EnGenius ESR600H

multiple revisions of this device, use caution

abgn (AN600)
Xtra Range Dual Band N600 Gigabit Router
WikiDevi.wi-cat.ru	EnGenius ESR600H
3rd Party Firmware
dd-wrt	Status Unknown
OpenWrt	Supported
Tomato any flavor	Incompatible
Gargoyle	Status Unknown
Platform
Brand • Model • Rev	EnGenius ESR600H
FCC ID	A8JESR600H, A8JESR750H
IC ID	10103A-ESR600H
Type	wireless router
CPU1 Y	Ralink RT3662
CPU1 Type	MIPS 74Kc
CPU1 Speed	500 MHz
Flash1 Chip	Macronix MX25L6406EM2I-12G
Flash1 Size	8 MiB 8,388,608 B <br />65,536 Kib <br />8,192 KiB <br />64 Mib <br />0.00781 GiB <br />
RAM1 Size	64 MiB 67,108,864 B <br />524,288 Kib <br />65,536 KiB <br />512 Mib <br />0.0625 GiB <br />
RAM1 Chip	Nanya NT5TU32M16DG-AC
ETH chip1	Ralink RT3662
Switch	Atheros AR8327
Ethernet Port Count	1-1GbE-WAN 4-1GbE-LAN
Wired Standard	IEEE 802.3i/3u/3ab
802dot11 OUI: 00:02:6F (27 E, 62 W) Ethernet OUI: 00:02:6F (27 E, 62 W)
Stock bootloader	U-Boot 1.0.6.198
Stock FW OS	Linux 2.6.21
Expansion IF types	USB 2.0
USB ports	1
USB Hub Compatible	Untested
Power	12 VDC, 1.25 A
Connector type	barrel
Serial Port (UART)	yes, 4-pin header
Other
Default SSID: EnGeniusXXXXXX (16 addl. devices) , EnGeniusXXXXXX_5G Default IP address: 192.168.0.1 the IP 192.168.0.1 is used by 825 additional devices of which 26 are EnGenius devices Default login user: admin Default login password: admin admin:admin credentials used by 1358 additional devices of which 49 are EnGenius devices
Manuf/OEM/ODM	Senao
3rd Party Firmware Support	OpenWrt • (List | Dev | DLs)
Retail
Availability	End of Life
FCC approval date	03 May 2012
UPC	666672922646 (UPC DB, On eBay)
ASIN	B007IGLSFA
Country of manuf	Taiwan
Radio 1
Chip1	Ralink RT3662
Wireless interface OUI	00:02:6F
Antenna Connector Type	U.FL
MIMO status	2x2:2
Wireless Standard	IEEE 802.11a/n
802.11n	up to 300 Mbps
802.11a	up to 54 Mbps
WiFi Operating Frequency	5 GHz
Radio 2
Chip1	Ralink RT5392
Wireless interface OUI	00:02:6F
Antenna Connector Type	U.FL, RP-SMA
MIMO status	2x2:2
Wireless Standard	IEEE 802.11b/g/n
802.11n	up to 300 Mbps
802.11g	up to 54 Mbps
802.11b	up to 11 Mbps
WiFi Operating Frequency	2.4 GHz
FCC ID EnGenius ESR750H A8JESR750H
CPU1 brand Radio1 chip1 brand Radio2 chip1 brand EnGenius ESR600 MediaTek MediaTek Ralink EnGenius ESR600H Ralink Ralink Ralink

For a list of all currently documented Atheros (QCA) chipsets with specifications, see Atheros.
For a list of all currently documented Ralink chipsets with specifications, see Ralink.

For a list of all currently documented EnGenius devices with specifications, see EnGenius.

• 300 Mbps - 2SS 2.4GHz 802.11n (40MHz chan.),

• 300 Mbps - 2SS 5GHz 802.11n (40MHz chan.) = AN600 class

Overview

The default SSID formats appear to be EnGeniusXXXXXX and EnGeniusXXXXXX_5G.

Links of Interest

Datasheet

On uk.hardware.info' (w/ internal shot)

"7016A0515018 Ver: 1.10" is silkscreened on the board.

• CES 2012: EnGenius Launches Long-Range N Router Line - SmallNetBuilder

Flashing

Flashing OpenWrt

On the OpenWrt ToH (techdata entry)

Target: ramips
Subtarget: rt3883
Package architecture: mipsel_74kc
Supported Since Commit
Support started version: 21.02.0
Current supported version: 25.12.1

LAN Hardware: Atheros AR8327
WLAN Hardware: Ralink RT3662F, Ralink RT5392L
WLAN Comment: MIMO 2x2:2 on both bands
Installation method(s):
GUI OEM, U-Boot TFTP recovery, see git-commit
Recovery method(s):
U-Boot TFTP + serial recovery

git • >>

ramips: add support for Senao Engenius ESR600H FCC ID: A8J-ESR750H Engenius ESR600H is an indoor wireless router with a gigabit switch, 2.4 GHz and 5 GHz wireless, internal and external antennas, and a USB port. **Specification:** - RT3662F MIPS SOC, 5 GHz WMAC (2x2) - RT5392L PCI on-board, 2.4 GHz (2x2) - AR8327 RGMII, 7-port GbE, 25 MHz clock - 40 MHz reference clock - 8 MB FLASH 25L6406EM2I-12G - 64 MB RAM - UART at J12 (unpopulated) - 2 internal antennas (5 GHz) - 2 external antennas (2.4 GHz) - 9 LEDs, 1 button (power, wps, wifi2g, wifi5g, 5 LAN/WAN) - USB 2 port (GPIO controlled power) **MAC addresses:** MAC Addresses are labeled as WAN and WLAN U-boot environment has the the vendor MAC address for ethernet MAC addresses in "factory" are part of wifi calibration data eth0.2 WAN *:13:e7 u-boot-env wanaddr eth0.1 ---- *:13:e8 u-boot-env wanaddr + 1 phy0 WLAN *:14:b8 factory 0x8004 phy1 ---- *:14:bc factory 0x4 **Installation:** Method 1: Firmware upgrade page OEM webpage at 192.168.0.1 username and password "admin" Navigate to Network Setting --> Tools --> Firmware Click Browse and select the factory.dlf image Click Continue to confirm and wait 6 minutes or more... Method 2: Serial console to load TFTP image: (see TFTP recovery) **Return to OEM:** Unlike most Engenius boards, this does not have a 'failsafe' image the only way to return to OEM is serial access to uboot Unlike most Engenius boards, public images are not available... so the only way to return to OEM is to have a copy of the MTD partition "firmware" BEFORE flashing openwrt. **TFTP recovery:** Unlike most Engenius boards, TFTP is reliable here however it requires serial console access (soldering pins to the UART pinouts) build your own image... with 'ramdisk' selected under 'Target Images' rename initramfs-kernel.bin to 'uImageESR-600H' make the file available on a TFTP server at 192.168.99.8 interrupt boot by holding or pressing '4' in serial console as soon as board is powered on `tftpboot 0x81000000` `bootm 0x81000000` perform a sysupgrade **Format of OEM firmware image:** This Engenius board uses the Senao proprietary header with a unique Product ID. The header for factory.bin is generated by the mksenaofw program included in openwrt. .dlf file extension is also required for OEM software to accept it **Note on using OKLI:** the kernel is now too large for the bootloader to handle so OKLI is used via the `kernel-loader` image command recently in master several other ramips boards have the same problem 'Kernel panic - not syncing: Failed to find ralink,rt3883-sysc node' see commit ad19751edc21ae713bd95df6b93be64bd1e0c612