Netgear WN3100RP v2
From TechInfoDepot
Jump to navigationJump to search
| bgn (N300) | |
|---|---|
| N300 WiFi Range Extender | |
 | |
| Wikipedia | Netgear |
| 3rd Party Firmware | |
| dd-wrt | Status Unknown |
| OpenWrt | Supported |
| Tomato any flavor | Incompatible |
| Gargoyle | Status Unknown |
| Platform | |
| Brand • Model • Rev | Netgear WN3100RP v2 |
| FCC ID | none specified |
| Type | range extender |
CPU1  | MediaTek MT7620A |
| CPU1 Type | MIPS 24KEc |
| CPU1 Speed | 580 MHz 32-bit |
| Flash1 Chip | Brand? Model? |
| Flash1 Size | 8 MiB 8,388,608 B <br />65,536 Kib <br />8,192 KiB <br />64 Mib <br />0.00781 GiB <br /> |
| RAM1 Size | 32 MiB 33,554,432 B <br />262,144 Kib <br />32,768 KiB <br />256 Mib <br />0.0313 GiB <br /> |
| RAM1 Chip | Brand? Model? |
| ETH chip1 | MediaTek MT7620A |
| Ethernet Port Count | 1-100MbE-LAN |
| Wired Standard | IEEE 802.3i/3u |
|
802dot11 OUI: none specified | |
| Stock bootloader | U-Boot |
| Expansion IF types | none specified |
|
| |
|
| |
| Other | |
|
| |
| 3rd Party Firmware Support |
OpenWrt • (List | Dev | DLs) |
| Radio 1 | |
| Chip1 | MediaTek MT7620A |
| Wireless interface OUI | none specified |
| Antenna Connector Type | none specified |
| MIMO status | 2x2:2 |
| Wireless Standard | IEEE 802.11b/g/n |
| 802.11n | up to 300 Mbps |
| 802.11g | up to 54 Mbps |
| 802.11b | up to 11 Mbps |
| WiFi Operating Frequency | 2.4 GHz |
For a list of all currently documented MediaTek chipsets with specifications, see MediaTek.
For a list of all currently documented Netgear devices with specifications, see Netgear.
- • 300 Mbps - 2SS 2.4GHz 802.11n (40MHz chan.) = N300 class
Flashing
 | NOTE: During configuration or flashing a device, the only things that should be hooked to the device is the computer and power. |
Flashing OpenWrt
 | This device is NOT RECOMMENDED for future use with OpenWrt due to low flash/ram. DO NOT BUY DEVICES WITH 4MB FLASH / 32MB RAM if you intend to flash an up-to-date and secure OpenWrt version onto it! See 4/32 warning for details. |
| This device does not have sufficient resources (flash and/or RAM) to provide secure and reliable operation. This means that even setting a password or changing simple network settings might not be possible any more, rendering the device effectively useless. See OpenWrt on 4/32 devices what you can do now. |
| OpenWrt support for this device has ended in 2022. 19.07.10 was the last official build for 4/32 devices. |
Target: ramips
Subtarget: mt7620
Package architecture: mipsel_24kc
Supported Since Commit
Support started version: 22.03.0
Current supported version: 24.10.5
Subtarget: mt7620
Package architecture: mipsel_24kc
Supported Since Commit
Support started version: 22.03.0
Current supported version: 24.10.5
WLAN Hardware: MediaTek MT7620A
Installation method(s):
GUI OEM, U-Boot TFTP recovery, see git-commit
Recovery method(s):
U-Boot TFTP recovery, see git-commit
Installation method(s):
GUI OEM, U-Boot TFTP recovery, see git-commit
Recovery method(s):
U-Boot TFTP recovery, see git-commit
| git • >> |
|---|
ramips: add support for Netgear WN3100RPv2 This patch adds support for the Netgear WN3100RPv2 http://www.netgear.com/support/product/wn3100rpv2.aspx Specifications: - SoC: MediaTek MT7620A (580MHz, ramips) - RAM: 32MB DDR - Storage: 8MB NOR SPI flash - Wireless: builtin MT7620A, 2x2:2 with u.FL connectors - Ethernet: 1x100M - Stock firmware based on OpenWRT Kamikaze Like the EX2700, the bootloader expects a secondary image signature, see https://forum.openwrt.org/viewtopic.php?pid=312577#p312577 This device seems to be same hardware as a WN3000RPv3 Flash instructions: - Use the Netgear WebUI to upgrade to OpenWRT using the factory image (see note below), - Use the sysupgrade image for upgrading versions from OpenWRT, - TFTP recovery procedure can be used to flash the factory image (preferred method). Note: - The WebUI may not reboot automatically, wait at least 5 minutes before powercycling the device Flashing using TFTP: - Set you IP address to 192.168.1.10/24 (no gateway) - Connect your machine to the Ethernet port - Power off the device and wait for 10 seconds, - Hold the reset button and power on the device (do not release reset), - Hold the reset button until the green light is flashing (Approx. 15s) - launch tftp, set mode to binary and connect to 192.168.1.1 - put the factory firmware image - All leds will switch off (like a power off), this is normal - Wait for the device to reboot in the new OpenWRT image (max 5 mins) - The first boot will take longer than usual. - After boot, the Device IP on the ethernet port is 192.168.1.1 Signed-off-by: Rodolphe de Saint Léger <rdesaintleger@gmail.com> [drop unneeded includes in dts, wrap commit message] Signed-off-by: Sungbo Eo |
