Hiveton H5000M
From TechInfoDepot
Jump to navigationJump to search
| abgn+ac+ax+be | |
|---|---|
| WiFi Router | |
| 3rd Party Firmware | |
| dd-wrt | Status Unknown |
| OpenWrt | Supported |
| Tomato any flavor | Incompatible |
| Gargoyle | Status Unknown |
| Platform | |
| Brand • Model • Rev | Hiveton H5000M |
| FCC ID | none specified |
| Type | wireless router |
CPU1  | MediaTek MT7987A |
| CPU1 Type | ARM Cortex-A53 |
| CPU1 Speed | 2.0 GHz ( 4 cores ) 64-bit |
| Flash1 Chip | Brand? Model? |
| Flash1 Size | 8 GiB 8,192 MiB <br />8,589,934,592 B <br />67,108,864 Kib <br />8,388,608 KiB <br />65,536 Mib <br /> (eMMC) |
| RAM1 Size | 1 GiB 1,024 MiB <br />1,073,741,824 B <br />8,388,608 Kib <br />1,048,576 KiB <br />8,192 Mib <br /> (DDR4) |
| RAM1 Chip | Brand? Model? |
| ETH chip1 | MediaTek MT7987A |
| ETH chip2 | Realtek RTL8221B |
| Ethernet Port Count |
1-2.5GbE-WAN 1-2.5GbE-LAN |
| Wired Standard | IEEE 802.3i/3u/3ab/3bz |
| Port-based vlan | yes |
| 802.1q vlan | yes |
|
802dot11 OUI: none specified | |
| Stock bootloader | U-Boot |
| Expansion IF types | M.2 USB for 5G module |
| M.2 Slots | 1 |
| Power | ? VDC, ? A |
| Connector type | USB Type-C PD |
| Serial Port (UART) | yes, (115200 8N1) |
|
Flags: | |
|
| |
| Other | |
|
| |
| 3rd Party Firmware Support |
OpenWrt • (List | Dev | DLs) |
| Radio 1 | |
| Chip1 | MediaTek MT7987A |
| Chip2 | MediaTek MT7992 |
| Wireless interface OUI | none specified |
| Antenna Connector Type | none specified |
| MIMO status | 2x2:2 |
| Wireless Standard | IEEE 802.11b/g/n/ax/be |
| WiFi Operating Frequency | 2.4 GHz |
| Radio 2 | |
| Chip1 | MediaTek MT7987A |
| Chip2 | MediaTek MT7992 |
| Wireless interface OUI | none specified |
| Antenna Connector Type | none specified |
| MIMO status | 3x3:3 |
| Wireless Standard | IEEE 802.11a/n/ac/ax/be |
| WiFi Operating Frequency | 5 GHz |
| Radio 3 | |
| Chip1 | MediaTek MT7987A |
| Chip2 | MediaTek MT7992 |
| Wireless interface OUI | none specified |
| Antenna Connector Type | none specified |
| MIMO status | 3x3:3 |
| Wireless Standard | IEEE 802.11ax/be |
| WiFi Operating Frequency | 6 GHz |
For a list of all currently documented MediaTek chipsets with specifications, see MediaTek.
For a list of all currently documented Realtek chipsets with specifications, see Realtek.
Flashing
 | NOTE: During configuration or flashing a device, the only things that should be hooked to the device is the computer and power. |
Flashing OpenWrt
 | The development branch can contain experimental code that is under active development and should not be used for production environments. Snapshot images may support additional hardware; however, it is experimental, considered unstable, and sometimes won't compile. |
| Prebuilt snapshot images do not come with any web interface or GUI. You will need to be comfortable using a command line and remote shell to install one yourself → How to install LuCI |
Target: mediatek
Subtarget: filogic
Package architecture: aarch64_cortex-a53
Supported Since Commit
Support started version: unknown
Current supported version: snapshot
Subtarget: filogic
Package architecture: aarch64_cortex-a53
Supported Since Commit
Support started version: unknown
Current supported version: snapshot
LAN Hardware: SoC 2.5Gbe Phy, RTL8221B 2.5Gbe Phy
WLAN Hardware: MediaTek MT7992
WLAN Comment: MT7992 Tri-band (2.4G, 5G, 6G) 2T2R+3T3R+3T3R 802.11be Wi-Fi
Installation method(s):
see git-commit
Recovery method(s):
see git-commit
WLAN Hardware: MediaTek MT7992
WLAN Comment: MT7992 Tri-band (2.4G, 5G, 6G) 2T2R+3T3R+3T3R 802.11be Wi-Fi
Installation method(s):
see git-commit
Recovery method(s):
see git-commit
| git • >> |
|---|
mediatek: add support for Hiveton H5000M Hardware specification: SoC: MediaTek MT7987A Flash: 8GB eMMC RAM: 1GB DDR4 Ethernet: 2x 2.5GbE (RTL8221B PHY + Internal PHY) WiFi: MediaTek MT7992 / 2+3 antenna variant Interface: M.2 USB for 5G module LED: Power (hw-controlled), 2.5G WAN (user-definable), 5G Module (hw-controlled), LED-3 (user-definable), LED-4 (user-definable) Button: Reset, WPS Power: USB Type-C PD Other: PWM Fan control MAC address assignment is unconventional: the board has no Factory partition with pre-programmed MACs. Instead, all addresses are derived from the eMMC CID at runtime: LAN : macaddr_generate_from_mmc_cid mmcblk0 WAN : LAN + 1 (label_mac) phy0: LAN + 2 phy1: LAN + 3 This matches the vendor firmware behaviour and ensures stable, unique addresses across reboots without a dedicated EEPROM region for MACs. Flash instructions: Factory `mmcblk0p2` partition is empty, stock ImmortalWrt-798x-mt799x-6.6-mtwifi from PadavanOnly firmware uses `MT7991_MT7976_EEPROM_BE5040_iPAiLNA.bin`. Flashing this eeprom before flashing OpenWrt will make OpenWrt read eeprom: ``` dd if=/lib/firmware/MT7991_MT7976_EEPROM_BE5040_iPAiLNA.bin of=/dev/mmcblk0p2 bs=1 count=7680 sync ``` But it will have wifi issues for now. It's better to use OpenWrt fallback eeprom for now. Power off the device. Press and hold the Reset button. Power on the device while keeping the Reset button pressed. Wait for the device to enter U-Boot recovery mode. Connect to the device via Ethernet (default IP: 192.168.1.1). Set your PC's IP to 192.168.1.x (e.g., 192.168.1.100). Open a web browser and navigate to http://192.168.1.1 Upload and flash the OpenWrt firmware Wait for the flashing process to complete and the device to reboot. Signed-off-by: Fil Dunsky Link: https://github.com/openwrt/openwrt/pull/21398 Signed-off-by: Jonas Jelonek |
Categories:
- Hiveton
- Embedded system/wireless router
- Embedded System MediaTek
- Embedded System MT7987A
- MediaTek
- Embedded System ARM
- Embedded System Cortex-A53
- Embedded System RTL8221B
- Embedded System Realtek
- Realtek
- OpenWrt Supported
- Embedded System MT7992
- Has Mimo Status
- Embedded System IEEE 802.11b/g/n/ax/be
- Embedded System IEEE 802.11a/n/ac/ax/be
- Embedded System IEEE 802.11ax/be
- Triple-Radio Wireless Embedded System
- Wireless Embedded System
- Tri-Band
- Embedded System
- English Documentation
- New Entry
