Evaluation boards / unbranded boards XDX-RN502J
From TechInfoDepot
Jump to navigationJump to search
| bgn (N300) | |
|---|---|
| wireless router | |
|
| |
| 3rd Party Firmware | |
| dd-wrt | Incompatible |
| OpenWrt | Was Supported |
| Tomato any flavor | Incompatible |
| Gargoyle | Status Unknown |
| Platform | |
| Brand • Model • Rev | Evaluation boards / unbranded boards XDX-RN502J |
| FCC ID | none specified |
| Type | wireless router |
| CPU1 | Ralink RT3052 |
| CPU1 Type | MIPS 24KEc |
| CPU1 Speed | 384 MHz |
| Flash1 Chip | Brand? Model? |
| Flash1 Size | 4 MiB 4,194,304 B <br />32,768 Kib <br />4,096 KiB <br />32 Mib <br />0.00391 GiB <br /> |
| RAM1 Size | 32 MiB 33,554,432 B <br />262,144 Kib <br />32,768 KiB <br />256 Mib <br />0.0313 GiB <br /> |
| RAM1 Chip | Brand? Model? |
| ETH chip1 | Ralink RT3052 |
| Switch | Ralink RT3052 |
| Ethernet Port Count |
1-100MbE-WAN 4-100MbE-LAN |
| Wired Standard | IEEE 802.3i/3u |
|
802dot11 OUI: none specified | |
| Stock bootloader | U-Boot |
| Expansion IF types | USB 2.0 |
| USB ports | 1 |
| USB Hub Compatible | Untested |
|
| |
|
| |
| Other | |
|
| |
| 3rd Party Firmware Support |
OpenWrt (Was) |
| Radio 1 | |
| Chip1 | Ralink RT3052 |
| Wireless interface OUI | none specified |
| Antenna Connector Type | none specified |
| MIMO status | 2x2:2 |
| Wireless Standard | IEEE 802.11b/g/n |
| 802.11n | up to 300 Mbps |
| 802.11g | up to 54 Mbps |
| 802.11b | up to 11 Mbps |
| WiFi Operating Frequency | 2.4 GHz |
For a list of all currently documented Ralink chipsets with specifications, see Ralink.
- • 300 Mbps - 2SS 2.4GHz 802.11n (40MHz chan.) = N300 class
Flashing
| NOTE: During configuration or flashing a device, the only things that should be hooked to the device is the computer and power. |
Flashing OpenWrt
| This device is NO LONGER SUPPORTED OR POSSIBLE for future use with OpenWrt. |
Target: ramips
Subtarget: rt305x
Package architecture: mipsel_24kc
Supported Since Commit
Support started version: 12.09
Current supported version: EOL
Last Supported Version: 19.07.2
Image too big: 19.07.10
Subtarget: rt305x
Package architecture: mipsel_24kc
Supported Since Commit
Support started version: 12.09
Current supported version: EOL
Last Supported Version: 19.07.2
Image too big: 19.07.10
LAN Hardware: Ralink RT3052
WLAN Hardware: Atheros AR9285
Installation method(s):
U-Boot TFTP + serial recovery, see devicepage
Recovery method(s):
U-Boot TFTP + serial recovery
Comment:
Image build disabled in master with commit d7d46da938e3
WLAN Hardware: Atheros AR9285
Installation method(s):
U-Boot TFTP + serial recovery, see devicepage
Recovery method(s):
U-Boot TFTP + serial recovery
Comment:
Image build disabled in master with commit d7d46da938e3
| git • >> |
|---|
ramips: add support for unbranded XDX-RN502J board This patch adds support for routers using a PCB marked XDX-RN502J V2.0, such as some unbranded routers like this: http://www.mediafire.com/?8acv87h6snn9fj6 http://www.mediafire.com/?do7xonw7scor4kn http://www.mediafire.com/?1ad49zvx3e7jyix http://www.mediafire.com/?i46cqiq66maa197 http://www.aliexpress.com/product-fm/516397994-Free-Shipping-300M-3G-WAN-Wireless-N-WiFi-USB-AP-Router-2-Antennas-wholesalers.html some reports also state the Aceex 22Y uses the same board. more information can be found in the following openwrt forum post https://forum.openwrt.org/viewtopic.php?id=34878 [juhosg: fix checkpatch warnings, use the GENERIC_4M template] |
Categories:
- Evaluation boards / unbranded boards
- Embedded system/wireless router
- Embedded System Ralink
- Embedded System RT3052
- Ralink
- Embedded System MIPS 24KEc
- Embedded System
- OpenWrt Was Supported
- Has Mimo Status
- Embedded System IEEE 802.11b/g/n
- Single-Radio Wireless Embedded System
- Wireless Embedded System
- Single-Band
- English Documentation