ADT Pulse Gateway (PGZNG1)

bgn (N300)
ADT Pulse Gateway - Home Security Gateway with ZigBee
WikiDevi.wi-cat.ru	ADT Pulse Gateway (PGZNG1)
3rd Party Firmware
dd-wrt	Status Unknown
OpenWrt	Supported
Tomato any flavor	Incompatible
Gargoyle	Status Unknown
Platform
Brand • Model • Rev	ADT Pulse Gateway PGZNG1
FCC ID	PY312100192
IC ID	4054A-12100192
Type	home security gateway
CPU1 Y	Atheros AR9344
CPU1 Type	MIPS 74Kc
CPU1 Speed	560 MHz 32-bit
Flash1 Chip	SK hynix HY27UF082G2B-TPCB
Flash1 Size	256 MiB 268,435,456 B <br />2,097,152 Kib <br />262,144 KiB <br />2,048 Mib <br />0.25 GiB <br />
RAM1 Size	256 MiB 268,435,456 B <br />2,097,152 Kib <br />262,144 KiB <br />2,048 Mib <br />0.25 GiB <br />
RAM1 Chip	SK hynix H5DU5182ETR-E3C x 4
ETH chip1	Atheros AR9344
Switch	Atheros AR9344
Ethernet Port Count	1-100MbE-WAN 4-100MbE-LAN
Wired Standard	IEEE 802.3i/3u
802dot11 OUI: none specified
Stock bootloader	U-Boot
Expansion IF types	USB 2.0
USB ports	1
USB Hub Compatible	Untested
Power	12 VDC, 1.5 A
Connector type	barrel
Serial Port (UART)	yes
Flags: ZigBee, Z-Wave
Other
Manuf/OEM/ODM	Wistron NeWeb
3rd Party Firmware Support	OpenWrt • (List | Dev | DLs)
Retail
FCC approval date	05 July 2012
Country of manuf	China
Radio 1
Chip1	Atheros AR9344
Wireless interface OUI	none specified
Antenna Connector Type	U.FL
MIMO status	2x2:2
Wireless Standard	IEEE 802.11b/g/n
802.11n	up to 300 Mbps
802.11g	up to 54 Mbps
802.11b	up to 11 Mbps
WiFi Operating Frequency	2.4 GHz

For a list of all currently documented Atheros (QCA) chipsets with specifications, see Atheros.

• 300 Mbps - 2SS 2.4GHz 802.11n (40MHz chan.) = N300 class

Overview

"48.IN101.SGD" and "2012/03/16" is silkscreened on the board in the FCC photos.

The RAM chips appear to be H5DU5182ETR-E3C (64MB each, 256MB total).

The AR9344 P/N is AR9344-BC2A.

The FCC test report lists the following additional models as covered by this FCC ID..

• DSC C24-HUB2
• Netgear ASG1000 / (G2i)

See also Netgear ASG1100 (FCC ID: PY312300209)..

Flashing

Flashing OpenWrt

On the OpenWrt ToH (techdata entry)

Target: ath79
Subtarget: nand
Package architecture: mips_24kc
Supported Since Commit
Support started version: 23.05.0
Current supported version: 25.12.0

LAN Hardware: Atheros AR9344
WLAN Hardware: Atheros AR9344
WLAN Comment: ZigBee, Z-Wave
Installation method(s):
U-Boot TFTP + serial recovery, see git-commit

git • >>

ath79: add support for Netgear PGZNG1 This adds support for the Netgear PGZNG1, also known as the ADT Pulse Gateway. Hardware: CPU: Atheros AR9344 Memory: 256MB Storage: 256MB NAND SK hynix H27U2G8F2CTR-BC USB: 1x USB 2.0 Ethernet: 2x 100Mb/s WiFi: Atheros AR9340 2.4GHz 2T2R Leds: 8 LEDs Button: 1x Reset Button UART: Header marked JPE1. Pinout is VCC, TX, RX, GND. The marked pin, closest to the JPE1 marking, is VCC. Note VCC isn't required to be connected for UART to work. Enable Stock Firmware Shell Access: 1. Interrupt u-boot and run the following commands setenv console_mode 1 saveenv reset This will enable a UART shell in the firmware. You can then login using the root password of `icontrol`. If that doesn't work, the device is running a firmware based on OpenWRT where you can drop into failsafe to mount the FS and then modify /etc/passwd. Installation Instructions: 1. Interupt u-boot and run the following commands setenv active_image 0 setenv stock_bootcmd nboot 0x81000000 0 \${kernel_offset} setenv openwrt_bootcmd nboot 0x82000000 0 \${kernel_offset} setenv bootcmd run openwrt_bootcmd saveenv 2. boot initramfs image via TFTP u-boot tftpboot 0x82000000 openwrt-ath79-nand-netgear_pgzng1-initramfs-kernel.bin; bootm 0x82000000 3. Once booted, use LuCI sysupgrade to flash openwrt-ath79-nand-netgear_pgzng1-squashfs-sysupgrade.bin MAC Table: WAN (eth0): xx:xa - caldata 0x0 LAN (eth1): xx:xb - caldata 0x6 WLAN (phy0): xx:xc - burned into ath9k caldata Not Working: Z-Wave RS422