Linksys EA7500/Serial info
From TechInfoDepot
Jump to navigationJump to search
Boot log
| Boot log • >> |
|---|
U-Boot .07 [Standard IPQ806X.LN,r40331] (Nov 05 2015 - 14:44:22)
CBT U-Boot ver: 1.1.4
smem ram ptable found: ver: 0 len: 5
DRAM: 235 MiB
NAND: SF: Unsupported manufacturer 00
ipq_spi: SPI Flash not found (bus/cs/speed/mode) = (0/0/48000000/0)
128 MiB
MMC:
PCI0 Link Intialized
PCI1 Link Intialized
In: serial
Out: serial
Err: serial
cdp: get part failed for 0:HLOS
Net: MAC1 addr:0:3:7f:ba:db:1
athrs17_reg_init: complete
athrs17_vlan_config ...done
S17c init done
MAC2 addr:0:3:7f:ba:db:2
eth0
Warning: eth0 MAC addresses don't match:
Address in SROM is 00:03:7f:ba:db:01
Address in environment is 00:06:3b:01:41:00
, eth1
Updating boot_count ... done
Hit any key to stop autoboot: 0
MMC Device 0 not found
MMC Device 0 not found
Loading from nand0, offset 0xf80000
Image Name: Linux-3.4.103
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 1897480 Bytes = 1.8 MiB
Load Address: 41508000
Entry Point: 41508000
Automatic boot of image at addr 0x44000000 ...
Image Name: Linux-3.4.103
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 1897480 Bytes = 1.8 MiB
Load Address: 41508000
Entry Point: 41508000
Verifying Checksum ... OK
Loading Kernel Image ... OK
OK
mtdids not defined, no default present
info: "mtdparts" not set
Using machid 0x1260 from environment
Starting kernel ...
[ 0.000000] Booting Linux on physical CPU 0
[ 0.000000] Linux version 3.4.103 (root@build-vm) (gcc version 4.6.3 20120201 (prerelease) (Linaro GCC 4.6-2012.02) ) #1 SMP PREEMPT Thu Feb 15 17:25:15 PST 2018
[ 0.000000] CPU: ARMv7 Processor [512f04d0] revision 0 (ARMv7), cr=10c5387d
[ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, PIPT instruction cache
[ 0.000000] Machine: Linksys EA7500 WiFi Router.
[ 0.000000] msm_reserve_memory: 0x44600000, 0x200000
[ 0.000000] memory pool 3 (start 4fc00000 size 400000) initialized
[ 0.000000] Memory policy: ECC disabled, Data cache writealloc
[ 0.000000] smem_find(137, 80): wrong size 72
[ 0.000000] socinfo_init: v6, id=202, ver=2.0, raw_id=2064, raw_ver=2064, hw_plat=0, hw_plat_ver=65536
[ 0.000000] accessory_chip=0 hw_plat_subtype=0
[ 0.000000] PERCPU: Embedded 8 pages/cpu @c0a4b000 s11072 r8192 d13504 u32768
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 58154
[ 0.000000] Kernel command line: console=ttyHSL1,115200n8 init=/sbin/init rootfstype=squashfs ubi.mtd=14,2048 ubi.block=0,0 root=/dev/ubiblock0_0 rootwait ro
[ 0.000000] PID hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
[ 0.000000] Memory: 49MB 180MB = 229MB total
[ 0.000000] Memory: 223660k/229804k available, 10836k reserved, 0K highmem
[ 0.000000] Virtual kernel memory layout:
[ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB)
[ 0.000000] fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB)
[ 0.000000] vmalloc : 0xcf000000 - 0xff000000 ( 768 MB)
[ 0.000000] lowmem : 0xc0000000 - 0xceb00000 ( 235 MB)
[ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB)
[ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB)
[ 0.000000] .text : 0xc0008000 - 0xc0519000 (5188 kB)
[ 0.000000] .init : 0xc0600000 - 0xc0702b40 (1035 kB)
[ 0.000000] .data : 0xc0704000 - 0xc07a1160 ( 629 kB)
[ 0.000000] .bss : 0xc07a1184 - 0xc0849e4c ( 676 kB)
[ 0.000000] SLUB: Genslabs=11, HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
[ 0.000000] Preemptible hierarchical RCU implementation.
[ 0.000000] NR_IRQS:1689
[ 0.000000] sched_clock: 32 bits at 32kHz, resolution 31240ns, wraps every 134175798ms
[ 0.000000] Console: colour dummy device 80x30
[ 0.150421] Calibrating delay using timer specific routine.. 12.55 BogoMIPS (lpj=62799)
[ 0.150452] pid_max: default: 32768 minimum: 301
[ 0.150921] Mount-cache hash table entries: 512
[ 0.152389] CPU: Testing write buffer coherency: ok
[ 0.152608] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
[ 0.152639] hw perfevents: enabled with ARMv7 Krait PMU driver, 5 counters available
[ 0.152764] Setting up static identity map for 0x418cbd80 - 0x418cbe08
[ 0.155076] CPU1: Booted secondary processor
[ 0.155139] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001
[ 0.155232] Brought up 2 CPUs
[ 0.155263] SMP: Total of 2 processors activated (25.11 BogoMIPS).
[ 0.171571] dummy:
[ 0.172258] NET: Registered protocol family 16
[ 0.173102] AXI: msm_bus_fabric_init_driver(): msm_bus_fabric_init_driver
[ 0.175413] meminfo_init: smem ram ptable found: ver: 0 len: 5
[ 0.175445] Found 1 memory banks grouped into 8 memory regions
[ 0.175757] gpiochip_add: registered GPIOs 0 to 151 on device: msmgpio
[ 0.176538] smem_find(137, 80): wrong size 72
[ 0.176569] socinfo_init: v6, id=202, ver=2.0, raw_id=2064, raw_ver=2064, hw_plat=0, hw_plat_ver=65536
[ 0.176569] accessory_chip=0 hw_plat_subtype=0
[ 0.176632] msm_rpm_init: RPM firmware 3.0.16777342
[ 0.184442] clk_tbl_nss - loaded
[ 0.211184] hw-breakpoint: found 5 (+1 reserved) breakpoint and 4 watchpoint registers.
[ 0.211184] hw-breakpoint: maximum watchpoint size is 8 bytes.
[ 0.211621] msm_dmov_memcpy_init: Success
[ 0.218712] sps:BAM 0x12244000 enabled: ver:0x5, number of pipes:20
[ 0.218744] sps:BAM 0x12244000 is registered.
[ 0.218994] sps:sps is ready.
[ 0.260855] msm_pcie_setup: link initialized
[ 0.261230] PCI host bridge to bus 0000:00
[ 0.261262] pci_bus 0000:00: root bus resource [mem 0x08000000-0x0fefffff]
[ 0.261793] PCI: bus0: Fast back to back transfers disabled
[ 0.261793] pci 0000:00:00.0: bridge configuration invalid ([bus 00-00]), reconfiguring
[ 0.262605] PCI: bus1: Fast back to back transfers disabled
[ 0.300968] msm_pcie_setup: link initialized
[ 0.301312] PCI host bridge to bus 0000:02
[ 0.301343] pci_bus 0000:02: root bus resource [mem 0x2e000000-0x31efffff]
[ 0.301811] PCI: bus2: Fast back to back transfers disabled
[ 0.301811] pci 0000:02:00.0: bridge configuration invalid ([bus 00-00]), reconfiguring
[ 0.302530] PCI: bus3: Fast back to back transfers disabled
[ 0.421305] msm_pcie_setup: link initialization failed
[ 0.421524] pci 0000:02:00.0: BAR 8: assigned [mem 0x2e000000-0x2e1fffff]
[ 0.421555] pci 0000:03:00.0: BAR 0: assigned [mem 0x2e000000-0x2e1fffff 64bit]
[ 0.421587] pci 0000:02:00.0: PCI bridge to [bus 03-03]
[ 0.421618] pci 0000:02:00.0: bridge window [mem 0x2e000000-0x2e1fffff]
[ 0.421680] PCI: enabling device 0000:02:00.0 (0140 -> 0143)
[ 0.421743] pci 0000:00:00.0: BAR 8: assigned [mem 0x08000000-0x081fffff]
[ 0.421774] pci 0000:01:00.0: BAR 0: assigned [mem 0x08000000-0x081fffff 64bit]
[ 0.421805] pci 0000:00:00.0: PCI bridge to [bus 01-01]
[ 0.421836] pci 0000:00:00.0: bridge window [mem 0x08000000-0x081fffff]
[ 0.421868] PCI: enabling device 0000:00:00.0 (0140 -> 0143)
[ 0.448391] bio: create slab <bio-0> at 0
[ 0.449953] SCSI subsystem initialized
[ 0.451827] spi_qsd spi_qsd.5: master is unqueued, this is deprecated
[ 0.454170] spi_qsd spi_qsd.6: master is unqueued, this is deprecated
[ 0.458481] Switching to clocksource gp_timer
[ 0.480537] NET: Registered protocol family 2
[ 0.490253] IP route cache hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.490877] TCP established hash table entries: 8192 (order: 4, 65536 bytes)
[ 0.490971] TCP bind hash table entries: 8192 (order: 4, 65536 bytes)
[ 0.491065] TCP: Hash tables configured (established 8192 bind 8192)
[ 0.491096] TCP: reno registered
[ 0.491096] UDP hash table entries: 128 (order: 0, 4096 bytes)
[ 0.491127] UDP-Lite hash table entries: 128 (order: 0, 4096 bytes)
[ 0.491565] NET: Registered protocol family 1
[ 0.492970] Detected 5 counters on the L2CC PMU.
[ 0.494001] smd: register irq failed on wcnss_a11
[ 0.494033] smd: deregistering IRQs
[ 0.494064] SMD: smd_core_platform_init() failed
[ 0.494814] Partition(from smem) SBL1 -- Offset:0 Size:2
[ 0.494845] Partition(from smem) MIBIB -- Offset:2 Size:a
[ 0.494845] Partition(from smem) SBL2 -- Offset:c Size:a
[ 0.494876] Partition(from smem) SBL3 -- Offset:16 Size:14
[ 0.494876] Partition(from smem) DDRCONFIG -- Offset:2a Size:9
[ 0.494907] Partition(from smem) SSD -- Offset:33 Size:9
[ 0.494907] Partition(from smem) TZ -- Offset:3c Size:14
[ 0.494939] Partition(from smem) RPM -- Offset:50 Size:14
[ 0.494970] Partition(from smem) ART -- Offset:64 Size:a
[ 0.494970] Partition(from smem) APPSBL -- Offset:6e Size:8
[ 0.495001] get_nand_partitions: partition name=rootfs found.
[ 0.495001] Overlaying Olympus partition
[ 0.495032] Olympus partition u_env -- Offset:76 Size:2
[ 0.495032] Olympus partition s_env -- Offset:78 Size:2
[ 0.495032] Olympus partition devinfo -- Offset:7a Size:2
[ 0.495064] Olympus partition kernel -- Offset:7c Size:140
[ 0.495064] Olympus partition rootfs -- Offset:94 Size:128
[ 0.495064] Olympus partition alt_kernel -- Offset:1bc Size:140
[ 0.495095] Olympus partition alt_rootfs -- Offset:1d4 Size:128
[ 0.495095] Olympus partition sysdiag -- Offset:2fc Size:8
[ 0.495095] Olympus partition syscfg -- Offset:304 Size:0
[ 0.495126] get_bootconfig_partition: magic not found
[ 0.508653] acpuclk-ipq806x acpuclk-ipq806x: SPEED BIN: 0
[ 0.508684] acpuclk-ipq806x acpuclk-ipq806x: ACPU PVS: 1
[ 0.515338] acpuclk-ipq806x acpuclk-ipq806x: CPU0: 6 frequencies supported
[ 0.515370] acpuclk-ipq806x acpuclk-ipq806x: CPU1: 6 frequencies supported
[ 0.516900] msm_rpm_log_probe: OK
[ 0.535363] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.535363] jffs2: version 2.2. (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) © 2001-2006 Red Hat, Inc.
[ 0.536707] msgmni has been set to 436
[ 0.538019] io scheduler noop registered
[ 0.538050] io scheduler deadline registered (default)
[ 0.540018] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
[ 0.543392] msm_serial_hs.0: ttyHS0 at MMIO 0x12490000 (irq = 227) is a MSM HS UART
[ 0.544048] msm_serial_hs module loaded
[ 0.544236] msm_serial_hsl: detected port #1
[ 0.544361] msm_serial_hsl.1: ttyHSL1 at MMIO 0x16340000 (irq = 184) is a MSM
[ 0.544798] msm_serial_hsl: console setup on port #1
[ 1.353108] console [ttyHSL1] enabled
[ 1.357200] msm_serial_hsl: driver initialized
[ 1.366135] ahci ahci.0: forcing PORTS_IMPL to 0x1
[ 1.369978] ahci ahci.0: AHCI 0001.0300 32 slots 1 ports 6 Gbps 0x1 impl platform mode
[ 1.377819] ahci ahci.0: flags: ncq sntf pm led clo only pmp pio slum part ccc apst
[ 1.386941] scsi0 : ahci_platform
[ 1.390034] ata1: SATA max UDMA/133 mmio [mem 0x29000000-0x2900017f] port 0x100 irq 241
[ 1.399875] msm_nand_probe: phys addr 0x1ac00000
[ 1.403530] msm_nand_probe: dmac 0x3
[ 1.407122] msm_nand_probe: allocated dma buffer at ffdfc000, dma_addr 4f5c0000
[ 1.415807] status: e00020
[ 1.417494] nandid: 1580a101 maker 01 device a1
[ 1.422524] ONFI probe : Found an ONFI compliant device S34MS01G2
[ 1.429303] Found a supported NAND device
[ 1.433114] NAND Controller ID : 0x4030
[ 1.436925] NAND Device ID : 0x1580a101
[ 1.440893] Buswidth : 8 Bits
[ 1.443798] Density : 128 MByte
[ 1.447016] Pagesize : 2048 Bytes
[ 1.450359] Erasesize: 131072 Bytes
[ 1.453764] Oobsize : 64 Bytes
[ 1.456888] CFG0 Init : 0xa8d408c0
[ 1.460418] CFG1 Init : 0x0004745c
[ 1.463855] ECCBUFCFG : 0x00000203
[ 1.468103] Creating 19 MTD partitions on "msm_nand":
[ 1.472414] 0x000000000000-0x000000040000 : "SBL1"
[ 1.480193] 0x000000040000-0x000000180000 : "MIBIB"
[ 1.488191] 0x000000180000-0x0000002c0000 : "SBL2"
[ 1.496126] 0x0000002c0000-0x000000540000 : "SBL3"
[ 1.505810] 0x000000540000-0x000000660000 : "DDRCONFIG"
[ 1.514214] 0x000000660000-0x000000780000 : "SSD"
[ 1.521868] 0x000000780000-0x000000a00000 : "TZ"
[ 1.531365] 0x000000a00000-0x000000c80000 : "RPM"
[ 1.541049] 0x000000c80000-0x000000dc0000 : "ART"
[ 1.549047] 0x000000dc0000-0x000000ec0000 : "APPSBL"
[ 1.556950] 0x000000ec0000-0x000000f00000 : "u_env"
[ 1.563730] 0x000000f00000-0x000000f40000 : "s_env"
[ 1.570509] 0x000000f40000-0x000000f80000 : "devinfo"
[ 1.577444] 0x000000f80000-0x000003780000 : "kernel"
[ 1.639362] 0x000001280000-0x000003780000 : "rootfs"
[ 1.697125] 0x000003780000-0x000005f80000 : "alt_kernel"
[ 1.738612] ata1: SATA link down (SStatus 0 SControl 300)
[ 1.763792] 0x000003a80000-0x000005f80000 : "alt_rootfs"
[ 1.820024] 0x000005f80000-0x000006080000 : "sysdiag"
[ 1.827772] 0x000006080000-0x000008000000 : "syscfg"
[ 1.877069] UBI: attaching mtd14 to ubi0
[ 1.880037] UBI: physical eraseblock size: 131072 bytes (128 KiB)
[ 1.886223] UBI: logical eraseblock size: 126976 bytes
[ 1.891721] UBI: smallest flash I/O unit: 2048
[ 1.896282] UBI: VID header offset: 2048 (aligned 2048)
[ 1.902311] UBI: data offset: 4096
[ 2.195220] UBI: max. sequence number: 2
[ 2.210871] UBI: attached mtd14 to ubi0
[ 2.213683] UBI: MTD device name: "rootfs"
[ 2.218806] UBI: MTD device size: 37 MiB
[ 2.223586] UBI: number of good PEBs: 296
[ 2.228178] UBI: number of bad PEBs: 0
[ 2.232677] UBI: number of corrupted PEBs: 0
[ 2.237050] UBI: max. allowed volumes: 128
[ 2.241674] UBI: wear-leveling threshold: 4096
[ 2.246329] UBI: number of internal volumes: 1
[ 2.250796] UBI: number of user volumes: 1
[ 2.255170] UBI: available PEBs: 0
[ 2.259731] UBI: total number of reserved PEBs: 296
[ 2.264479] UBI: number of PEBs reserved for bad PEB handling: 2
[ 2.270509] UBI: max/mean erase counter: 1/0
[ 2.274695] UBI: image sequence number: 1211679096
[ 2.279631] UBI: background thread "ubi_bgt0d" started, PID 668
[ 2.287191] UBI: ubiblock0_0 created from ubi0:0(squashfs)
[ 2.323711] GPIO Bitbanged MDIO: probed
[ 2.328928] PPP generic driver version 2.4.2
[ 2.332802] NET: Registered protocol family 24
[ 2.336644] PPTP driver version 0.8.5
[ 2.347141] cpuidle: using governor ladder
[ 2.350827] cpuidle: using governor menu
[ 2.356888] Netfilter messages via NETLINK v0.30.
[ 2.360824] nf_conntrack version 0.5.0 (3494 buckets, 13976 max)
[ 2.367478] ctnetlink v0.93: registering with nfnetlink.
[ 2.371946] nf_conntrack_rtsp v0.7 loading
[ 2.376038] ip_set: protocol 6
[ 2.379881] gre: GRE over IPv4 demultiplexor driver
[ 2.383848] ip_gre: GRE over IPv4 tunneling driver
[ 2.390721] nf_nat_rtsp v0.7 loading
[ 2.393345] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 2.399281] TCP: cubic registered
[ 2.403717] NET: Registered protocol family 10
[ 2.409934] ip6_tables: (C) 2000-2006 Netfilter Core Team
[ 2.414839] IPv6 over IPv4 tunneling driver
[ 2.422086] NET: Registered protocol family 17
[ 2.425741] Bridge firewalling registered
[ 2.429803] Ebtables v2.0 registered
[ 2.433239] L2TP core driver, V2.0
[ 2.436488] PPPoL2TP kernel driver, V2.0
[ 2.440424] L2TP netlink interface
[ 2.443798] 8021q: 802.1Q VLAN Support v1.8
[ 2.448172] VFP support v0.3: implementor 51 architecture 64 part 4d variant 2 rev 0
[ 2.455670] Registering SWP/SWPB emulation handler
[ 2.460481] clock_late_init: Removing enables held for handed-off clocks
[ 2.476132] ipq_nss_get_mac_addr: MAC[0]: ff:ff:ff:ff:ff:ff
[ 2.480974] ipq_nss_get_mac_addr: MAC[1]: ff:ff:ff:ff:ff:ff
[ 2.486472] ipq_nss_get_mac_addr: MAC[2]: ff:ff:ff:ff:ff:ff
[ 2.492064] ipq_nss_get_mac_addr: MAC[3]: ff:ff:ff:ff:ff:ff
[ 2.497532] no pmic restart interrupt specified
[ 2.503498] msm_cache_dump_probe: could not register L2 buffer ret = -22.
[ 2.513277] VFS: Mounted root (squashfs filesystem) readonly on device 254:0.
[ 2.520024] Freeing init memory: 1032K
*********************************************************************************
_ _ __ _ __ _____ __ __ _____
| | | || \ | | / // ____]\ \ / // ____]TM
| | | || \ | | / /| (___ \ V /| (____
| | | || |\ \| |\ \ \____ \ \ / \____ \
| |_____ | || | \ | \ \ ____) | | | ____) |
|_______||_||_| \__| \_\[____ / |_| [_____/
(c) 2013 Belkin International, Inc. and/or its affiliates. All rights reserved.
Booting macan (firmware version 1.1.4.186518)
*********************************************************************************
[utopia][init] System Initialization
[utopia][init] Creating /proc
[utopia][init] Creating /sys
[utopia][init] Creating /dev
[utopia][init] Creating /tmp
[utopia][init] Allocating 50M for /tmp
[utopia][init] Prepairing /dev/pts
[utopia][init] Setting /tmp and /var permissions
[utopia][init] Starting udev..
[ 3.171290] bdutil board utility kernel module, version 1.4
[ 3.176444] bdutil board utility kernel module boardId (0)
[ 3.181318] bdutil board utility LEDs kernel module, version 1.3
Attempting mount of ubifs syscfg partition
UBI device number 1, total 252 LEBs (31997952 bytes, 30.5 MiB), available 0 LEBs (0 bytes), LEB size 126976 bytes (124.0 KiB)
[utopia][init] Using persistent syscfg data from /var/config/syscfg
[utopia][init] Starting system logging
[utopia][init] Starting sysevent subsystem
[utopia][init] Enabling DesignWare USB3 DRD Core drivers
[utopia][init] Loading QCA NSS and GMAC drivers
net.netfilter.nf_conntrack_acct = 1
[utopia][init] Late loading usb drivers
[utopia][init] Setting any unset system values to default
[utopia][init] no persistence config file (/var/config/pstcfg) found
setting up MAC addresses for all interface based on C0:56:27:39:AA:B0
NTP Servers do not need to be updated
checking for interactive script start up...
Updating BootCount Page[6]:3000 ... Done
attempting to sync sysinfo.cgi auth credentials
[utopia][init] Loading LEDS and Buttons drivers
[utopia][init] Setup link to WiFi firmware and board data (EU)
[utopia][init] Using EU region for WiFi firmware and board data
NSS Auto scaling disabled
dev.nss.ipv4cfg.ipv4_conn = 4 GiB
dev.nss.ipv6cfg.ipv6_conn = 4 GiB
inserting ecm.ko and fpbypass.ko for QCA
Sat Mar 14 05:57:00 UTC 2020
macan login: wan, sysevent received: wan-start=NULL
Lighttpd Model Base: EA7500
Generating Rainier lighttpd config
Build temporary www configuration directory:
TSLIIHauhEfGE
wifi, sysevent received: lan-started (Sat Mar 14 06:57:05 CET 2020)
wifi, service_start()
Power cycle Ethernet ports.
[utopia][init] Loading GMAC and WLAN drivers
Registering Service myrouter._http._tcp.local port 80
Got a reply for myrouter._http._tcp.local.: Name now registered and active
[utopia][init] Creating wifi devices
ath0
ath1
[utopia][init] setting WiFi Red CE settings
wifi, wifi_physical_start(ath0)
wifi, setting obss rssi threshold (ath0)
Auto channel
wifi, wifi_virtual_start(ath0)
wifi, wifi_user_start(ath0)
wifi_user, ath0 TxBF enabled
wifi, primary AP: ath0 is up
wifi, wifi_guest_start(ath0)
wifi, guest ath2 is disabled, do not start wifi guest
wifi, wifi_physical_start(ath1)
wifi, setting obss rssi threshold (ath1)
wifi, wifi_virtual_start(ath1)
wifi, wifi_user_start(ath1)
Not ready for JNAP. Sleeping for 15 seconds...
iwconfig: unknown command "5"
wifi_user, ath1 TxBF enabled
wifi_user, ath1 MU-MIMO enabled
wifi, primary AP: ath1 is up
wifi, wifi_guest_start(ath1)
wifi, guest ath3 is disabled, do not start wifi guest
wifi, start_hostapd()
Configuration file: /tmp/hostapd-ath0.conf
Configuration file: /tmp/hostapd-ath1.conf
mediaserver got event: mediaserver-stop
ath0: Could not connect to kernel driver
Using interface ath0 with hwaddr c0:56:27:39:aa:b1 and ssid "Linksys"
ath0: interface state UNINITIALIZED->ENABLED
ath0: AP-ENABLED
ath1: Could not connect to kernel driver
Using interface ath1 with hwaddr c0:56:27:39:aa:b2 and ssid "Linksys 5"
ath1: interface state UNINITIALIZED->ENABLED
ath1: AP-ENABLED
[utopia] Not setting ppp_clamp_mtu
alljoyn service_init
fastpath, sysevent received: qos_enabled
Restarting nfqrecv service...
net.bridge.bridge-nf-call-ip6tables = 1
net.bridge.bridge-nf-call-iptables = 1
dev.nss.general.redirect = 1
[utopia] Not setting ppp_clamp_mtu on dslite protocol
udhcpc (v1.19.4) started
wan, sysevent received: phylink_wan_state=up
Sending discover...
Sending discover...
Sending select for 192.168.74.142...
Lease of 192.168.74.142 obtained, lease time 43200
device_registration: Received event: wan-started
Sat Mar 14 05:57:48 2020 xrac Device is not associated, exiting...
data_uploader service started
device_registration: Service started
mediaserver got event: mediaserver-stop
Starting smbd ...
[fw.sh] fwup_checked_after_boot: 0
[fwupd] version: 1.1.5.190349
[fwupd] status details:""
[fw.sh] fwup_forced_update: 0
QoS auto-prioritize [info]: No networkID; skipping auto-priority update
|