Rostelecom S1010

abgn+ac (AC1200)
AC1200 Wireless Router
3rd Party Firmware
dd-wrt	Status Unknown
OpenWrt	Supported
Tomato any flavor	Incompatible
Gargoyle	Status Unknown
Platform
Brand • Model • Rev	Rostelecom S1010
FCC ID	none specified
Type	wireless router
CPU1 Y	MediaTek MT7620A
CPU1 Type	MIPS 24KEc
CPU1 Speed	580 MHz 32-bit
Flash1 Chip	Brand? Model?
Flash1 Size	16 MiB 16,777,216 B <br />131,072 Kib <br />16,384 KiB <br />128 Mib <br />0.0156 GiB <br /> (SPI NOR)
RAM1 Size	64 MiB 67,108,864 B <br />524,288 Kib <br />65,536 KiB <br />512 Mib <br />0.0625 GiB <br />
RAM1 Chip	Brand? Model?
ETH chip1	MediaTek MT7620A
Switch	MediaTek MT7620A
Ethernet Port Count	1-100MbE-WAN 5-100MbE-LAN
Wired Standard	IEEE 802.3i/3u
802dot11 OUI: none specified
Stock bootloader	U-Boot
Expansion IF types	none specified
Power	12 VDC, 1 A
Connector type	barrel
Serial Port (UART)	yes, 3.3V TTL, (57600 8N1)
Other
3rd Party Firmware Support	OpenWrt • (List | Dev | DLs)
Radio 1
Chip1	MediaTek MT7620A
Wireless interface OUI	none specified
Antenna Connector Type	none specified
MIMO status	2x2:2
Wireless Standard	IEEE 802.11b/g/n
802.11n	up to 300 Mbps
802.11g	up to 54 Mbps
802.11b	up to 11 Mbps
WiFi Operating Frequency	2.4 GHz
Radio 2
Chip1	MediaTek MT7612EN
Wireless interface OUI	none specified
Antenna Connector Type	none specified
MIMO status	2x2:2
Wireless Standard	IEEE 802.11a/n/ac
802.11ac	up to 867 Mbps
802.11n	up to 300 Mbps
802.11a	up to 54 Mbps
WiFi Operating Frequency	5 GHz

For a list of all currently documented MediaTek chipsets with specifications, see MediaTek.

• 300 Mbps - 2SS 2.4GHz 802.11n (40MHz chan.),

• 867 Mbps - 2SS 5GHz 802.11ac (80MHz chan.) = AC1200 class

Flashing

Flashing OpenWrt

On the OpenWrt ToH (techdata entry)
On the OpenWrt Wiki

Target: ramips
Subtarget: mt7620
Package architecture: mipsel_24kc
Supported Since Commit
Support started version: 23.05.2
Current supported version: 25.12.2

LAN Hardware: MediaTek MT7620A
WLAN Hardware: MediaTek MT7620A, MediaTek MT7612EN
WLAN Comment: MIMO 2x2
Installation method(s):
see devicepage
Install Comment:
OEM web interface
Recovery method(s):
see devicepage
Recovery Comment:
sercomm-recovery

git • >>

ramips: add support for Sercomm CPJ routers This commit adds support for following wireless routers: - Rostelecom RT-FL-1 (Serсomm RT-FL-1) - Rostelecom S1010 (Serсomm S1010.RT) The devices are almost identical and the only difference is one bit in the factory image PID (thanks to Maximilian Weinmann <x1@disroot.org> (@MaxS0niX) for the info and idea to make one PR for two devices at once). Devices specification --------------------- SoC: MediaTek MT7620A, MIPS RAM: 64 MB Flash: 16 MB SPI NOR Wireless 2.4: MT7620 (b/g/n, 2x2) Wireless 5: MT7612EN (a/n/ac, 2x2) Ethernet: 5xFE (WAN, LAN1-4) BootLoader: U-Boot Buttons: 2 (wps, reset) LEDs: 1 amber and 1 green status GPIO leds 5 green ethernet GPIO leds 1 green GPIO 2.4 GHz WLAN led 1 green PHY 5 GHz WLAN led 1 green unmanaged power led USB ports: No Power: 12 VDC, 1 A Connector: Barrel OEM easy installation --------------------- 1. Remove all dots from the factory image filename (except the dot before file extension) 2. Upload and update the firmware via the original web interface 3. Wait until green status led stops blinking (can take several minutes) 4. Login to OpenWrt initramsfs. It's recommended to make a backup of the mtd partitions at this point. 4. Perform sysupgrade using the following command (or use Luci): sysupgrade -n sysupgrade.bin 5. Wait until green status les stops blinking (can take several minutes) 6. Mission acomplished Return to Stock --------------- Option 1. Restore firmware Slot1 from a backup (firmware2.bin): cd /tmp mtd -e Firmware2 write firmware2.bin Firmware2 printf 1 | dd bs=1 seek=$((0x18007)) count=1 of=/dev/mtdblock2 reboot Option 2. Decrypt, ungzip and split stock firmware image into the parts, take Slot1 parts (kernel2.bin, rootfs2.bin) and write them: cd /tmp mtd -e Kernel2 write kernel2.bin Kernel2 mtd -e RootFS2 write rootfs2.bin RootFS2 printf 1 | dd bs=1 seek=$((0x18007)) count=1 of=/dev/mtdblock2 reboot More about stock firmware decryption: Link: https://github.com/Psychotropos/sercomm_fwutils/ Debricking ---------- Use sercomm-recovery tool. You can use "ALL" mtd partition backup as a recovery image. Link: https://github.com/danitool/sercomm-recovery MAC addresses ------------- +---------+-------------------+-----------+ | | MAC | Algorithm | +---------+-------------------+-----------+ | label | 48:3e:xx:xx:xx:1e | label | | LAN | 48:3e:xx:xx:xx:1e | label | | WAN | 48:3e:xx:xx:xx:28 | label+10 | | WLAN 2g | 48:3e:xx:xx:xx:20 | label+2 | | WLAN 5g | 48:3e:xx:xx:xx:24 | label+6 | +---------+-------------------+-----------+ Co-authored-by: Vadzim Vabishchevich <bestmc2009@gmail.com> Signed-off-by: Mikhail Zhilkin