80736670 (12960) BSS: 0x80736670 - 0x807378E0 (4720) Heap: 0x807378E0 - 0x8079B8E0 (409600) Stack: 0x8079B8E0 - 0x8079D8E0 (8192) Text: 0x80700000 - 0x807333CC (209868) Device eth0: hwaddr A4-13-4E-10-D2-40, ipaddr 192.168.1.1, mask 255.255.255.0 gateway not set, nameserver not set Loader:raw Filesys:raw Dev:flash0.os File: Options:(null) Loading: .. 3712 bytes read Entry at 0x80001000 Closing network. Starting program at 0x80001000 [ 0.000000] Linux version 3.10.49 (dhaab@Kvasir) (gcc version 4.8.3 (OpenWrt/Linaro GCC 4.8-2014.04 r45315) ) #73 Mon Feb 13 17:43:53 MST 2017 [ 0.000000] CPU revision is: 00019749 (MIPS 74Kc) [ 0.000000] bcm47xx: using bcma bus [ 0.000000] bcma: bus0: Found chip with id 0x5300, rev 0x01 and package 0x00 [ 0.000000] bcma: bus0: Core 0 found: BCM4706 ChipCommon (manuf 0x4BF, id 0x500, rev 0x1F, class 0x0) [ 0.000000] bcma: bus0: Core 3 found: MIPS 74K (manuf 0x4A7, id 0x82C, rev 0x00, class 0x0) [ 0.000000] bcma: bus0: Found M25FL128 serial flash (size: 16384KiB, blocksize: 0x10000, blocks: 256) [ 0.000000] bcma: bus0: Early bus registered [ 0.000000] MIPS: machine is Luxul ABR-4400 V1 [ 0.000000] Determined physical RAM map: [ 0.000000] memory: 07fff000 @ 00000000 (usable) [ 0.000000] Initrd not found or empty - disabling initrd [ 0.000000] Zone ranges: [ 0.000000] Normal [mem 0x00000000-0x07ffefff] [ 0.000000] HighMem empty [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x00000000-0x07ffefff] [ 0.000000] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes. [ 0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 32511 [ 0.000000] Kernel command line: noinitrd console=ttyS0,115200 [ 0.000000] PID hash table entries: 512 (order: -1, 2048 bytes) [ 0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes) [ 0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes) [ 0.000000] Writing ErrCtl register=80000620 [ 0.000000] Readback ErrCtl register=80000620 [ 0.000000] Cache parity protection enabled [ 0.000000] Memory: 126540k/131068k available (2310k kernel code, 4528k reserved, 577k data, 176k init, 0k highmem) [ 0.000000] NR_IRQS:128 [ 0.000000] Setting up vectored interrupts [ 0.070000] Calibrating delay loop... 299.82 BogoMIPS (lpj=1499136) [ 0.070000] pid_max: default: 32768 minimum: 301 [ 0.070000] Mount-cache hash table entries: 512 [ 0.070000] NET: Registered protocol family 16 [ 0.080000] bio: create slab <bio-0> at 0 [ 0.080000] bcma: bus0: Core 1 found: BCM4706 GBit MAC (manuf 0x4BF, id 0x52D, rev 0x00, class 0x0) [ 0.080000] bcma: bus0: Core 2 found: BCM4706 GBit MAC (manuf 0x4BF, id 0x52D, rev 0x00, class 0x0) [ 0.080000] bcma: bus0: Core 4 found: USB 2.0 Host (manuf 0x4BF, id 0x819, rev 0x04, class 0x0) [ 0.080000] bcma: bus0: Core 5 found: PCIe (manuf 0x4BF, id 0x820, rev 0x0E, class 0x0) [ 0.080000] bcma: bus0: Core 6 found: PCIe (manuf 0x4BF, id 0x820, rev 0x0E, class 0x0) [ 0.080000] bcma: bus0: Core 7 found: AMEMC (DDR) (manuf 0x4BF, id 0x52E, rev 0x00, class 0x0) [ 0.080000] bcma: bus0: Core 8 found: BCM4706 SOC RAM (manuf 0x4BF, id 0x50E, rev 0x05, class 0x0) [ 0.080000] bcma: bus0: Core 9 found: ALTA (I2S) (manuf 0x4BF, id 0x534, rev 0x00, class 0x0) [ 0.080000] bcma: bus0: Core 10 found: BCM4706 GBit MAC Common (manuf 0x43B, id 0x5DC, rev 0x00, class 0x0) [ 0.090000] bcma: bus0: PCIEcore in host mode found [ 0.290000] PCI host bridge to bus 0000:00 [ 0.290000] pci_bus 0000:00: root bus resource [mem 0x08000000-0x0bffffff] [ 0.290000] pci_bus 0000:00: root bus resource [io 0x0100-0x047f] [ 0.290000] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff] [ 0.290000] bcma: PCI: Fixing up bridge 0000:00:00.0 [ 0.290000] bcma: PCI: Fixing up device 0000:00:00.0 [ 0.290000] bcma: PCI: Fixing up bridge 0000:00:00.1 [ 0.290000] bcma: PCI: Fixing up device 0000:00:00.1 [ 0.290000] bcma: bus0: PCIEcore in host mode found [ 0.490000] PCI host bridge to bus 0000:01 [ 0.490000] pci_bus 0000:01: root bus resource [mem 0x40000000-0x43ffffff] [ 0.490000] pci_bus 0000:01: root bus resource [io 0x0480-0x07ff] [ 0.490000] pci_bus 0000:01: No busn resource found for root bus, will use [bus 01-ff] [ 0.490000] bcma: PCI: Fixing up bridge 0000:01:00.0 [ 0.490000] bcma: PCI: Fixing up device 0000:01:00.0 [ 0.490000] bcma: PCI: Fixing up bridge 0000:01:00.1 [ 0.490000] bcma: PCI: Fixing up device 0000:01:00.1 [ 0.490000] bcma: bus0: Bus registered [ 0.490000] Switching to clocksource MIPS [ 0.500000] NET: Registered protocol family 2 [ 0.500000] TCP established hash table entries: 1024 (order: 1, 8192 bytes) [ 0.500000] TCP bind hash table entries: 1024 (order: 0, 4096 bytes) [ 0.500000] TCP: Hash tables configured (established 1024 bind 1024) [ 0.500000] TCP: reno registered [ 0.500000] UDP hash table entries: 256 (order: 0, 4096 bytes) [ 0.500000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes) [ 0.500000] NET: Registered protocol family 1 [ 0.500000] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 0.500000] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc. [ 0.500000] msgmni has been set to 247 [ 0.500000] io scheduler noop registered [ 0.500000] io scheduler deadline registered (default) [ 0.500000] Serial: 8250/16550 driver, 2 ports, IRQ sharing enabled [ 0.520000] serial8250.0: ttyS0 at MMIO 0xb8000300 (irq = 2) is a U6_16550A [ 1.010000] console [ttyS0] enabled [ 1.030000] serial8250.0: ttyS1 at MMIO 0xb8000400 (irq = 2) is a U6_16550A [ 1.210000] 6 bcm47xxpart partitions found on MTD device bcm47xxsflash [ 1.220000] Creating 6 MTD partitions on "bcm47xxsflash": [ 1.220000] 0x000000000000-0x000000040000 : "boot" [ 1.230000] 0x000000040000-0x000000ff0000 : "firmware" [ 1.240000] 0x00000004001c-0x00000004090c : "loader" [ 1.240000] 0x00000004090c-0x000000147800 : "linux" [ 1.250000] mtd: partition "linux" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only [ 1.260000] 0x000000147800-0x000000ff0000 : "rootfs" [ 1.270000] mtd: partition "rootfs" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only [ 1.280000] mtd: device 4 (rootfs) set to be root filesystem [ 1.290000] mtd: partition "rootfs_data" created automatically, ofs=0x700000, len=0x8f0000 [ 1.300000] 0x000000700000-0x000000ff0000 : "rootfs_data" [ 1.300000] 0x000000ff0000-0x000001000000 : "nvram" [ 1.310000] bcm47xxnflash: Chip reset not implemented yet [ 1.320000] bcm47xxnflash: Requested invalid id_data: 32 [ 1.320000] No NAND device found [ 1.330000] bcm47xxnflash: Could not scan NAND flash: -19 [ 1.330000] bcm47xxnflash: Initialization failed: -19 [ 1.340000] bgmac bcma0:0: Found PHY addr: 30 (NOREGS) [ 1.350000] bgmac bcma0:0: Support for Roboswitch not implemented [ 1.350000] libphy: bgmac mii bus: probed [ 1.430000] b53_common: found switch: BCM53125, rev 4 [ 1.440000] bgmac: Broadcom 47xx GBit MAC driver loaded [ 1.440000] bcm47xx-wdt bcm47xx-wdt.0: BCM47xx Watchdog Timer enabled (30 seconds) [ 1.450000] TCP: cubic registered [ 1.460000] NET: Registered protocol family 17 [ 1.460000] 8021q: 802.1Q VLAN Support v1.8 [ 1.470000] VFS: Mounted root (squashfs filesystem) readonly on device 31:4. [ 1.480000] Freeing unused kernel memory: 176K (802d4000 - 80300000) procd: Console is alive procd: - watchdog - [ 3.730000] pps_core: LinuxPPS API ver. 1 registered [ 3.730000] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it> [ 3.740000] PTP clock support registered [ 3.770000] usbcore: registered new interface driver usbfs [ 3.780000] usbcore: registered new interface driver hub [ 3.790000] usbcore: registered new device driver usb [ 3.800000] SCSI subsystem initialized [ 3.810000] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 3.820000] ohci-platform ohci-platform.0: Generic Platform OHCI Controller [ 3.830000] ohci-platform ohci-platform.0: new USB bus registered, assigned bus number 1 [ 3.830000] ohci-platform ohci-platform.0: irq 6, io mem 0x18009000 [ 3.900000] hub 1-0:1.0: USB hub found [ 3.900000] hub 1-0:1.0: 2 ports detected [ 3.910000] uhci_hcd: USB Universal Host Controller Interface driver [ 3.920000] usbcore: registered new interface driver usb-storage procd: - preinit - Failsafe has been disabled jffs2 is ready No jffs2 marker was found [ 4.650000] jffs2: notice: (221) jffs2_build_xattr_subsystem: complete building xattr subsystem, 29 of xdatum (0 unchecked, 28 orphan) and 101 of xref (0 dead, 87 orphan) found. switching to overlay procd: - early - procd: - watchdog - procd: - ubus - procd: - init - Please press Enter to activate this console. [ 8.930000] NET: Registered protocol family 10 [ 8.940000] Initializing XFRM netlink socket [ 8.950000] NET: Registered protocol family 15 [ 8.960000] luxulctf: module license 'unspecified' taints kernel. [ 8.960000] Disabling lock debugging due to kernel taint [ 8.970000] luxulctf: version 1.10 loaded (current state: OFF) [ 8.980000] tun: Universal TUN/TAP device driver, 1.6 [ 8.980000] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com> [ 9.020000] l2tp_core: L2TP core driver, V2.0 [ 9.030000] l2tp_netlink: L2TP netlink interface [ 9.050000] gre: GRE over IPv4 demultiplexor driver [ 9.060000] ip_gre: GRE over IPv4 tunneling driver [ 9.080000] nf_conntrack version 0.5.0 (1979 buckets, 7916 max) [ 9.100000] ip6_tables: (C) 2000-2006 Netfilter Core Team [ 9.380000] Netfilter messages via NETLINK v0.30. [ 9.400000] ip_set: protocol 6 [ 9.460000] u32 classifier [ 9.460000] input device check on [ 9.460000] Actions configured [ 9.470000] Mirror/redirect action on [ 9.480000] ip_tables: (C) 2000-2006 Netfilter Core Team [ 9.550000] usbcore: registered new interface driver ums-alauda [ 9.560000] usbcore: registered new interface driver ums-cypress [ 9.570000] usbcore: registered new interface driver ums-datafab [ 9.580000] usbcore: registered new interface driver ums-freecom [ 9.590000] usbcore: registered new interface driver ums-isd200 [ 9.600000] usbcore: registered new interface driver ums-jumpshot [ 9.610000] usbcore: registered new interface driver ums-karma [ 9.620000] usbcore: registered new interface driver ums-sddr09 [ 9.630000] usbcore: registered new interface driver ums-sddr55 [ 9.640000] usbcore: registered new interface driver ums-usbat [ 9.650000] usbcore: registered new interface driver usblp [ 9.710000] xt_time: kernel timezone is -0000 [ 9.730000] PPP generic driver version 2.4.2 [ 9.740000] PPP MPPE Compression module registered [ 9.750000] NET: Registered protocol family 24 [ 9.760000] PPTP driver version 0.8.5 [ 9.770000] l2tp_ppp: PPPoL2TP kernel driver, V2.0 [ 14.700000] libphy: bgmac-0-0:1e - Link is Up - 1000/Full [ 15.220000] device eth0.1 entered promiscuous mode [ 15.230000] device eth0 entered promiscuous mode [ 15.240000] br-lan: port 1(eth0.1) entered forwarding state [ 15.240000] br-lan: port 1(eth0.1) entered forwarding state [ 16.760000] libphy: bgmac-0-0:1e - Link is Up - 1000/Full [ 17.240000] br-lan: port 1(eth0.1) entered forwarding state [ 23.000000] luxulctf: state changed to ON procd: - init complete -