Netgear Orbi Pro (SXS80)

From TechInfoDepot
Jump to navigationJump to search
abgn+ac+ax (AX60003R)
Orbi Pro AX6000 WiFi 6 Tri-band Add-on Satellite
Support Support page
Wikipedia Netgear
3rd Party Firmware
dd-wrt Status Unknown
OpenWrt Supported
Tomato any flavor Incompatible
Gargoyle Status Unknown
Platform
Brand • Model • Rev Netgear SXS80
FCC ID PY320100484
Type wireless router
Series Orbi
CPU1 checkY Qualcomm IPQ8074A
CPU1 Type ARM Cortex-A53
CPU1 Speed 2.2 GHz ( 4 cores ) 64-bit
Flash1 Chip Winbond W29N04GZ
Flash1 Size 512 MiB 536,870,912 B <br />4,194,304 Kib <br />524,288 KiB <br />4,096 Mib <br />0.5 GiB <br /> (SPI NAND)
RAM1 Size 1 GiB 1,024 MiB <br />1,073,741,824 B <br />8,388,608 Kib <br />1,048,576 KiB <br />8,192 Mib <br />
RAM1 Chip Brand? Model?
ETH chip1 Qualcomm IPQ8074A
Switch Qualcomm Atheros QCA8075
Ethernet Port Count 1-2.5GbE-WAN
4-1GbE-LAN
Wired Standard IEEE 802.3i/3u/3ab/3bz

802dot11 OUI: none specified

Stock bootloader U-Boot
Expansion IF types none specified
Power 12 VDC, 3.5 A
Connector type barrel

Flags:
Wi-Fi 6

Other
3rd Party Firmware Support OpenWrt • (List | Dev | DLs)
Radio 1
Chip1 Qualcomm QCN5024
Wireless interface OUI none specified
Antenna Connector Type none specified
MIMO status 4x4:4
Wireless Standard IEEE 802.11b/g/n/ax
802.11ax up to 1148 Mbps
802.11n up to 600 Mbps
802.11g up to 54 Mbps
802.11b up to 11 Mbps
WiFi Operating Frequency 2.4 GHz
Radio 2
Chip1 Qualcomm QCN5054
Wireless interface OUI none specified
Antenna Connector Type none specified
MIMO status 4x4:4
Wireless Standard IEEE 802.11a/n/ac/ax
802.11ax up to 2402 Mbps
802.11ac up to 1733 Mbps
802.11n up to 600 Mbps
802.11a up to 54 Mbps
WiFi Operating Frequency 5 GHz
Radio 3
Chip1 Qualcomm QCN5054
Wireless interface OUI none specified
Antenna Connector Type none specified
MIMO status 4x4:4
Wireless Standard IEEE 802.11a/n/ac/ax
802.11ax up to 2402 Mbps
802.11ac up to 1733 Mbps
802.11n up to 600 Mbps
802.11a up to 54 Mbps
WiFi Operating Frequency 5 GHz
 FCC ID
Netgear Orbi Pro (SXR80)PY320100484

For a list of all currently documented Qualcomm chipsets with specifications, see Qualcomm.
For a list of all currently documented Qualcomm Atheros (QCA) chipsets with specifications, see Qualcomm Atheros.

For a list of all currently documented Netgear devices with specifications, see Netgear.

• 2x 2402 Mbps - 4SS 5GHz 802.11ax (80MHz chan., 1024-QAM)
• 1x 1148 Mbps - 4SS 2.4GHz 802.11ax (40MHz chan., 256-QAM) = AX6000 class

Flashing

Flashing OpenWrt

Target: qualcommax
Subtarget: ipq807x
Package architecture: aarch64_cortex-a53
Supported Since Commit
Support started version: 24.10.0
Current supported version: 24.10.5
LAN Hardware: Qualcomm Atheros QCA8075
LAN Comment: Qualcomm QCA8081 2.5Gbe Phy
WLAN Hardware: Qualcomm QCN5024, 2x Qualcomm QCN5054
WLAN Comment: 2.4 GHz 4x4:4 MIMO, 2x 5 GHz 4x4:4 MIMO
(second radio high channels only)
Installation method(s):
see git-commit
Recovery method(s):
see git-commit
git • >> 
qualcommax: ipq807x support Netgear Orbi Pro SXK80
This commit adds support for Netgear Orbi Pro SXR80 and SXS80 (collectively known as SXK80)

Specifications:
---------------
* CPU: Qualcomm IPQ8074A Quad core Cortex-A53
* RAM: 1024MB
* Storage: SPI-NAND 512 MiB (Winbond W29N04GZ)
* Ethernet: 4x 1G RJ45 ports (QCA8075) 1x 2.5G RJ45 LAN/WAN (QCA8081)
* WLAN:
    - 2.4 GHz: Qualcomm QCN5024 4x4
    - 2x 5 GHz: Qualcomm QCN5054 4x4 (second radio high channels only)
* LEDs:
    - Power: (Green and red)
    - Front: (Blue, green, red and white)
* Buttons:
    - 1x Soft reset
    - 1x Sync/WPS
* Power: 12V DC Jack

Installation instructions (Telnet):
-----------------------------------

*Note, this guide assumes SXR80, for SXS80 change the firmware file name as appropriate

1. Put firmware file openwrt-qualcommax-ipq807x-netgear_sxr80-initramfs-uImage.itb in root of TFTP server available at 192.168.1.10.
2. Enable telnet by going to http://[ip of device]/debug.htm and clicking on the tickbox 'Enable telnet'
3. Telnet into the device and login using the same username and password as the web interface:
4. Run the following command:

`fw_setenv bootcmd 'env default -a; saveenv; reset'`

5. Reboot the router, once the web interface is available again re-enable telnet via http://[ip of device]/debug.htm and telnet into the device.

6. Run the following command:

`fw_printenv`

It should look similar to the below:

```
baudrate=115200
bootargs=console=ttyMSM0,115200n8
bootcmd=mii write 0x0 0x0 0x800; sleep 1; nmrp; bootdni; boot_DNI_secureboot
bootdelay=2
ipaddr=192.168.1.1
netmask=255.255.255.0
serverip=192.168.1.10
soc_version_major=2
soc_version_minor=0
```

**If you see the message:**
`Warning: Bad CRC, using default environment`
**DO NOT CONTINUE, YOU WILL BRICK YOUR DEVICE**

7. Run the following command:

`fw_setenv originalboot 'mii write 0x0 0x0 0x800; sleep 1; nmrp; bootdni; boot_DNI_secureboot'`

(This should match what's in the bootcmd variable displayed in step 6)

8. Run the following commands:
```
fw_setenv wrttftp 'mii write 0x0 0x0 0x800; sleep 1; nmrp; if tftpboot openwrt-qualcommax-ipq807x-netgear_sxr80-initramfs-uImage.itb; then bootm; fi; bootdni; boot_DNI_secureboot'
fw_setenv wrtboot 'mii write 0x0 0x0 0x800; sleep 1; nmrp; nand read 0x40000000 0x1980000 0x06d00000; bootm 0x40000000'
fw_setenv bootcmd 'run wrttftp'
```

9. Ensure SXR/S device is attached via ethernet (LAN port) to the same ethernet segment as the TFTP server.

10. Reboot the device, it should reboot into OpenWrt and be available on 192.168.1.1

11. Once OpenWrt has booted, update the bootcmd using the following command:

`fw_setenv bootcmd 'run wrtboot'`

12. Flash the sysupgrade image

13. It should boot into OpenWrt

References to SXK80 GPL source:
https://www.downloads.netgear.com/files/GPL/SXK80-V3.2.0.108_gpl_src.tar.bz2.zip
Retrieved from "https://techinfodepot.shoutwiki.com/w/index.php?title=Netgear_Orbi_Pro_(SXS80)&oldid=519757"