Sitecom WL-341 v2
bgn (N300) | |||||||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
wireless router | |||||||||||||||||
InfoDepot Wiki | |||||||||||||||||
3rd Party Firmware | |||||||||||||||||
dd-wrt | |||||||||||||||||
OpenWrt |
Incompatible | ||||||||||||||||
Tomato any flavor |
Incompatible | ||||||||||||||||
Gargoyle |
Status Unknown | ||||||||||||||||
Platform | |||||||||||||||||
Brand • Model • Rev |
Sitecom WL-341 v2 | ||||||||||||||||
FCC ID | |||||||||||||||||
Type |
wireless router | ||||||||||||||||
CPU1 |
Ralink RT3050 | ||||||||||||||||
CPU1 Type |
MIPS 24KEc | ||||||||||||||||
CPU1 Speed |
320 MHz 16-bit | ||||||||||||||||
Flash1 Chip |
Brand? Model? | ||||||||||||||||
Flash1 Size |
4 MiB4,194,304 B <br />32,768 Kib <br />4,096 KiB <br />32 Mib <br />0.00391 GiB <br /> | ||||||||||||||||
RAM1 Size |
16 MiB16,777,216 B <br />131,072 Kib <br />16,384 KiB <br />128 Mib <br />0.0156 GiB <br /> | ||||||||||||||||
RAM1 Chip |
Brand? Model? | ||||||||||||||||
ETH chip1 |
Ralink RT3050 | ||||||||||||||||
Switch |
Ralink RT3050 | ||||||||||||||||
Ethernet Port Count |
1-WAN 4-LAN | ||||||||||||||||
802dot11 OUI: none specified | |||||||||||||||||
Expansion IF types |
none specified | ||||||||||||||||
Power |
12 VDC, 1 A | ||||||||||||||||
Serial Port (UART) |
yes | ||||||||||||||||
Special Features |
ESR9753 ODM | ||||||||||||||||
Other | |||||||||||||||||
| |||||||||||||||||
3rd Party Firmware Support | |||||||||||||||||
Radio 1 | |||||||||||||||||
Chip1 |
Ralink RT3050 | ||||||||||||||||
Wireless interface OUI |
none specified | ||||||||||||||||
Antenna Connector Type |
none specified | ||||||||||||||||
MIMO status |
2x2:2 | ||||||||||||||||
Wireless Standard |
IEEE 802.11b/g/n | ||||||||||||||||
802.11n |
up to 300 Mbps | ||||||||||||||||
802.11g |
up to 54 Mbps | ||||||||||||||||
802.11b |
up to 11 Mbps | ||||||||||||||||
WiFi Operating Frequency |
2.4 GHz | ||||||||||||||||
| |||||||||||||||||
|
For a list of all currently documented Ralink chipsets with specifications, see Ralink.
For a list of all currently documented Sitecom device with specifications, see Sitecom.
- • 300 Mbps - 2SS 2.4GHz 802.11n (40MHz chan.) = N300 class
Overview
RT3050 clock speed is 320, overclocled?
Links of Interest
Flashing
NOTE: During configuration or flashing a device, the only things that should be hooked to the device is the computer and power. |
Flashing dd-wrt
Supported by dd-wrt as of = ESR9752 v.24 sp2 - build 12527 ?
THIS GUIDE IS ONLY FOR SITECOM WL-341 V2 .002
First of all toggle all screws behind the box.
There are five screws, one hidden behind on the center of the box.
Check for finding it.
Pay attention then toggle the upside of the box with care!
If you want to work well, you must to toggle the board and the antennas.
Personally, i have substituted that -so called- antennas with and external
"true" antenna.
Now chech for 6 soldered pins standing in the bottom left corner,
the first pins is square. On the left of the pins you can read "pwr,gnd,tx,rx"
The square pin is the power,the second is ground,the third is tx and the last is rx.
Don't care the rest of the pins, you need only these!
Now sold with a 25w iron solder 4 cables (i used utp cables) and plug the cables in the right order in the port of your ttl converter (yes, you must to have it,i payed it 5 euro)
Now get a static ip on your pc (192.168.1.57)
Plug utp cable and serial cable to the router and power on.
Now download "putty" and check for a serial use 57600bps 8bit NO FLOW CONTROL (toggle on settings of putty)
get the right number of port COM (COM1,COM2,COM8,COM12....)
Now reboot your router and if is all ok you'll see putty's window animate.
YOu must to check the button "2" at the start of the router for flash to NVRAM from tftp
Now download TFTPD32 and place it in the folder of the firmware dd-wrt.
start tftpd32
now click Y on putty for going on on flashing.
Now write 192.168.1.54 (for assign an ip to the router) and press enter
Now write 192.168.1.57 (your pc) and press enter
enter the name of the firmware checking the case-sensitive words (EnSenao.bin is better to rename before as ensenao.bin)
and press enter
now if oll is right, the router will download the firmware and the flashing will begin
Wait 5 minuter and then use a browser for the address 192.168.1.1
Reverting
Reverting from dd-wrt
The only known method for reverting is flashing original firmware downloaded as for dd-wrt firmware using the same steps.