Vimin VM-S100-0800MS
From TechInfoDepot
Jump to navigationJump to search
| 3rd Party Firmware | |
|---|---|
| dd-wrt | Status Unknown |
| OpenWrt | Supported |
| Tomato any flavor | Incompatible |
| Gargoyle | Status Unknown |
| Platform | |
| Brand • Model • Rev | Vimin VM-S100-0800MS |
CPU1  | Realtek RTL9303 |
| CPU1 Type | MIPS 34Kc |
| CPU1 Speed | 800 MHz |
| Flash1 Chip | Winbond W25Q128JVSQ |
| Flash1 Size | 16 MiB16,777,216 B <br />131,072 Kib <br />16,384 KiB <br />128 Mib <br />0.0156 GiB <br /> (SPI NOR) |
| RAM1 Size | 512 MiB536,870,912 B <br />4,194,304 Kib <br />524,288 KiB <br />4,096 Mib <br />0.5 GiB <br /> (DDR3) |
| ETH chip1 | Realtek RTL9303 |
| Switch | Realtek RTL9303 |
| Ethernet Port Count | 8- |
| Ethernet connector | SFP+ |
| Auto-MDIX | unspecified |
| Switch Class | managed |
|
Ethernet OUI: none specified | |
| Expansion IF types | none specified |
| Stock bootloader | U-Boot |
| Power | 100-240 VAC ~ 50/60 Hz, ? A |
| Connector type | AC (direct) |
| Serial Port (UART) | yes, 5V TTL, (115200 8N1) |
|
| |
| 3rd Party Firmware Support |
OpenWrt • (List | Dev | DLs) |
For a list of all currently documented Realtek chipsets with specifications, see Realtek.
Flashing
 | NOTE: During configuration or flashing a device, the only things that should be hooked to the device is the computer and power. |
Flashing OpenWrt
Target: realtek
Subtarget: rtl930x
Package architecture: mips_24kc
Supported Since Commit
Support started version: 25.12.0
Current supported version: 25.12.1
Subtarget: rtl930x
Package architecture: mips_24kc
Supported Since Commit
Support started version: 25.12.0
Current supported version: 25.12.1
LAN Hardware: Realtek RTL9303
WLAN Hardware: none
Installation method(s):
see git-commit
Recovery method(s):
see git-commit
WLAN Hardware: none
Installation method(s):
see git-commit
Recovery method(s):
see git-commit
| git • >> |
|---|
realtek: add support for Vimin VM-S100-0800MS
Vimin VM-S100-0800MS is an 8 port Multi-Gig switch, based on RTL9303.
Ported from XikeStor SKS8300-8X with changes to support different u-boot
build.
Specification:
- SoC : Realtek RTL9303
- RAM : DDR3 512 MiB
- Flash : SPI-NOR 16 MiB (Winbond W25Q128JVSQ)
- Ethernet : 8x 1/2.5/10 Gbps (SFP+)
- LEDs/Keys (GPIO): 0x/1x
- UART : "Console" port on the front panel
- type : RS-232C
- connector : RJ-45
- settings : 115200n8
- Power : AC100-240V 50/60Hz
Flash instruction using initramfs image:
1. Prepare TFTP server with an IP address "192.168.1.111"
2. Connect your PC to Port1 on VM-S100-0800MS
3. Power on VM-S100-0800MS and interrupt boot by pressing Esc
4. Enable Port1 with the following commands
rtk 10g 0 fiber1g (or fiber10g if 10GBase-*R, dac300cm for DAC cable)
rtk ext-devInit 0
rtk ext-pinSet 2 0
Note: the last command sets tx-disable to low
7. Download initramfs image from TFTP server
tftpboot 0x82000000 <image name>
8. Boot with the downloaded image
bootm
9. On the initramfs image, backup the stock firmware if needed
10. Upload (or download) sysupgrade image to the device
11. Erase "firmware" partition to cleanup JFFS2 of stock FW
mtd erase firmware
12. Perform sysupgrade with the sysupgrade image
13. Wait ~120 sec to complete flashing
Reverting to stock firmware:
1. Prepare by downloading the stock firmware. Vimin doesn't have
the firmware on their website, tested using firmware for shared
hardware Nicgiga S100-0800S-M.
Filename: vmlinux-nicgiga-S100-0800S-M-241126EN.bix
2. Prepare TFTP server with an IP address "192.168.1.111"
3. Connect your PC to Port1 on VM-S100-0800MS
4. Power on VM-S100-0800MS and interrupt boot by pressing Esc
5. Enable Port1 with the following commands
rtk 10g 0 fiber1g (or fiber10g if 10GBase-*R, dac300cm for DAC cable)
rtk ext-devInit 0
rtk ext-pinSet 2 0
Note: the last command sets tx-disable to low
6. Download initramfs image from TFTP server
tftpboot 0x82000000 <image name>
7. Boot with the downloaded image
bootm
8. Under Management -> Firmware -> Upgrade/Backup, upload bix file.
9. Reboot device
|
