UniElec U7621-01
From TechInfoDepot
Jump to navigationJump to search
| abgn+ac (AC1200) | |
|---|---|
| AX1800 Dual Band Gigabit Wi-Fi 6 Router | |
|
| |
| Homepage | Product page |
| 3rd Party Firmware | |
| dd-wrt | Status Unknown |
| OpenWrt | Supported |
| Tomato any flavor | Incompatible |
| Gargoyle | Status Unknown |
| Platform | |
| Brand • Model • Rev | UniElec U7621-01 |
| FCC ID | none specified |
| Type | wireless router |
| CPU1 | MediaTek MT7621AT |
| CPU1 Type | MIPS 1004Kc |
| CPU1 Speed | 880 MHz ( 2 cores ) 16-bit |
| Flash1 Chip | Brand? Model? |
| Flash1 Size | 16 MiB 16,777,216 B <br />131,072 Kib <br />16,384 KiB <br />128 Mib <br />0.0156 GiB <br /> |
| RAM1 Size | 256 MiB 268,435,456 B <br />2,097,152 Kib <br />262,144 KiB <br />2,048 Mib <br />0.25 GiB <br /> |
| RAM1 Chip | Brand? Model? |
| ETH chip1 | MediaTek MT7621AT |
| Switch | MediaTek MT7621AT |
| Ethernet Port Count |
1-1GbE-WAN 4-1GbE-LAN |
| Wired Standard | IEEE 802.3i/3u/3ab |
|
802dot11 OUI: none specified | |
| Stock bootloader | Breed |
| Expansion IF types | Mini PCIe, USB 2.0, SIM |
| SIM Card slot | 1 |
| Mini PCIe slots | 1 |
| USB ports | 1 |
| USB Hub Compatible | Untested |
| Power | 12 VDC, 1 A |
| Serial Port (UART) | yes |
|
Flags: | |
|
| |
| Other | |
|
| |
| 3rd Party Firmware Support |
OpenWrt • (List | Dev | DLs) |
| Radio 1 | |
| Chip1 | MediaTek MT7603E |
| Wireless interface OUI | none specified |
| Antenna Connector Type | none specified |
| MIMO status | 2x2:2 |
| Wireless Standard | IEEE 802.11b/g/n |
| 802.11n | up to 300 Mbps |
| 802.11g | up to 54 Mbps |
| 802.11b | up to 11 Mbps |
| WiFi Operating Frequency | 2.4 GHz |
| Radio 2 | |
| Chip1 | MediaTek MT7612 |
| Wireless interface OUI | none specified |
| Antenna Connector Type | none specified |
| MIMO status | 2x2:2 |
| Wireless Standard | IEEE 802.11a/n/ac |
| 802.11ac | up to 867 Mbps |
| 802.11n | up to 300 Mbps |
| 802.11a | up to 54 Mbps |
| WiFi Operating Frequency | 5 GHz |
For a list of all currently documented MediaTek chipsets with specifications, see MediaTek.
For a list of all currently documented UniElec devices with specifications, see UniElec.
Flashing
| NOTE: During configuration or flashing a device, the only things that should be hooked to the device is the computer and power. |
Flashing OpenWrt
Target: ramips
Subtarget: mt7621
Package architecture: mipsel_24kc
Supported Since Commit
Support started version: 21.02.0
Current supported version: 25.12.2
Subtarget: mt7621
Package architecture: mipsel_24kc
Supported Since Commit
Support started version: 21.02.0
Current supported version: 25.12.2
LAN Hardware: MediaTek MT7621AT
WLAN Hardware: MediaTek MT7603E, MediaTek MT7612
Installation method(s):
Sysupgrade, see git-commit
Recovery method(s):
Breed web recovery, see git-commit
WLAN Hardware: MediaTek MT7603E, MediaTek MT7612
Installation method(s):
Sysupgrade, see git-commit
Recovery method(s):
Breed web recovery, see git-commit
| git • >> |
|---|
ramips: add support for UniElec U7621-01 UniElec U7621-01 is a router platform board, the smaller model of the U7621-06. The device has the following specifications: - MT7621AT (880 MHz) - 256 of RAM (DDR3) - 16 MB of FLASH (SPI NOR) - 5x 1 Gbps Ethernet (MT7621 built-in switch) - 1x 2.4Ghz MT7603E - 1x 5Ghz MT7612 - 1x miniPCIe slots (PCIe bus only) - 1x miniSIM slot - 1x USB 2.0 (uses the usb 3.0 driver) - 8x LEDs (1x GPIO-controlled) - 1x reset button - 1x UART header (4-pins) - 1x GPIO header (30-pins) - 1x DC jack for main power (12 V) The following has been tested and is working: - Ethernet switch - 1x 2.4Ghz MT7603E (wifi) - 1x 5Ghz MT7612 (wifi) - miniPCIe slots (tested with Wi-Fi cards and LTE modem cards) - miniSIM slot (works with normal size simcard) - sysupgrade - reset button Installation: This board has no locked down bootloader. The seller can be asked to install openwrt v18.06, so upgrades are standard sysupgrade method. Recovery: This board contains a Chinese, closed-source bootloader called Breed (Boot and Recovery Environment for Embedded Devices). Breed supports web recovery and to enter it, you keep the reset button pressed for around 5 seconds during boot. Your machine will be assigned an IP through DHCP and the router will use IP address 192.168.1.1. The recovery website is in Chinese, but is easy to use. Click on the second item in the list to access the recovery page, then the second item on the next page is where you select the firmware. In order to start the recovery, you click the button at the bottom. LEDs list (left to right): - ESW_P0_LED_0 - ESW_P1_LED_0 - ESW_P2_LED_0 - ESW_P3_LED_0 - ESW_P4_LED_0 - CTS2_N (GPIO10, configured as "status" LED) - LED_WLAN# (connected with pin 44 in wifi1 slot) |
Pictures
Categories:
- UniElec
- Embedded system/wireless router
- Embedded System MediaTek
- Embedded System MT7621AT
- MediaTek
- Embedded System MIPS 1004Kc
- Embedded System
- OpenWrt Supported
- Embedded System MT7603E
- Has Mimo Status
- Embedded System IEEE 802.11b/g/n
- Embedded System MT7612
- Embedded System IEEE 802.11a/n/ac
- Dual-Radio Wireless Embedded System
- Wireless Embedded System
- Dual-Band
- English Documentation