OrayBox X1

From TechInfoDepot
Jump to navigationJump to search
bgn (N300)
Berry dandelion X1
Homepage Product page
3rd Party Firmware
dd-wrt Status Unknown
OpenWrt Supported
Tomato any flavor Incompatible
Gargoyle Status Unknown
Platform
Brand • Model • Rev OrayBox X1
FCC ID none specified
Type access point
CPU1 checkY MediaTek MT7628N
CPU1 Type MIPS 24KEc
CPU1 Speed 580 MHz 32-bit
Flash1 Chip Brand? XM25Q128
Flash1 Size 16 MiB 16,777,216 B <br />131,072 Kib <br />16,384 KiB <br />128 Mib <br />0.0156 GiB <br /> (NOR)
RAM1 Size 64 MiB 67,108,864 B <br />524,288 Kib <br />65,536 KiB <br />512 Mib <br />0.0625 GiB <br /> (DDR3)
RAM1 Chip Brand? Model?
ETH chip1 MediaTek MT7628N
Ethernet Port Count 1-100MbE-LAN
Wired Standard IEEE 802.3i/3u

802dot11 OUI: none specified

Stock bootloader U-Boot
Expansion IF types USB 2.0
USB ports 1
USB Hub Compatible Untested
Power 5 VDC, 1 A
Connector type microUSB
Other
3rd Party Firmware Support OpenWrt • (List | Dev | DLs)
Radio 1
Chip1 MediaTek MT7628N
Wireless interface OUI none specified
Antenna Connector Type none specified
MIMO status 2x2:2
Wireless Standard IEEE 802.11b/g/n
802.11n up to 300 Mbps
802.11g up to 54 Mbps
802.11b up to 11 Mbps
WiFi Operating Frequency 2.4 GHz

For a list of all currently documented MediaTek chipsets with specifications, see MediaTek.

For a list of all currently documented OrayBox devices with specifications, see OrayBox.

• 300 Mbps - 2SS 2.4GHz 802.11n (40MHz chan.) = N300 class

Flashing

Flashing OpenWrt

Target: ramips
Subtarget: mt76x8
Package architecture: mipsel_24kc
Supported Since Commit
Support started version: 23.05.0
Current supported version: 25.12.2
LAN Hardware: MediaTek MT7628N
WLAN Hardware: MediaTek MT7628N
WLAN Comment: MIMO 2x2:2
Installation method(s):
see git-commit
Recovery method(s):
see git-commit
git • >> 
ramips: add support for OrayBox X3A
OrayBox X3A is a 2.4/5GHz dual band AC router, based on MediaTek MT7621.

Specification:
* SoC: MT7621
* RAM: DDR3 128 MiB
* Flash: 16 MiB NOR (XM25Q128)
* Wi-Fi: (single chip hosting both 2.4G and 5G)
  * 2.4GHz: MT7615
  * 5GHz: MT7615
* Ethernet: 3x 1000Mbps
  * Switch: MT7530
* LED:
  * Ethernet LEDs: On the back of the router, hardware-controlled.
  * Status LEDs: One "pixel-like" RGB LED in the front of the router,
                 which is actually made up of 3 individual LEDs (with
                 dedicated GPIO pins) with the color of Red, Green,
                 and Blue.
                 The OEM firmware only lights up one color at a time to
                 indicate status, but that's very boring, and the colors
                 actually look great when combined, so I've improvised a
                 little and made them indicate netdev activities.
                 My test results:
                 GPIO 13/14/15
                 000 white (actually more like bright green or cyan
                            because the brightness of the green LED is
                            higher than red and blue)
                 001 bright purple
                 010 bright green
                 011 red
                 100 bright cyan
                 101 blue
                 110 green
                 111 off

Flash Layout:
 0x0000000-0x0030000 : "u-boot"
 0x0030000-0x0040000 : "u-boot-env"
 0x0040000-0x0050000 : "factory"
 0x0050000-0x0f50000 : "firmware"
 /*0x0f50000 to 0x0fe0000 is undefined, same as OEM firmware*/
 0x0fe0000-0x0ff0000 : "bdinfo"
 0x0ff0000-0x1000000 : "reserve"

MAC address:
 MAC               Source                          Description    Fix
 A0:CX:XX:BX:XX:0D BDINFO_9                        LAN(LABEL)     DTS
 A0:CX:XX:BX:XX:0E BDINFO_9 + 1                    WAN            DTS
 A2:CX:XX:BX:XX:0F FACTORY_4                       WIFI2G         DTS
 A2:CX:XX:CX:XX:0F SETBIT 7 (FACTORY_4 + 0x100000) WIFI5G         HOTPLUG
 A6:CX:XX:BX:XX:0F N/A                             WIFI2G_CLIENT  N/A
 A6:DX:XX:BX:XX:0F N/A                             WIFI5G_CLIENT  N/A

Stock dmesg:
https://pastebin.com/2t2jwLdf

Stock Dumps:
https://pastebin.com/LDLxSWX3

Installation via SSH (does not void your warranty):
1.  -----UNLOCK SSH-----
1.1 Set computer IP to DHCP mode, load 'http://10.168.1.1/cgi-bin/luci' in
    your browser. Password is 'admin'.
1.2 Click the "备份且导出" (backup and export) button, and download the
    config file.
1.3 Open the downloaded file with 7zip, navigate to '/etc/config/'.
1.4 Edit the file './system'. Change the '0' into '1' under
    "config sys 'ssh'".
1.5 Save the file.
1.6 Upload the file by clicking the "导入且恢复" (import and recover)
    button. The router will automatically reboot.
2.  -----FLASH THE OPENWRT FIRMWARE-----
2.1 Use any scp tool to upload the 'sysupgrade' firmware to the '/tmp/'
    folder to your router. It should be root@10.168.1.1 and the password
    is 'admin'.
2.2 SSH into the router, also root@10.168.1.1 and the password is 'admin'.
2.3 **IMPORTANT** Type command 'dd if=/dev/mtd3 of=/tmp/firmware.bin', to
    backup the stock firmware. Since the OEM does not provide firmware
    download on their website, this is the only way to get it.
2.3 **ALSO IMPORTANT** Use any scp tool to download your backed-up stock
    firmware from '/tmp/' to your local drive. Then you'd better use a hex
    reading tool to have a rough look at it to make sure nothing is
    corrupt. Or u can just back up again and cross check the MD5.
2.4 Type command 'mtd write /tmp/XXX.bin firmware', and it should flash
    the firmware.
2.5 Verify that nothing went wrong. If you're confident, type 'reboot' and
    reboot the router.

Revert to stock firmware:
1.  load stock firmware using mtd (make sure u have a backup).
Retrieved from "https://techinfodepot.shoutwiki.com/w/index.php?title=OrayBox_X1&oldid=517988"