Humax E10

abgn+ac (AC2600)
Wi-Fi System
3rd Party Firmware
dd-wrt	Status Unknown
OpenWrt	Supported
Tomato any flavor	Incompatible
Gargoyle	Status Unknown
Platform
Brand • Model • Rev	Humax E10
FCC ID	none specified
Type	wireless router
CPU1 Y	MediaTek MT7621A
CPU1 Type	MIPS 1004Kc
CPU1 Speed	880 MHz ( 2 cores ) 16-bit
Flash1 Chip	Brand? Model?
Flash1 Size	16 MiB 16,777,216 B <br />131,072 Kib <br />16,384 KiB <br />128 Mib <br />0.0156 GiB <br />
RAM1 Size	128 MiB 134,217,728 B <br />1,048,576 Kib <br />131,072 KiB <br />1,024 Mib <br />0.125 GiB <br />
RAM1 Chip	Brand? Model?
ETH chip1	MediaTek MT7621A
Switch	MediaTek MT7621A
Ethernet Port Count	2-1GbE-LAN
Wired Standard	IEEE 802.3i/3u/3ab
802dot11 OUI: none specified
Expansion IF types	USB 2.0
USB ports	1
USB Hub Compatible	Untested
Serial Port (UART)	yes, 3.3V TTL, (57600 8N1)
Other
3rd Party Firmware Support	OpenWrt • (List | Dev | DLs)
Radio 1
Chip1	MediaTek MT7615
Wireless interface OUI	none specified
Antenna Connector Type	none specified
MIMO status	4x4:4
Wireless Standard	IEEE 802.11b/g/n
n-QAM	up to 800 Mbps
802.11n	up to 600 Mbps
802.11g	up to 54 Mbps
802.11b	up to 11 Mbps
WiFi Operating Frequency	2.4 GHz
Radio 2
Chip1	MediaTek MT7615
Wireless interface OUI	none specified
Antenna Connector Type	none specified
MIMO status	4x4:4
Wireless Standard	IEEE 802.11a/n/ac
802.11ac	up to 1733 Mbps
802.11n	up to 600 Mbps
802.11a	up to 54 Mbps
WiFi Operating Frequency	5 GHz

For a list of all currently documented MediaTek chipsets with specifications, see MediaTek.

For a list of all currently documented Humax devices with specifications, see Humax.

• 800 Mbps - 4SS 2.4GHz 802.11n (40MHz chan., 256-QAM),

• 1733 Mbps - 4SS 5GHz 802.11ac (80MHz chan.) = AC2600 class

Flashing

Flashing OpenWrt

On the OpenWrt ToH (techdata entry)

Target: ramips
Subtarget: mt7621
Package architecture: mipsel_24kc
Supported Since Commit
Support started version: 22.03.0
Current supported version: 25.12.3

LAN Hardware: MediaTek MT7621A
WLAN Hardware: MediaTek MT7615
Installation method(s):
GUI OEM
Recovery method(s):
see git-commit

git • >>

ramips: add support for HUMAX E10 HUMAX E10 (also known as HUMAX QUANTUM E10) is a 2.4/5GHz band AC router, based on MediaTek MT7621A. Specifications: - SoC: MT7621A - RAM: DDR3 128MB - Flash: SPI NOR 16MB (MXIC MX25L12805D) - WiFi: - 2.4GHz: MT7615 - 5GHz: MT7615 - Ethernet: 2x 10/100/1000Mbps - Switch: SoC internal - USB: 1x USB 2.0 Type-A - UART: J1 (57600 8N1) - pinout: [3V3] (RXD) (GND) (TXD) Installation via web interface: - Flash **factory** image through the stock web interface. Recovery procedure: 1. Connect ethernet cable between Router **LAN** port and PC Ethernet port. 2. Set your computer to a static IP **192.168.1.1** 3. Turn the device off and wait a few seconds. Hold the WPS button on front of device and insert power. 4. Send a firmware image to **192.168.1.6** using TFTP. You can use any TFTP client. (tftp, curl, Tftpd64...) - It can accept both images which is HUMAX stock firmware dump (0x70000-0x1000000) image and OpenWRT **sysupgrade** image. Signed-off-by: Kyoungkyu Park [remove trailing whitespace] Signed-off-by: Sungbo Eo