Linksys E4200 v2
| abgn (AN900) | |||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| Maximum Performance Dual-Band N Router | |||||||||||||
|
| |||||||||||||
| Support | Support page | ||||||||||||
| Wikipedia | Linksys routers | ||||||||||||
| InfoDepot Wiki | Linksys E4200 v2.0 | ||||||||||||
| WikiDevi.wi-cat.ru | Linksys E4200 v2 | ||||||||||||
| 3rd Party Firmware | |||||||||||||
| dd-wrt | Not Supported | ||||||||||||
| OpenWrt | Partial Support | ||||||||||||
| Tomato any flavor | Incompatible | ||||||||||||
| Gargoyle | Not Supported | ||||||||||||
| Platform | |||||||||||||
| Brand • Model • Rev | Linksys E4200 v2 | ||||||||||||
| Serial number prefix | 01C106, 01C116, 01C136 | ||||||||||||
| FCC ID | Q87-E4200V2 | ||||||||||||
| IC ID | 3839A-E4200V2 | ||||||||||||
| Type | wireless router | ||||||||||||
| CPU1 | Marvell 88F6282 | ||||||||||||
| CPU1 Type | ARMv5 | ||||||||||||
| CPU1 Speed | 1.2 GHz 32-bit | ||||||||||||
| Flash1 Chip | SK hynix H5PS1G63EFR-S6C | ||||||||||||
| Flash1 Size | 128 MiB 134,217,728 B <br />1,048,576 Kib <br />131,072 KiB <br />1,024 Mib <br />0.125 GiB <br /> (NAND) | ||||||||||||
| RAM1 Size | 128 MiB 134,217,728 B <br />1,048,576 Kib <br />131,072 KiB <br />1,024 Mib <br />0.125 GiB <br /> | ||||||||||||
| RAM1 Chip | SK hynix H27U1G8F2BTR-BC | ||||||||||||
| ETH chip1 | Marvell 88F6282 | ||||||||||||
| Switch | Marvell 88E6171R | ||||||||||||
| Ethernet Port Count |
1-1GbE-WAN 4-1GbE-LAN | ||||||||||||
| Wired Standard | IEEE 802.3i/3u/3ab | ||||||||||||
| Stock bootloader | U-Boot | ||||||||||||
| Stock FW OS | Linux | ||||||||||||
| Expansion IF types | USB 2.0 | ||||||||||||
| USB ports | 1 | ||||||||||||
| USB Hub Compatible | Untested | ||||||||||||
| Power | 12 VDC, 2 A | ||||||||||||
| Connector type | barrel | ||||||||||||
| Serial Port (UART) | yes, 6-pin header, 3.3V TTL, (115200 8N1) | ||||||||||||
| JTAG Port | yes | ||||||||||||
|
| |||||||||||||
|
Additional chips | |||||||||||||
| Other | |||||||||||||
|
Default IP address: 192.168.1.1 | |||||||||||||
| Manuf/OEM/ODM | Wistron NeWeb RGWM04 .0GA | ||||||||||||
| 3rd Party Firmware Support |
OpenWrt • (List | Dev | DLs) , Debian , IP Fire | ||||||||||||
| Retail | |||||||||||||
| Availability | End of Life | ||||||||||||
| FCC approval date | 22 September 2011 | ||||||||||||
| UPC |
745883594900 (UPC DB, On eBay) | ||||||||||||
| ASIN |
B0068ALV8Q | ||||||||||||
| Country of manuf | China | ||||||||||||
| Radio 1 | |||||||||||||
| Chip1 | Marvell 88W8366 | ||||||||||||
| Chip2 | Marvell 88W8063 | ||||||||||||
| Wireless interface OUI | 58:6D:8F, C0:C1:C0 | ||||||||||||
| Antenna Connector Type | U.FL | ||||||||||||
| MIMO status | 3x3:3 | ||||||||||||
| Wireless Standard | IEEE 802.11b/g/n | ||||||||||||
| 802.11n | up to 450 Mbps | ||||||||||||
| 802.11g | up to 54 Mbps | ||||||||||||
| 802.11b | up to 11 Mbps | ||||||||||||
| WiFi Operating Frequency | 2.4 GHz | ||||||||||||
| Radio 2 | |||||||||||||
| Chip1 | Marvell 88W8366 | ||||||||||||
| Chip2 | Marvell 88W8063 | ||||||||||||
| Wireless interface OUI | 58:6D:8F, C0:C1:C0 | ||||||||||||
| Antenna Connector Type | U.FL | ||||||||||||
| MIMO status | 3x3:3 | ||||||||||||
| Wireless Standard | IEEE 802.11a/n | ||||||||||||
| 802.11n | up to 450 Mbps | ||||||||||||
| 802.11a | up to 54 Mbps | ||||||||||||
| WiFi Operating Frequency | 5 GHz | ||||||||||||
| |||||||||||||
| |||||||||||||
For a list of all currently documented Marvell chipsets with specifications, see Marvell.
For a list of all currently documented Linksys devices with specifications, see Linksys.
Overview
"48RGWM04.0GA" and "Manufactured for CISCO" are silkscreened on the board.
- Wistron NeWeb is the OEM.
The same hardware appears to be used with the later model Linksys EA4500.
Links of Interest
Reviews
- On SmallNetBuilder (source for this page)
Forum threads
Blogs
- Hacking Linksys E4200v2 firmware (binwalk dump)
Firmware
- (based on and extending work from the following)
- Installing Debian on the Linksys E4200v2
Flashing
| NOTE: During configuration or flashing a device, the only things that should be hooked to the device is the computer and power. |
Flashing OpenWrt
Subtarget: generic
Package architecture: arm_xscale
Supported Since Commit
Support started version: 15.05
Current supported version: 25.12.5
WPA3
LAN Hardware: Marvell 88E6171R
WLAN Hardware: 2x Marvell 88W8366
WLAN Comment: 3x3, no DFS support
Installation method(s):
GUI OEM, see devicepage
Recovery method(s):
See devicepage
Comment:
Same hardware as EA4500 v1; works with images for EA4500, see https://forum.openwrt.org/viewtopic.php?pid=289937
| git • >> |
|---|
kirkwood: add Linksys routers to default profile |
JTAG-Serial Info
Serial
Serial Pinouts
The serial port is marked as J5 on the board. There are 6 pads in a row.
If you take pin 1 to be the square pad, you will find the following pinout:
P1 - ? P2 - ? P3 - RX P4 - ? P5 - TX P6 - GND
Pictures
- Linksys
- Embedded system/wireless router
- Embedded System Marvell
- Embedded System 88F6282
- Marvell
- Embedded System ARMv5
- Embedded System
- Embedded System 88E6171R
- Manuf Wistron NeWeb
- OpenWrt Supported
- Embedded System 88W8366
- Embedded System 88W8063
- Has Mimo Status
- Embedded System IEEE 802.11b/g/n
- Embedded System IEEE 802.11a/n
- Dual-Radio Wireless Embedded System
- Wireless Embedded System
- Dual-Band
- English Documentation