NanoPi R3S

Single Board Computer
Homepage	Product page
3rd Party Firmware
dd-wrt	Status Unknown
OpenWrt	Supported
Tomato any flavor	Incompatible
Gargoyle	Status Unknown
Platform
Brand • Model • Rev	FriendlyELEC NanoPi R3S
Type	single-board computer
CPU1 N	Rockchip RK3566
CPU1 Type	ARM Cortex-A55
CPU1 Speed	1.8 GHz ( 4 cores ) 64-bit
Flash1 Chip	Brand? Model?
Flash1 Size	? MiB (eMMC)
RAM1 Size	2 GiB 2,048 MiB <br />2,147,483,648 B <br />16,777,216 Kib <br />2,097,152 KiB <br />16,384 Mib <br /> (LPDDR4X)
RAM1 Chip	Brand? Model?
ETH chip1	Rockchip RK3566
ETH chip2	Realtek RTL8211F
ETH chip3	Realtek RTL8111H
Ethernet Port Count	1-1GbE-WAN 1-1GbE-LAN
Wired Standard	IEEE 802.3i/3u/3ab
Stock bootloader	U-Boot
Expansion IF types	microSD, USB 3.0
USB ports	1
SD/MMC Slots	1
USB Hub Compatible	Untested
Power	5 VDC, 3 A
Connector type	USB-C
Serial Port (UART)	yes, 3.3V TTL
Other
3rd Party Firmware Support	OpenWrt • (List | Dev | DLs)

For a list of all currently documented Realtek chipsets with specifications, see Realtek.
For a list of all currently documented Rockchip SoC's with specifications, see Rockchip.

For a list of all currently documented FriendlyELEC devices with specifications, see FriendlyELEC.

Flashing

Flashing OpenWrt

On the OpenWrt ToH (techdata entry)
On the OpenWrt Wiki
On the OpenWrt Forum

Target: rockchip
Subtarget: armv8
Package architecture: aarch64_generic
Supported Since Commit
Support started version: 24.10.0
Current supported version: 25.12.5

LAN Comment: RTL8211F native 1G x1, RTL8111H pcie 1G x1
WLAN Hardware: none
WLAN Comment: No WLAN
Installation method(s):
SD card, see git-commit
Recovery method(s):
SD card, Serial

git • >>

rockchip: Add support for RK3566 FriendlyElec NanoPi R3S This commit adds support for the FriendlyElec NanoPi R3S. CPU: Rockchip RK3566, Quad-core Cortex-A55 RAM: 2GB LPDDR4X Ethernet: GMAC RTL8211F GbE, PCIe R8111H GbE USB3.0 Host: Type-A x1 Storage: MicroSD Slot x 1, and optional on-board 32GB eMMC Debug Serial Port: 3.3V TTL, 3-pin 2.54mm pitch connector, 1500000 bauds LED: LED x 3 RTC: One low-power RTC, supports backup battery input Both GbE controllers are working (WAN eth0, LAN eth1). Appropriate LAN/WAN interface assignments and MAC address generation. All three LEDs are working. USB appears to be working and has been tested with mass storage. Installation - microSD: -Uncompress the OpenWRT sysupgrade.img.gz -Write image to microSD card using dd or similar tool Installation - eMMC: -Boot from microSD -Uncompress the OpenWRT sysupgrade.img.gz -Flash to eMMC : dd if=x.img of=/dev/mmcblk0 -sync -Remove microSD card -Reboot