ROSINSON WR818

bgn (N450)
Wireless Router
3rd Party Firmware
dd-wrt	Status Unknown
OpenWrt	Supported
Tomato any flavor	Incompatible
Gargoyle	Status Unknown
Platform
Brand • Model • Rev	ROSINSON WR818
FCC ID	none specified
Type	wireless router
CPU1 Y	Qualcomm Atheros QCA9563
CPU1 Type	MIPS 74Kc
CPU1 Speed	750 MHz
Flash1 Chip	Brand? Model?
Flash1 Size	16 MiB 16,777,216 B <br />131,072 Kib <br />16,384 KiB <br />128 Mib <br />0.0156 GiB <br />
RAM1 Size	128 MiB 134,217,728 B <br />1,048,576 Kib <br />131,072 KiB <br />1,024 Mib <br />0.125 GiB <br />
RAM1 Chip	Brand? Model?
ETH chip1	Qualcomm Atheros QCA9563
Switch	Qualcomm Atheros QCA8337N
Ethernet Port Count	1-1GbE-WAN 3-1GbE-LAN
Wired Standard	IEEE 802.3i/3u/3ab
802dot11 OUI: none specified
Stock bootloader	U-Boot
Expansion IF types	USB 2.0
USB ports	2
USB Hub Compatible	Untested
Power	12 VDC, 2 A
Connector type	barrel
Serial Port (UART)	yes
Other
3rd Party Firmware Support	OpenWrt • (List | Dev | DLs)
Radio 1
Chip1	Qualcomm Atheros QCA9563
Wireless interface OUI	none specified
Antenna Connector Type	none specified
MIMO status	3x3:3
Wireless Standard	IEEE 802.11b/g/n
802.11n	up to 450 Mbps
802.11g	up to 54 Mbps
802.11b	up to 11 Mbps
WiFi Operating Frequency	2.4 GHz

For a list of all currently documented Qualcomm Atheros (QCA) chipsets with specifications, see Qualcomm Atheros.

• 450 Mbps - 3SS 2.4GHz 802.11n (40MHz chan.) = N450 class

Flashing

Flashing OpenWrt

On the OpenWrt ToH (techdata entry)

Target: ath79
Subtarget: generic
Package architecture: mips_24kc
Supported Since Commit
Support started version: 19.07.0
Current supported version: 25.12.1

LAN Hardware: Qualcomm Atheros QCA8337N
WLAN Hardware: Qualcomm Atheros QCA9563
WLAN Comment: 3x3:3 MIMO
Installation method(s):
U-Boot web recovery, see git-commit

git • >>

ath79: add support for ROSINSON WR818 board This commit adds support for the ROSINSON WR818 WiFi-Router SoC: Qualcomm Atheros QCA9563, FLASH: Winbond W25Q128FV 16MBytes, WiFi: QCA9563 b/g/n 3x3 450Mbit/s, USB: 1x USB 2.0 Type A, 1x USB2.0 Type C, IN: WPS/Reset button GPIO1, OUT: Power LED red, Internet LED red, WLAN LED red, LAN1 LED red, LAN2 LED red, System LED red, UART: RX-GPIO18, TX-GPIO22, Tested and working: - Ethernet (LAN + WAN) - WiFi - OpenWRT sysupgrade - Button - LEDs Installation of OpenWRT from vendor firmware: - Connect to the Web-interface at http://192.168.1.1 - Go to "Administration" -> "Firmware Upgrade" - Upload the OpenWrt sysupgrade image