NEC Aterm WF1200HP
From TechInfoDepot
Jump to navigationJump to search
| abgn+ac (AC1200) | |||||||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| WiFi Router | |||||||||||||||||
| Homepage | Product page | ||||||||||||||||
| 3rd Party Firmware | |||||||||||||||||
| dd-wrt | Status Unknown | ||||||||||||||||
| OpenWrt | Supported | ||||||||||||||||
| Tomato any flavor | Incompatible | ||||||||||||||||
| Gargoyle | Status Unknown | ||||||||||||||||
| Platform | |||||||||||||||||
| Brand • Model • Rev | NEC Aterm WF1200HP | ||||||||||||||||
| FCC ID (fcc.io) | none specified | ||||||||||||||||
| FCC ID (fcc.report) | none specified | ||||||||||||||||
| Type | wireless router | ||||||||||||||||
| CPU1 | Atheros AR9344 | ||||||||||||||||
| CPU1 Type | MIPS 74Kc | ||||||||||||||||
| CPU1 Speed | 560 MHz 32-bit | ||||||||||||||||
| Flash1 Chip | Macronix MX25L6406EM2I-12G | ||||||||||||||||
| Flash1 Size | 8 MiB8,388,608 B <br />65,536 Kib <br />8,192 KiB <br />64 Mib <br />0.00781 GiB <br /> (SPI NOR) | ||||||||||||||||
| RAM1 Size | 128 MiB134,217,728 B <br />1,048,576 Kib <br />131,072 KiB <br />1,024 Mib <br />0.125 GiB <br /> (DDR2) | ||||||||||||||||
| RAM1 Chip | ESMT M14D5121632A-2.5BG2A | ||||||||||||||||
| ETH chip1 | Atheros AR9344 | ||||||||||||||||
| Switch | Atheros AR9344 | ||||||||||||||||
| Ethernet Port Count | 4-100MbE-LAN | ||||||||||||||||
| Wired Standard | IEEE 802.3i/3u | ||||||||||||||||
| Expansion IF types | none specified | ||||||||||||||||
| Power | 12 VDC, 0.7 A | ||||||||||||||||
| Serial Port (UART) | yes, 3.3V TTL, (9600 8N1) | ||||||||||||||||
|
| |||||||||||||||||
|
| |||||||||||||||||
| Other | |||||||||||||||||
|
| |||||||||||||||||
| 3rd Party Firmware Support |
OpenWrt • (List | Dev | DLs) | ||||||||||||||||
| Radio 1 | |||||||||||||||||
| Chip1 | Atheros AR9344 | ||||||||||||||||
| Wireless interface OUI | C0:25:A2 | ||||||||||||||||
| Antenna Connector Type | none specified | ||||||||||||||||
| MIMO status | 2x2:2 | ||||||||||||||||
| Wireless Standard | IEEE 802.11b/g/n | ||||||||||||||||
| 802.11n | up to 300 Mbps | ||||||||||||||||
| 802.11g | up to 54 Mbps | ||||||||||||||||
| 802.11b | up to 11 Mbps | ||||||||||||||||
| WiFi Operating Frequency | 2.4 GHz | ||||||||||||||||
| Radio 2 | |||||||||||||||||
| Chip1 | Qualcomm Atheros QCA9882 | ||||||||||||||||
| Wireless interface OUI | C0:25:A2 | ||||||||||||||||
| Antenna Connector Type | none specified | ||||||||||||||||
| MIMO status | 2x2:2 | ||||||||||||||||
| Wireless Standard | IEEE 802.11a/n/ac | ||||||||||||||||
| 802.11ac | up to 867 Mbps | ||||||||||||||||
| 802.11n | up to 300 Mbps | ||||||||||||||||
| 802.11a | up to 54 Mbps | ||||||||||||||||
| WiFi Operating Frequency | 5 GHz | ||||||||||||||||
| |||||||||||||||||
For a list of all currently documented Atheros (QCA) chipsets with specifications, see Atheros.
For a list of all currently documented Qualcomm Atheros (QCA) chipsets with specifications, see Qualcomm Atheros.
For a list of all currently documented NEC devices with specifications, see NEC.
Flashing
| NOTE: During configuration or flashing a device, the only things that should be hooked to the device is the computer and power. |
Flashing OpenWrt
| This device is NOT RECOMMENDED for future use with OpenWrt due to low flash/ram.
DO NOT BUY DEVICES WITH 8MB FLASH / 64MB RAM if you intend to flash an up-to-date and secure OpenWrt version onto it! See 8/64 warning for details. This device does not have sufficient resources (flash and/or RAM) to provide secure and reliable operation. This means that you will not be able to install many packages, and that you might experience crashes due to OOM situations more or less often. See OpenWrt on 8/64 devices what you can do now. |
Target: ath79
Subtarget: tiny
Package architecture: mips_24kc
Support started version: 25.12.0
Current supported version: 25.12.0
Subtarget: tiny
Package architecture: mips_24kc
Support started version: 25.12.0
Current supported version: 25.12.0
LAN Hardware: Atheros AR9344
WLAN Hardware: Atheros AR9344 / Qualcomm Atheros QCA9882
Installation method(s):
see git-commit
Recovery method(s):
see git-commit
WLAN Hardware: Atheros AR9344 / Qualcomm Atheros QCA9882
Installation method(s):
see git-commit
Recovery method(s):
see git-commit
| git • >> |
|---|
ath79: add support for NEC Aterm WF1200HP
NEC Aterm WF1200HP is a 2.4/5 GHz band 11ac (Wi-Fi 5) router with FE
ports, based on AR9344.
Specification:
- SoC : Atheros AR9344
- RAM : DDR2 128 MiB (2x ESMT M14D5121632A-2.5BG2A)
- Flash : SPI-NOR 8 MiB (Macronix MX25L6406EM2I-12G)
- WLAN : 2.4/5 GHz 2T2R
- 2.4 GHz : Atheros AR9344 (SoC)
- 5 GHz : Qualcomm Atheros QCA9882
- Ethernet : 4x 10/100 Mbps
- switch : Atheros AR9344 (SoC)
- LEDs/Keys (GPIO) : 12x/4x
- note : all LEDs are controlled by ath10k chip (QCA9882)
- UART : through-hole on PCB (J1)
- assignment : 3.3V, GND, NC, TX, RX from tri-angle marking
- settings : 9600n8 (U-Boot: 115200n8)
- Power : 12 VDC, 0.7 A (Max. 8 W)
- Stock OS : NetBSD based
Flash instruction using initramfs-factory.bin image (StockFW WebUI):
1. Boot WF1200HP with router mode
2. Access to the WebUI ("http://aterm.me/" or "http://192.168.10.1/") on
the device and open firmware update page ("ファームウェア更新")
3. Select the OpenWrt initramfs-factory.bin image and click update
("更新") button
4. After updating, the device will be rebooted and booted with OpenWrt
initramfs image
5. On the initramfs image, upload (or download) uboot.bin and
sysupgrade.bin image to the device
6. Replace the bootloader with uboot.bin image
mtd write <uboot.bin image> bootloader
7. Perform sysupgrade with sysupgrade.bin image
sysupgrade <sysuppgrade image>
8. Wait ~120 seconds to complete flashing and rebooting
Flash instruction using initramfs-factory.bin image (bootloader CLI):
1. Connect and open serial console
2. Power on WF1200HP and interrupt bootloader by ESC key
3. Login to the bootloader CLI with the password "chiron"
4. Start TFTP server by "tftpd" command
5. Upload initramfs-factory.bin via tftp from your computer
example (Windows): tftp -i 192.168.0.1 PUT initramfs-factory.bin
6. Boot initramfs image by "boot" command
7. On the initramfs image, backup the stock bootloader and firmware if
needed
8. Upload (or download) uboot.bin and sysupgrade.bin image to the
device
9. Replace the bootloader with uboot.bin image (see above)
10. Perform sysupgrade with sysupgrade.bin image (see above)
11. Wait ~120 seconds to complete flashing and rebooting
Notes:
- The stock bootloader requires the unknown filesystem on firmware area
in the flash chip. Booting OpenWrt from that filesystem cannot be
handled, so the bootloader needs to be replaced to mainline U-Boot
before OpenWrt installation.
Known issues:
- All LEDs on the front side are connected to the GPIO controller on the
ath10k chip (QCA9882) and controlled by it. The current ath10k driver
supports only one LED as "ath10k-phyN", but using as a GPIO controller
is not supported yet. As a result, all 12x LEDs on the front side
cannot be controlled by users.
MAC Addresses:
LAN : C0:25:A2:xx:xx:44 (config, 0x6 (hex))
WAN : C0:25:A2:xx:xx:45 (config, 0xc (hex))
2.4 GHz: C0:25:A2:xx:xx:46 (config, 0x0 (hex))
5 GHz : C0:25:A2:xx:xx:47 (config, 0x12 (hex))
|
Categories:
- NEC
- Embedded system/wireless router
- Embedded System Atheros
- Embedded System AR9344
- Atheros
- Embedded System MIPS 74Kc
- Embedded System
- OpenWrt Supported
- Has Mimo Status
- Embedded System IEEE 802.11b/g/n
- Embedded System Qualcomm Atheros
- Embedded System QCA9882
- Qualcomm Atheros
- Embedded System IEEE 802.11a/n/ac
- Dual-Radio Wireless Embedded System
- Wireless Embedded System
- Dual-Band
- English Documentation