Amped Wireless ALLY-00X19

From TechInfoDepot
Jump to navigationJump to search
abgn+ac (AC1900)
ALLY Whole Home Smart Wi-Fi Range Extender
Homepage Product page
Support Support page
WikiDevi.wi-cat.ru Amped Wireless ALLY-00X19
3rd Party Firmware
dd-wrt Status Unknown
OpenWrt Supported
Tomato any flavor Incompatible
Gargoyle Status Unknown
Platform
Brand • Model • Rev Amped Wireless ALLY-00X19
FCC ID ZTT-ALLY00X19
Type range extender, mesh node
CPU1 checkY MediaTek MT7621AT
CPU1 Type MIPS 1004Kc
CPU1 Speed 880 MHz ( 2 cores ) 16-bit
Flash1 Chip Winbond W29N01GVSIAA
Flash1 Size 128 MiB 134,217,728 B <br />1,048,576 Kib <br />131,072 KiB <br />1,024 Mib <br />0.125 GiB <br />
RAM1 Size 128 MiB 134,217,728 B <br />1,048,576 Kib <br />131,072 KiB <br />1,024 Mib <br />0.125 GiB <br />
RAM1 Chip Nanya NT5CC64M16GP-DI
ETH chip1 MediaTek MT7621AT
Ethernet Port Count 1-1GbE-LAN
Wired Standard IEEE 802.3i/3u/3ab

802dot11 OUI: none specified

Stock bootloader U-Boot
Expansion IF types none specified
Power 12 VDC, 2 A
Connector type barrel
Serial Port (UART) yes, 3.3V TTL, (57600 8N1)

Flags:
Wave2, MU-MIMO

Additional chips
5GHz Power Amp Module;Skyworks;SKY85728-11;85728-11, 552LU, 1552, MY;3;

Other

Default SSID: Amped_ALLY_XXXX (4 addl. devices)
Default IP address: 192.168.3.1
the IP 192.168.3.1 is used by 32 additional devices
of which 17 are Amped Wireless devices

Manuf/OEM/ODM Edimax
3rd Party Firmware Support OpenWrt • (List | Dev | DLs)
Retail
FCC approval date 21 October 2016
ASIN B01LFRA3EO
Country of manuf China
Radio 1
Chip1 MediaTek MT7615N
Wireless interface OUI none specified
Antenna Connector Type U.FL
MIMO status 4x4:4
Wireless Standard IEEE 802.11b/g/n
802.11n up to 600 Mbps
802.11g up to 54 Mbps
802.11b up to 11 Mbps
WiFi Operating Frequency 2.4 GHz
Radio 2
Chip1 MediaTek MT7615N
Wireless interface OUI none specified
Antenna Connector Type U.FL
MIMO status 3x3:3
Wireless Standard IEEE 802.11a/n/ac
802.11ac up to 1300 Mbps
802.11n up to 450 Mbps
802.11a up to 54 Mbps
WiFi Operating Frequency 5 GHz
 FCC ID
Amped Wireless ALLY-00X21KZTT-ALLY00X19

For a list of all currently documented MediaTek chipsets with specifications, see MediaTek.

For a list of all currently documented Amped Wireless devices with specifications, see Amped Wireless.

• 600 Mbps - 3SS 2.4GHz 802.11n (40MHz chan., 256-QAM),
• 1300 Mbps - 3SS 5GHz 802.11ac (80MHz chan.) = AC1900 class

Overview

"1244-01001429-50Z ES" is silkscreened on the board in the FCC photos.

Presumably also known as ALLY-R1900K when sold as part of
the ALLY Plus Whole Home Smart Wi-Fi System (ALLY-0091K).

All Amped Wireless ALLY devices appear to be based on the same hardware with

some parts removed for the extenders and capabilities changed in software.
  • ALLY-00X19, ALLY-00X19K, ALLY-00X21K,
  • ALLY-R1900, ALLY-R1900K, ALLY-R2100K

Links of Interest

Reviews

Flashing

Flashing OpenWrt

Target: ramips
Subtarget: mt7621
Package architecture: mipsel_24kc
Supported Since Commit
Support started version: 21.02.0
Current supported version: 24.10.5
LAN Hardware: MediaTek MT7621AT
WLAN Hardware: 2x MediaTek MT7615N
WLAN Comment: MIMO 4x4 2.4Ghz, 3x3 5Ghz
Installation method(s):
U-Boot TFTP recovery, see git-commit
Recovery method(s):
U-Boot TFTP recovery, see git-commit
Comment:
Thru 21.02.3, initial installation requires manual patching of 1 file in order for sysupgrade to succeed; see: https://forum.openwrt.org/t/amped-ally-wireless-settings/119937
git • >> 
ramips: add support for Amped Wireless ALLY router and extender
Amped Wireless ALLY is a whole-home WiFi kit, with a router (model
ALLY-R1900K) and an Extender (model ALLY-00X19K).  Both are devices are
11ac and based on MediaTek MT7621AT and MT7615N chips.  The units are
nearly identical, except the Extender lacks a USB port and has a single
Ethernet port.

Specification:
- SoC: MediaTek MT7621AT (2C/4T) @ 880MHz
- RAM: 128MB DDR3 (Nanya NT5CC64M16GP-DI)
- FLASH: 128MB NAND (Winbond W29N01GVSIAA)
- WiFi: 2.4/5 GHz 4T4R
  - 2.4GHz MediaTek MT7615N bgn
  - 5GHz MediaTek MT7615N nac
- Switch: SoC integrated Gigabit Switch
- USB: 1x USB3 (Router only)
- BTN: Reset, WPS
- LED: single RGB
- UART:  through-hole on PCB.
   J1: pin1 (square pad, towards rear)=3.3V, pin2=RX,
   pin3=GND, pin4=TX.  Settings: 57600/8N1.

Note regarding dual system partitions
-------------------------------------

The vendor firmware and boot loader use a dual partition scheme.  The boot
partition is decided by the bootImage U-boot environment variable: 0 for
the 1st partition, 1 for the 2nd.

OpenWrt does not support this scheme and will always use the first OS
partition.  It will set bootImage to 0 during installation, making sure
the first partition is selected by the boot loader.

Also, because we can't be sure which partition is active to begin with, a
2-step flash process is used.  We first flash an initramfs image, then
follow with a regular sysupgrade.

Installation:

Router (ALLY-R1900K)
1) Install the flashable initramfs image via the OEM web-interface.
  (Alternatively, you can use the TFTP recovery method below.)
  You can use WiFi or Ethernet.
  The direct URL is:  http://192.168.3.1/07_06_00_firmware.html
  a. No login is needed, and you'll be in their setup wizard.
  b. You might get a warning about not being connected to the Internet.
  c. Towards the bottom of the page will be a section entitled "Or
  Manually Upgrade Firmware from a File:" where you can manually choose
  and upload a firmware file.
  d: Click "Choose File", select the OpenWRT "initramfs" image and click
  "Upload."
2) The Router will flash the OpenWrt initramfs image and reboot.  After
  booting, LuCI will be available on 192.168.1.1.
3) Log into LuCI as root; there is no password.
4) Optional (but recommended) is to backup the OEM firmware before
  continuing; see process below.
5) Complete the Installation by flashing a full OpenWRT image.  Note:
  you may use the sysupgrade command line tool in lieu of the UI if
  you prefer.
  a.  Choose System -> Backup/Flash Firmware.
  b.  Click "Flash Image..." under "Flash new firmware image"
  c.  Click "Browse..." and then select the sysupgrade file.
  d.  Click Upload to upload the sysupgrade file.
  e.  Important:  uncheck "Keep settings and retain the current
      configuration" for this initial installation.
  f.  Click "Continue" to flash the firmware.
  g.  The device will reboot and OpenWRT is installed.

Extender (ALLY-00X19K)
1) This device requires a TFTP recovery procedure to do an initial load
  of OpenWRT.  Start by configuring a computer as a TFTP client:
  a. Install a TFTP client (server not necessary)
  b. Configure an Ethernet interface to 192.168.1.x/24; don't use .1 or .6
  c. Connect the Ethernet to the sole Ethernet port on the X19K.
2) Put the ALLY Extender in TFTP recovery mode.
  a. Do this by pressing and holding the reset button on the bottom while
  connecting the power.
  b. As soon as the LED lights up green (roughly 2-3 seconds), release
  the button.
3) Start the TFTP transfer of the Initramfs image from your setup machine.
For example, from Linux:
tftp -v -m binary 192.168.1.6 69 -c put initramfs.bin
4) The Extender will flash the OpenWrt initramfs image and reboot.  After
booting, LuCI will be available on 192.168.1.1.
5) Log into LuCI as root; there is no password.
6) Optional (but recommended) is to backup the OEM firmware before
  continuing; see process below.
7) Complete the Installation by flashing a full OpenWRT image.  Note: you
may use the sysupgrade command line tool in lieu of the UI if you prefer.
  a.  Choose System -> Backup/Flash Firmware.
  b.  Click "Flash Image..." under "Flash new firmware image"
  c.  Click "Browse..." and then select the sysupgrade file.
  d.  Click Upload to upload the sysupgrade file.
  e.  Important:  uncheck "Keep settings and retain the current
      configuration" for this initial installation.
  f.  Click "Continue" to flash the firmware.
  g.  The device will reboot and OpenWRT is installed.

Backup the OEM Firmware:
-----------------------

There isn't any downloadable firmware for the ALLY devices on the Amped
Wireless web site. Reverting back to the OEM firmware is not possible
unless we have a backup of the original OEM firmware.

The OEM firmware may be stored on either /dev/mtd3 ("firmware") or
/dev/mtd6 ("oem").  We can't be sure which was overwritten with the
initramfs image, so backup both partitions to be safe.

  1) Once logged into LuCI, navigate to System -> Backup/Flash Firmware.
  2) Under "Save mtdblock contents," first select "firmware" and click
  "Save mtdblock" to download the image.
  3) Repeat the process, but select "oem" from the pull-down menu.

Revert to the OEM Firmware:
--------------------------
* U-boot TFTP:
  Follow the TFTP recovery steps for the Extender, and use the
  backup image.

* OpenWrt "Flash Firmware" interface:
  Upload the backup image and select "Force update"
  before continuing.

Signed-off-by: Jonathan Sturges

Pictures

Retail Images

See also

Retrieved from "https://techinfodepot.shoutwiki.com/w/index.php?title=Amped_Wireless_ALLY-00X19&oldid=538390"