Plasma Cloud PA2200

abgn+ac (AC21003R)
PA2200 Access Point
Homepage	Product page
3rd Party Firmware
dd-wrt	Status Unknown
OpenWrt	Supported
Tomato any flavor	Incompatible
Gargoyle	Status Unknown
Platform
Brand • Model • Rev	Plasma Cloud PA2200
FCC ID	none specified
Type	access point
CPU1 Y	Qualcomm IPQ4019
CPU1 Type	ARMv7 Cortex-A7
CPU1 Speed	716 MHz ( 4 cores )
Flash1 Chip	Winbond W25Q256
Flash1 Size	32 MiB 33,554,432 B <br />262,144 Kib <br />32,768 KiB <br />256 Mib <br />0.0313 GiB <br /> (SPI NOR)
RAM1 Size	256 MiB 268,435,456 B <br />2,097,152 Kib <br />262,144 KiB <br />2,048 Mib <br />0.25 GiB <br />
RAM1 Chip	Brand? Model?
ETH chip1	Qualcomm IPQ4019
ETH chip2	Qualcomm Atheros QCA8072
Ethernet Port Count	1-1GbE-WAN 1-1GbE-LAN
Wired Standard	IEEE 802.3i/3u/3ab
802dot11 OUI: none specified
Stock bootloader	U-Boot
Expansion IF types	none specified
PoE	802.3at, standard
Power	12 VDC, 2 A
Connector type	barrel
Flags: Wave 2
Other
3rd Party Firmware Support	OpenWrt • (List | Dev | DLs)
Radio 1
Chip1	Qualcomm IPQ4019
Wireless interface OUI	none specified
Antenna Connector Type	none specified
MIMO status	2x2:2
Wireless Standard	IEEE 802.11b/g/n
802.11n	up to 300 Mbps
802.11g	up to 54 Mbps
802.11b	up to 11 Mbps
WiFi Operating Frequency	2.4 GHz
Radio 2
Chip1	Qualcomm IPQ4019
Wireless interface OUI	none specified
Antenna Connector Type	none specified
MIMO status	2x2:2
Wireless Standard	IEEE 802.11a/n/ac
802.11ac	up to 867 Mbps
802.11n	up to 300 Mbps
802.11a	up to 54 Mbps
WiFi Operating Frequency	5 GHz
Radio 3
Chip1	Qualcomm Atheros QCA9888
Wireless interface OUI	none specified
Antenna Connector Type	none specified
MIMO status	2x2:2
Wireless Standard	IEEE 802.11a/n/ac
802.11ac	up to 867 Mbps
802.11n	up to 300 Mbps
802.11a	up to 54 Mbps
WiFi Operating Frequency	5 GHz

For a list of all currently documented Qualcomm chipsets with specifications, see Qualcomm.
For a list of all currently documented Qualcomm Atheros (QCA) chipsets with specifications, see Qualcomm Atheros.

• 1x 300 Mbps - 2SS 2.4GHz 802.11n (40MHz chan.),

• 2x 867 Mbps - 2SS 5GHz 802.11ac (80MHz chan.) = AC2100 class

Flashing

Flashing OpenWrt

On the OpenWrt ToH (techdata entry)

Target: ipq40xx
Subtarget: generic
Package architecture: arm_cortex-a7_neon-vfpv4
Supported Since Commit
Support started version: 21.02.0
Current supported version: 25.12.6

LAN Hardware: Qualcomm Atheros QCA8072
WLAN Hardware: Qualcomm Atheros IPQ4019, Qualcomm Atheros QCA9888
Installation method(s):
see git-commit

git • >>

ipq40xx: add support for Plasma Cloud PA2200 Device specifications: * QCA IPQ4019 * 256 MB of RAM * 32 MB of SPI NOR flash (w25q256) - 2x 15 MB available; but one of the 15 MB regions is the recovery image * 2T2R 2.4 GHz - QCA4019 hw1.0 (SoC) - requires special BDF in QCA4019/hw1.0/board-2.bin with bus=ahb,bmi-chip-id=0,bmi-board-id=20,variant=PlasmaCloud-PA2200 * 2T2R 5 GHz (channel 36-64) - QCA9888 hw2.0 (PCI) - requires special BDF in QCA9888/hw2.0/board-2.bin bus=pci,bmi-chip-id=0,bmi-board-id=16,variant=PlasmaCloud-PA2200 * 2T2R 5 GHz (channel 100-165) - QCA4019 hw1.0 (SoC) - requires special BDF in QCA4019/hw1.0/board-2.bin with bus=ahb,bmi-chip-id=0,bmi-board-id=21,variant=PlasmaCloud-PA2200 * GPIO-LEDs for 2.4GHz, 5GHz-SoC and 5GHz-PCIE * GPIO-LEDs for power (orange) and status (blue) * 1x GPIO-button (reset) * TTL pins are on board (arrow points to VCC, then follows: GND, TX, RX) * 2x gigabit ethernet - phy@mdio3: + Label: Ethernet 1 + gmac0 (ethaddr) in original firmware + used as LAN interface - phy@mdio4: + Label: Ethernet 2 + gmac1 (eth1addr) in original firmware + 802.3at POE+ + used as WAN interface * 12V 2A DC Flashing instructions: The tool ap51-flash (https://github.com/ap51-flash/ap51-flash) should be used to transfer the factory image to the u-boot when the device boots up.