CREALITY BOX WB01

bgn (N150)
WiFi-enabled device
3rd Party Firmware
dd-wrt	Status Unknown
OpenWrt	Supported
Tomato any flavor	Incompatible
Gargoyle	Status Unknown
Platform
Brand • Model • Rev	CREALITY 3D BOX WB01
FCC ID	2AXH6CREALITY-BOX
Type	wireless router
CPU1 Y	MediaTek MT7688AN
CPU1 Type	MIPS 24KEc
CPU1 Speed	580 MHz
Flash1 Chip	BoyaMicro BY25Q128AS
Flash1 Size	16 MiB16,777,216 B <br />131,072 Kib <br />16,384 KiB <br />128 Mib <br />0.0156 GiB <br /> (SPI NOR)
RAM1 Size	128 MiB 134,217,728 B <br />1,048,576 Kib <br />131,072 KiB <br />1,024 Mib <br />0.125 GiB <br /> (DDR2)
RAM1 Chip	Winbond W971GG6SB-25
ETH chip1	MediaTek MT7688AN
Ethernet Port Count	1-100MbE-LAN
Wired Standard	IEEE 802.3i/3u
802dot11 OUI: none specified
Expansion IF types	microSDXC, USB 2.0
USB ports	2
SD/MMC Slots	1
USB Hub Compatible	Untested
Power	5 VDC, 2 A
Connector type	USB (Female Micro-B)
Serial Port (UART)	yes, 3.3V TTL, (57600 8N1)
Other
3rd Party Firmware Support	OpenWrt • (List | Dev | DLs)
Retail
Availability	End of Life
End of Life date	2022
Radio 1
Chip1	MediaTek MT7688AN
Wireless interface OUI	none specified
Antenna Connector Type	none specified
MIMO status	1x1:1
Wireless Standard	IEEE 802.11b/g/n
802.11n	up to 300 Mbps
802.11g	up to 54 Mbps
802.11b	up to 11 Mbps
WiFi Operating Frequency	2.4 GHz

For a list of all currently documented MediaTek chipsets with specifications, see MediaTek.

• 150 Mbps - 1SS 2.4GHz 802.11n (40MHz chan.) = N150 class

Flashing

Flashing OpenWrt

On the OpenWrt ToH (techdata entry)

Target: ramips
Subtarget: mt76x8
Package architecture: mipsel_24kc
Supported Since Commit
Support started version: 25.12.0
Current supported version: 25.12.2

WLAN Hardware: MediaTek MT7688AN
WLAN Comment: 1x1:1 MIMO
Installation method(s):
see git-commit
Recovery method(s):
see git-commit

git • >>

ramips: CREALITY BOX WB01 CREALITY BOX WB01 is small footprint router based on MediaTek MT7688, is a device intended to interface Creality brand 3D printers to a cloud service. Specifications: - SoC: MediaTek MT7688AN @ 580MHz - RAM: DDR2 128M (Winbond W971GG6SB-25) - Flash: BoyaMicro BY25Q128AS (16 MiB, SPI NOR) handled by BoHong bh25q128as driver - WiFi: 2.4GHz 1T1R internal panel antenna - Ethernet: 1x LAN (10/100) - USB: 2x USB2.0 port (Genesys Logic GL850G 2 port USB 2.0 hub) - UART: 3.3V, TX, RX, GND / 56700 8N1 / only pads on PCB - microSD SD-XC Class 10 slot - micro USB input (for power only) - reset button - FCC ID: 2AXH6CREALITY-BOX MAC addresses as verified by OEM firmware: vendor OpenWrt source LAN eth0 factory 0x2e 2.4GHz phy0-ap0 factory 0x04 (label) LEDs color vendor OpenWRT configurable red SD card activity - yes green Cloud connectivity status yes blue LAN activity eth0 yes yellow WIFI activity phy0tpt yes Return to OEM & debrick - download "cxsw_update.tar.bz2" from manufacturer site - extract archive to FAT32 USB stick root - put USB stick in USB2 port - press & hold reset button - power on device while holding reset - wait approx 10 sec - release reset button Installation with SD Card - power on device - wait for device to finish starting - copy "openwrt-ramips-mt76x8-creality_wb-01-squashfs-cxsw_update.tar.bz2" to root of FAT32 SD card - rename openwrt-ramips-mt76x8-creality_wb-01-squashfs-cxsw_update.tar.bz2 to "cxsw_update.tar.bz2" - put SD card in device - device will install OpenWRT on internal flash Installation via telnet: - extract the "factory.bin" and "install.sh" from newly created openwrt-ramips-mt76x8-creality_wb-01-squashfs-cxsw_update.tar.bz2 to FAT32 USB stick root - telnet to 10.10.10.254, user: root, password: cxswprin - plug the USB in USB1 port - cd /media/usbdisk/ - sh install.sh - device will write "factory.bin" to internal flash