Mercusys MB130-4G v1

abgn+ac (AC1200)
AC1200 Wireless Dual Band 4G LTE Router
Homepage	Product page
3rd Party Firmware
dd-wrt	Status Unknown
OpenWrt	Supported
Tomato any flavor	Incompatible
Gargoyle	Status Unknown
Platform
Brand • Model • Rev	Mercusys MB130-4G v1
FCC ID	none specified
Type	wireless router
CPU1 Y	MediaTek MT7628AN
CPU1 Type	MIPS 24KEc
CPU1 Speed	580 MHz
Flash1 Chip	Winbond W25Q128JV
Flash1 Size	16 MiB 16,777,216 B <br />131,072 Kib <br />16,384 KiB <br />128 Mib <br />0.0156 GiB <br />
RAM1 Size	128 MiB 134,217,728 B <br />1,048,576 Kib <br />131,072 KiB <br />1,024 Mib <br />0.125 GiB <br />
RAM1 Chip	Zentel A3R1GE40JBF-8E
ETH chip1	MediaTek MT7628AN
Switch	MediaTek MT7628AN
Ethernet Port Count	2-100MbE-LAN
Wired Standard	IEEE 802.3i/3u
802dot11 OUI: none specified
Stock bootloader	U-Boot
Expansion IF types	none specified
Connector type	barrel
Serial Port (UART)	yes, 3.3V TTL, (115200 8N1)
Flags: LTE
Other
3rd Party Firmware Support	OpenWrt • (List | Dev | DLs)
Radio 1
Chip1	MediaTek MT7628AN
Wireless interface OUI	none specified
Antenna Connector Type	none specified
MIMO status	2x2:2
Wireless Standard	IEEE 802.11b/g/n
802.11n	up to 300 Mbps
802.11g	up to 54 Mbps
802.11b	up to 11 Mbps
WiFi Operating Frequency	2.4 GHz
Radio 2
Chip1	MediaTek MT7663
Wireless interface OUI	none specified
Antenna Connector Type	none specified
MIMO status	2x2:2
Wireless Standard	IEEE 802.11a/n/ac
802.11ac	up to 867 Mbps
802.11n	up to 300 Mbps
802.11a	up to 54 Mbps
WiFi Operating Frequency	5 GHz

For a list of all currently documented MediaTek chipsets with specifications, see MediaTek.

For a list of all currently documented Mercusys devices with specifications, see Mercusys.

• 300 Mbps - 2SS 2.4GHz 802.11n (40MHz chan.),

• 867 Mbps - 2SS 5GHz 802.11ac (80MHz chan.) = AC1200 class

Flashing

Flashing OpenWrt

On the OpenWrt ToH (techdata entry)

Target: ramips
Subtarget: mt76x8
Package architecture: mipsel_24kc
Supported Since Commit
Support started version: 25.12.0
Current supported version: 25.12.2

LAN Hardware: MediaTek MT7628AN
LAN Comment: Quectel EC200A-EL 4G modem (USB)
WLAN Hardware: MediaTek MT7628AN, MediaTek MT7663
WLAN Comment: 2 SMA connectors for optional external LTE antennas
Installation method(s):
see git-commit
Recovery method(s):
see git-commit
Comment:
Quectel EC200A-EL 4G modem (USB)

git • >>

ramips: mt76x8: add support for MERCUSYS MB130-4G v1 Specification: SoC: MediaTek MT7628AN RAM: 128 MB, Zentel A3R1GE40JBF-8E Flash: 16MB, Winbond W25Q128JV Switch: rt3050-esw, 2 ports 100 Mbps WiFi: MediaTek mt7628-wmac 2.4GHz 802.11n and MediaTek MT7663 5GHz 802.11ac (PCIe) WWAN: Quectel EC200A-EL 4G modem (USB) GPIO: * 1 button (Reset/WPS) * 6 LEDs (Power+WPS, LAN, 3xSignal) * USB port power controls * Modem reset * Modem programming switch * Internal/external antenna switch for 4G Serial Interface: TP10 - 3.3V can be used for level shifter, if needed TP9 - TX TP8 - RX TP11 - GND Interface properties: 115200, 8N1 Access to console using serial port for OEM firmware: Username: admin Password: 1234 Flashing via TFTP (no disassembling or soldering required): 1. Connect your PC and router to port LAN 2. Configure PC interface using static IP 192.168.1.225, mask 255.255.255.0 3. Place OpenWRT firmware image (*-squashfs-tftp-recovery.bin) to TFTP root folder and renamed it to tp_recovery.bin 4. Unplug power from router 5. Press and hold Reset/WPS button 6. Power up the router 7. Wait until TFTP started uploading image (~10 seconds after power up) and release Reset/WPS button 8. Wait until image uploaded, i.e. until LAN LED start lighting 9. Enable DHCP address on PC interface and wait for assigning address 10. Use ssh (root@192.168.1.1) to configure router properties Depends on patch for firmware-utils package: https://github.com/openwrt/firmware-utils/commit/2051fe5b