COMFAST CF-E314N V2
From TechInfoDepot
Jump to navigationJump to search
| bgn (N300) | |
|---|---|
| 2.4G outdoor CPE bridge 300M long range Signal Booster extender | |
 | |
| 3rd Party Firmware | |
| dd-wrt | Status Unknown |
| OpenWrt | Supported |
| Tomato any flavor | Incompatible |
| Gargoyle | Status Unknown |
| Platform | |
| Brand • Model • Rev | COMFAST CF-E314N V2 |
| FCC ID | none specified |
| Type | access point, CPE |
CPU1  | Qualcomm Atheros QCA9531 |
| CPU1 Type | MIPS 24Kc |
| CPU1 Speed | 650 MHz |
| Flash1 Chip | Brand? Model? |
| Flash1 Size | 8 MiB 8,388,608 B <br />65,536 Kib <br />8,192 KiB <br />64 Mib <br />0.00781 GiB <br /> |
| RAM1 Size | 64 MiB 67,108,864 B <br />524,288 Kib <br />65,536 KiB <br />512 Mib <br />0.0625 GiB <br /> |
| RAM1 Chip | Brand? Model? |
| ETH chip1 | Qualcomm Atheros QCA9531 |
| Switch | Atheros AR8229 |
| Ethernet Port Count | 2-1GbE-LAN |
| Wired Standard | IEEE 802.3i/3u/3ab |
|
802dot11 OUI: none specified | |
| Stock bootloader | U-Boot |
| Expansion IF types | none specified |
| PoE | 802.3at, 802.3af, standard |
| Serial Port (UART) | yes |
|
| |
|
| |
| Other | |
|
| |
| 3rd Party Firmware Support |
OpenWrt • (List | Dev | DLs) |
| Radio 1 | |
| Chip1 | Qualcomm Atheros QCA9531 |
| Wireless interface OUI | none specified |
| Antenna Connector Type | none specified |
| MIMO status | 2x2:2 |
| Wireless Standard | IEEE 802.11b/g/n |
| 802.11n | up to 300 Mbps |
| 802.11g | up to 54 Mbps |
| 802.11b | up to 11 Mbps |
| WiFi Operating Frequency | 2.4 GHz |
For a list of all currently documented Atheros (QCA) chipsets with specifications, see Atheros.
For a list of all currently documented Qualcomm Atheros (QCA) chipsets with specifications, see Qualcomm Atheros.
For a list of all currently documented COMFAST devices with specifications, see COMFAST.
- • 300 Mbps - 2SS 2.4GHz 802.11n (40MHz chan.) = N300 class
Flashing
 | NOTE: During configuration or flashing a device, the only things that should be hooked to the device is the computer and power. |
Flashing OpenWrt
 | This device is NOT RECOMMENDED for future use with OpenWrt due to low flash/ram.
DO NOT BUY DEVICES WITH 8MB FLASH / 64MB RAM if you intend to flash an up-to-date and secure OpenWrt version onto it! See 8/64 warning for details. This device does not have sufficient resources (flash and/or RAM) to provide secure and reliable operation. This means that you will not be able to install many packages, and that you might experience crashes due to OOM situations more or less often. See OpenWrt on 8/64 devices what you can do now. |
Target: ath79
Subtarget: generic
Package architecture: mips_24kc
Supported Since Commit
Support started version: 21.02.0
Current supported version: 25.12.0
Subtarget: generic
Package architecture: mips_24kc
Supported Since Commit
Support started version: 21.02.0
Current supported version: 25.12.0
LAN Hardware: Atheros AR8229 rev 1
WLAN Hardware: Qualcomm Atheros QCA9531
Installation method(s):
U-Boot TFTP recovery, U-Boot web recovery, see git-commit
Recovery method(s):
U-Boot web recovery
WLAN Hardware: Qualcomm Atheros QCA9531
Installation method(s):
U-Boot TFTP recovery, U-Boot web recovery, see git-commit
Recovery method(s):
U-Boot web recovery
| git • >> |
|---|
ath79: add support for Comfast E314N-v2
Taken code from https://patchwork.ozlabs.org/patch/884850/ that was never
pushed by the author, and adapted to ath79.
The Comfast E314N-V2 is a 2.4 GHz 2x2 radio with a built-in directional
antenna and a second Ethernet port - very similar to the Ubiquiti
NanoStation M2. The Ethernet port features a pass-through PoE capability,
enabled or disabled with a slide switch.
Specifications :
- System-On-Chip: Qualcomm/Atheros QCA9531
- CPU/Speed: 650 MHz
- Flash size: 8 MiB
- RAM: 64 MiB
- 2 Ethernet 1Gbp
- 1 reset button
- 1 switch to choose PoE from LAN or Wan. 48Vdc
- Wifi 2.4 Ghz (b/g/n)
- UART inside the box (3.3V, pins marked on the PCB)
Firmware can be flashed on these units by the following method:
1.) Apply power to the unit
2.) Immediately AFTER applying power, hold down the reset button
3.) The WAN, LAN, and wireless lights will flash - wait three seconds
(three flashes) and then release the button.
4.) After a second, the lights will flutter quickly and the unit will be
visible at 192.168.1.1. A web page will be available to enable quick
and simple uploading and flashing of firmware.
During the boot process, these units also look for a tftp server at
192.168.1.10. If one is present, the firmware can be uploaded as a file
called firmware-auto.bin
|
Categories:
- COMFAST
- Embedded system/access point
- Embedded system/CPE
- Embedded System Qualcomm Atheros
- Embedded System QCA9531
- Qualcomm Atheros
- Embedded System MIPS 24Kc
- Embedded System
- Embedded System Atheros
- Embedded System AR8229
- Atheros
- OpenWrt Supported
- Has Mimo Status
- Embedded System IEEE 802.11b/g/n
- Single-Radio Wireless Embedded System
- Wireless Embedded System
- Single-Band
- English Documentation
