Microchip SAM9X60-EK
From TechInfoDepot
Jump to navigationJump to search
| Single Board Computer | |
 | |
| 3rd Party Firmware | |
|---|---|
| dd-wrt | Status Unknown |
| OpenWrt | Supported |
| Tomato any flavor | Incompatible |
| Gargoyle | Status Unknown |
| Platform | |
| Brand • Model • Rev | Microchip SAM9X60-EK |
| Type | single-board computer |
CPU1  | Microchip SAM9X60 |
| CPU1 Speed | 600 MHz |
| Flash1 Chip | Micron MT29F4G08ABAEA |
| Flash1 Size | 512 MiB 536,870,912 B <br />4,194,304 Kib <br />524,288 KiB <br />4,096 Mib <br />0.5 GiB <br /> (NAND) |
| Flash2 Chip | Microchip SST26VF064B |
| Flash2 Size | 8 MiB8,388,608 B <br />65,536 Kib <br />8,192 KiB <br />64 Mib <br />0.00781 GiB <br /> (QSPI) |
| RAM1 Size | 512 MiB 536,870,912 B <br />4,194,304 Kib <br />524,288 KiB <br />4,096 Mib <br />0.5 GiB <br /> (DDR2) |
| RAM1 Chip | Winbond W972GG6KB-25 |
| ETH chip1 | Microchip SAM9X60 |
| Ethernet Port Count | 1-100MbE-LAN |
| Wired Standard | IEEE 802.3i/3u |
|
| |
| Expansion IF types | SD, one PIO connector, one mikrobus connector, USB 2.0 |
| USB ports | 3 |
| SD/MMC Slots | 1 |
| USB Hub Compatible | Untested |
| Power | 5 VDC, 1 A |
| Connector type | barrel |
| Serial Port (UART) | Yes |
| JTAG Port | Yes |
|
| |
|
| |
| Other | |
|
| |
| 3rd Party Firmware Support |
OpenWrt • (List | Dev | DLs) |
For a list of all currently documented Microchip (SMSC) chipsets with specifications, see Microchip.
For a list of all currently documented Microchip devices with specifications, see Microchip.
Flashing
 | NOTE: During configuration or flashing a device, the only things that should be hooked to the device is the computer and power. |
Flashing OpenWrt
Target: at91
Subtarget: sam9x
Package architecture: arm_arm926ej-s
Supported Since Commit
Support started version: 22.03.0
Current supported version: 25.12.0
Subtarget: sam9x
Package architecture: arm_arm926ej-s
Supported Since Commit
Support started version: 22.03.0
Current supported version: 25.12.0
WLAN Comment: Slot for optional Microchip ATWILC3000
Installation method(s):
SD card
Recovery method(s):
SD card
Comment:
MikroBus connector
Installation method(s):
SD card
Recovery method(s):
SD card
Comment:
MikroBus connector
| git • >> |
|---|
at91: add support for sam9x60-ek board
Add support for SAM9X60-EK board.
Hardware:
- SoC: SAM9X60
- RAM: Winbond W972GG6KB-25 (2Gbit DDR2)
- NAND Flash: Micron MT29F4G08ABAEA
- QSPI Flash: Microchip SST26VF064B
- EEPROM: Microchip 24AA02E48
- SDMMC: One standard 4-bit SD card interface
- USB: two stacked Type-A connectors with power switches, one micro-B
USB device
- CAN: 2 interfaces (Microchip MCP2542)
- Ethernet: one 10/100Mbps
- WiFi/BT: one optional WiFi/Bluetooth interface
- Audio: one ClassD port
- Display: one 24-bit LCD interface
- Camera: one 12-bit image sensor interface
- IO: one IO expander (Microchip MCP23008)
- Debug ports: one J-Link-OB + CDC, one JTAG interface
- Leds: one RGB LED
- Buttons: 4 push button switches
- Expansion: one PIO connector, one mikrobus connector
- Power management: two power regulators, two power consumption measurement
devices
Flashing:
- follow the procedure at [1]
[1] https://www.linux4sam.org/bin/view/Linux4SAM/Sam9x60EKMainPage#Create_a_SD_card_with_the_demo
|
