Huasifei WH3000

multiple revisions of this device, use caution

abgn+ac+ax (AX1800)
Portable Wi-Fi 6 travel router
Homepage	Product page
3rd Party Firmware
dd-wrt	Status Unknown
OpenWrt	Supported
Tomato any flavor	Incompatible
Gargoyle	Status Unknown
Platform
Brand • Model • Rev	Huasifei WH3000
FCC ID	none specified
Type	travel router
CPU1 Y	MediaTek MT7981A
CPU1 Type	ARM Cortex-A53
CPU1 Speed	1.3 GHz ( 2 cores ) 64-bit
Flash1 Chip	Brand? Model?
Flash1 Size	8 GiB 8,192 MiB <br />8,589,934,592 B <br />67,108,864 Kib <br />8,388,608 KiB <br />65,536 Mib <br /> (eMMC)
RAM1 Size	1 GiB 1,024 MiB <br />1,073,741,824 B <br />8,388,608 Kib <br />1,048,576 KiB <br />8,192 Mib <br /> (DDR4)
RAM1 Chip	Brand? Model?
ETH chip1	MediaTek MT7981A
ETH chip2	Realtek RTL8221B
Ethernet Port Count	1-2.5GbE-WAN 1-1GbE-LAN
Wired Standard	IEEE 802.3i/3u/3ab/3bz
802dot11 OUI: none specified
Stock bootloader	U-Boot
Expansion IF types	USB 3.0
USB ports	1
USB Hub Compatible	Untested
Power	5 VDC, 3 A
Connector type	USB (Type-C)
Serial Port (UART)	yes, 3.3V TTL, (115200 8N1)
Flags: Wi-Fi 6
Other
3rd Party Firmware Support	OpenWrt • (List | Dev | DLs)
Radio 1
Chip1	MediaTek MT7981A
Chip2	MediaTek MT7976CN
Wireless interface OUI	none specified
Antenna Connector Type	none specified
MIMO status	2x2:2
Wireless Standard	IEEE 802.11b/g/n/ax
802.11ax	up to 574 Mbps
802.11n	up to 300 Mbps
802.11g	up to 54 Mbps
802.11b	up to 11 Mbps
WiFi Operating Frequency	2.4 GHz
Radio 2
Chip1	MediaTek MT7981A
Chip2	MediaTek MT7976CN
Wireless interface OUI	none specified
Antenna Connector Type	none specified
MIMO status	3x3:2
Wireless Standard	IEEE 802.11a/n/ac/ax
802.11ax	up to 1201 Mbps
802.11ac	up to 867 Mbps
802.11n	up to 300 Mbps
802.11a	up to 54 Mbps
CPU1 brand Radio1 chip1 brand Radio2 chip1 brand Huasifei WH3000 MediaTek MediaTek MediaTek Huasifei WH3000 Pro MediaTek MediaTek MediaTek

For a list of all currently documented MediaTek chipsets with specifications, see MediaTek.
For a list of all currently documented Realtek chipsets with specifications, see Realtek.

• 574 Mbps - 2SS 2.4GHz 802.11ax (40MHz chan., 256-QAM),

• 1201 Mbps - 2SS 5GHz 802.11ax (80MHz chan., 1024-QAM) = AX1800 class

Flashing

Flashing OpenWrt

On the OpenWrt ToH (techdata entry)

Target: mediatek
Subtarget: filogic
Package architecture: aarch64_cortex-a53
Supported Since Commit
Support started version: 24.10.1
Current supported version: 24.10.5

LAN Hardware: MediaTek MT7981A
LAN Comment: Realtek RTL8221B 2.5GbE Phy
WLAN Hardware: MediaTek MT7981A, MediaTek MT7976CN
Installation method(s):
see git-commit
Recovery method(s):
see git-commit

git • >>

mediatek: filogic: add support for Huasifei WH3000 **Huasifei WH3000 eMMC / Fudy MT3000** Portable Wi-Fi 6 travel router based on MediaTek MT7981A SoC. MT7981B+MT7976CN+RTL8221B Dual Core 1.3GHZ **Specifications** SoC: Filogic 820 MT7981A (1.3GHz) RAM: DDR4 1GB Flash: eMMC 8GB WiFi: 2.4GHz and 5GHz with 3 antennas Ethernet: 1x WAN (10/100/1000M) 1x LAN (10/100/1000/2500M) USB: 1x USB 3.0 port Two buttons: power/reset and mode (BTN_0) LEDS: blue, red, blue+red=pink UART: 3.3V, TX, RX, GND / 115200 8N1 **Installation via U-Boot rescue** 1. Set static IP 192.168.1.2 on your computer and default route as 192.168.1.1 2. Connect to the WAN port and hold the reset button while booting the device. 3. Wait for the LED to blink 5 times, and release the reset button. 4. Open U-boot web page on your browser at http://192.168.1.1 5. Select the OpenWRT sysupgrade image, upload it, and start the upgrade. 6. Wait for the router to flash the new firmware. 7. Wait for the router to reboot itself. **Installation via sysupgrade** Just flash sysupgrade file via [LuCI upgrade page](http://192.168.1.1/cgi-bin/luci/admin/system/flash) without saving the settings. **Installation via SSH** Upload the file to the router `/tmp` directory, `ssh root@192.168.1.1` and issue a command: ``` sysupgrade -n /tmp/openwrt-mediatek-filogic-huasifei_wh3000-emmc-squashfs-sysupgrade.bin ``` **Factory MAC** You can find your Factory MAC which is mentioned on the box at `/dev/mmcblck0p2` partition `factory` starting from `0x4` ``` dd if=/dev/mmcblk0p2 bs=1 skip=4 count=6 | hexdump -C ``` **Enlarging a partition** Though device has 8GB eMMC, it uses only 2GB `/dev/mmcblck0p6` as `rootfs` for `/rom` and `/overlay` leaving `/dev/mmcblck0p7` as empty unused space. ``` sgdisk -p /dev/mmcblk0 ``` ``` Disk /dev/mmcblk0: 15269888 sectors, 7.3 GiB Sector size (logical/physical): 512/512 bytes Disk identifier (GUID): 2BD17853-102B-4500-AA1A-8A21D4D7984D Partition table holds up to 128 entries Main partition table begins at sector 2 and ends at sector 33 First usable sector is 34, last usable sector is 14942174 Partitions will be aligned on 1024-sector boundaries Total free space is 11197 sectors (5.5 MiB) Number Start (sector) End (sector) Size Code Name 1 8192 9215 512.0 KiB 8300 u-boot-env 2 9216 13311 2.0 MiB 8300 factory 3 13312 21503 4.0 MiB 8300 fip 4 21504 29695 4.0 MiB 8300 config 5 29696 62463 16.0 MiB 8300 kernel 6 62464 4256767 2.0 GiB 8300 rootfs 7 4257792 14940159 5.1 GiB 8300 ``` You can fix that by loading into `initramfs-kernel`, deleting empty `mmcblck0p7` partition and resizing `mmcblck0p6` ``` sysupgrade -F /tmp/openwrt-initramfs-kernel.bin ``` Install and run cfdisk ``` opkg update && opkg install cfdisk cfdisk /dev/mmcblck0 ``` - Select `mmcblck0p7` -> Delete - Select `mmcblck0p6` -> Resize -> Write -> yes -> Quit You will not see any difference in `cat /proc/partitions` after that but just flash a `sysupgrade` and you'll get the whole 7.3GB space for the `/overlay`. Co-developed-by: hecatae Signed-off-by: Fil Dunsky Link: https://github.com/openwrt/openwrt/pull/18220 Signed-off-by: Hauke Mehrtens