NEC Aterm WG1200CR

From TechInfoDepot
Jump to navigationJump to search
abgn+ac (AC1200)
AC1200 Wireless Router
Homepage Product page
3rd Party Firmware
dd-wrt Status Unknown
OpenWrt Supported
Tomato any flavor Incompatible
Gargoyle Status Unknown
Platform
Brand • Model • Rev NEC Aterm WG1200CR
FCC ID none specified
Type wireless router
CPU1 checkY Qualcomm Atheros QCA9563
CPU1 Type MIPS 74Kc
CPU1 Speed 775 MHz
Flash1 Chip Brand? Model?
Flash1 Size 8 MiB 8,388,608 B <br />65,536 Kib <br />8,192 KiB <br />64 Mib <br />0.00781 GiB <br /> (SPI NOR)
RAM1 Size 128 MiB 134,217,728 B <br />1,048,576 Kib <br />131,072 KiB <br />1,024 Mib <br />0.125 GiB <br /> (DDR2)
RAM1 Chip Brand? Model?
ETH chip1 Qualcomm Atheros QCA9563
Switch Qualcomm Atheros QCA8334
Ethernet Port Count 2-1GbE-LAN
Wired Standard IEEE 802.3i/3u/3ab

802dot11 OUI: none specified

Stock bootloader U-Boot
Expansion IF types none specified
Power 12 VDC, 1 A
Serial Port (UART) yes, 3.3V TTL, (115200 8N1)
Other
3rd Party Firmware Support OpenWrt • (List | Dev | DLs)
Radio 1
Chip1 Qualcomm Atheros QCA9563
Wireless interface OUI none specified
Antenna Connector Type none specified
MIMO status 2x2:2
Wireless Standard IEEE 802.11b/g/n
802.11n up to 300 Mbps
802.11g up to 54 Mbps
802.11b up to 11 Mbps
WiFi Operating Frequency 2.4 GHz
Radio 2
Chip1 Qualcomm Atheros QCA9888
Wireless interface OUI none specified
Antenna Connector Type none specified
MIMO status 2x2:2
Wireless Standard IEEE 802.11a/n/ac
802.11ac up to 867 Mbps
802.11n up to 300 Mbps
802.11a up to 54 Mbps
WiFi Operating Frequency

5

OpenWrt GHz

For a list of all currently documented Qualcomm Atheros (QCA) chipsets with specifications, see Qualcomm Atheros.

For a list of all currently documented NEC devices with specifications, see NEC.

• 300 Mbps - 2SS 2.4GHz 802.11n (40MHz chan.),
• 867 Mbps - 2SS 5GHz 802.11ac (80MHz chan.) = AC1200 class

Flashing

Flashing OpenWrt

Target: ath79
Subtarget: generic
Package architecture: mips_24kc
Supported Since Commit
Support started version: 19.07.0
Current supported version: 25.12.2
LAN Hardware: Atheros QCA8334
WLAN Hardware: Qualcomm Atheros QCA9563, Qualcomm Atheros QCA9888
WLAN Comment: 2x2:2 MIMO both channels
Installation method(s):
GUI OEM, see git-commit
git • >>
ath79: add support for NEC Aterm WG1200CR
NEC Aterm WG1200CR is a 2.4/5 GHz band 11ac router,
based on Qualcomm Atheros QCA9563.

Specification:

- SoC		: Qualcomm Atheros QCA9563
- RAM		: DDR2 128 MiB
- Flash		: SPI-NOR 8 MiB
- WLAN		: 2.4/5 GHz 2T2R
  - 2.4 GHz	: QCA9563 (SoC)
  - 5 GHz	: QCA9888
- Ethernet	: 2x 10/100/1000 Mbps
  - Switch	: QCA8334
- LEDs/Input	: 12x/4x (2x buttons, 1x slide-switch)
- UART		: through-hole on PCB
  - JP1: Vcc, GND, NC, TX, RX from power connector side
  - 115200 bps

Flash instruction using factory image:

1. Boot WG1200CR normaly
2. Access to "http://192.168.10.1/" and open firmware update page
("ファームウェア更新")
3. Select the OpenWrt factory image and click update ("更新") button
to perform firmware update
4. Wait ~150 seconds to complete flashing

Known issues:

- cannot be controlled LEDs other than Power (Green/Red)
  - only Power LEDs are connected to SoC GPIO; other LEDs
    connected to the gpiochip on ath10k chip (QCA9888)