Linksys MR7340

abgn+ac+ax (AX1800)
Max-stream AX1500
Wikipedia	Linksys routers
3rd Party Firmware
dd-wrt	Status Unknown
OpenWrt	Supported
Tomato any flavor	Incompatible
Gargoyle	Status Unknown
Platform
Brand • Model • Rev	Linksys MR7340
FCC ID	Q87-08151
Type	wireless router
CPU1 Y	Qualcomm IPQ6028
CPU1 Type	ARM Cortex-A53
CPU1 Speed	1.2 GHz ( 4 cores )
Flash1 Chip	Brand? Model?
Flash1 Size	256 MiB268,435,456 B <br />2,097,152 Kib <br />262,144 KiB <br />2,048 Mib <br />0.25 GiB <br /> (NAND)
Flash2 Size	32 MiB33,554,432 B <br />262,144 Kib <br />32,768 KiB <br />256 Mib <br />0.0313 GiB <br />
RAM1 Size	512 MiB536,870,912 B <br />4,194,304 Kib <br />524,288 KiB <br />4,096 Mib <br />0.5 GiB <br /> (DDR3)
RAM1 Chip	Brand? Model?
ETH chip1	Qualcomm IPQ6028
Switch	Qualcomm Atheros QCA8075
Ethernet Port Count	1-1GbE-WAN 4-1GbE-LAN
Wired Standard	IEEE 802.3i/3u/3ab
Port-based vlan	yes
802.1q vlan	yes
802dot11 OUI: none specified
Stock bootloader	U-Boot
Expansion IF types	USB 3.0
USB ports	1
USB Hub Compatible	Untested
Power	12 VDC, 2.0 A
Connector type	barrel
Serial Port (UART)	yes, 3.3, 115200 / 8N1
JTAG Port	yes
Flags: Wi-Fi 6
Other
3rd Party Firmware Support	OpenWrt • (List | Dev | DLs)
Radio 1
Chip1	Qualcomm IPQ6028
Chip2	Qualcomm QCN5022
Wireless interface OUI	none specified
Antenna Connector Type	none specified
MIMO status	2x2:2
Wireless Standard	IEEE 802.11b/g/n/ax
802.11ax	up to 574 Mbps
802.11n	up to 300 Mbps
802.11g	up to 54 Mbps
802.11b	up to 11 Mbps
WiFi Operating Frequency	2.4 GHz
Radio 2
Chip1	Qualcomm IPQ6028
Chip2	Qualcomm QCN5052
Wireless interface OUI	none specified
Antenna Connector Type	none specified
MIMO status	2x2:2
Wireless Standard	IEEE 802.11a/n/ac/ax
802.11ax	up to 1201 Mbps
802.11ac	up to 867 Mbps
802.11n	up to 300 Mbps
802.11a	up to 54 Mbps
WiFi Operating Frequency	5 GHz
FCC ID Linksys MR7310 Q87-08151 Linksys MR7320 Q87-08151 Linksys MR7350 Q87-08151

For a list of all currently documented Qualcomm chipsets with specifications, see Qualcomm.
For a list of all currently documented Qualcomm Atheros (QCA) chipsets with specifications, see Qualcomm Atheros.

For a list of all currently documented Linksys devices with specifications, see Linksys.

• 574 Mbps - 2SS 2.4GHz 802.11ax (40MHz chan., 256-QAM),

• 1201 Mbps - 2SS 5GHz 802.11ax (80MHz chan., 1024-QAM) = AX1800 class

Flashing

Flashing OpenWrt

On the OpenWrt ToH (techdata entry)
On the OpenWrt Wiki

Target: qualcommax
Subtarget: ipq60xx
Package architecture: aarch64_cortex-a53
Supported Since Commit
Support started version: 25.12.0
Current supported version: 25.12.6

LAN Hardware: Qualcomm Atheros QCA8075
WLAN Hardware: Qualcomm QCN5022, Qualcomm QCN5052
WLAN Comment: MIMO 2x2:2 on both bands
Install Comment:
GUI OEM, see devicepage, see git-commit
Recovery Comment:
see devicepage, see git-commit

git • >>

qualcommax: ipq60xx: add Linksys MR7350 support Linksys MR7350 is a 802.11ax Dual-band router/AP. Specifications: * CPU: Qualcomm IPQ6000 Quad core Cortex-A53(A73) 1.5GHz * RAM: 512MB of DDR3 * Storage: 256Mb NAND * Ethernet: 5x1G RJ45 ports (QCA8075) * WLAN: * 2.4GHz: Qualcomm QCN5022 2x2 802.11b/g/n/ax 574 Mbps PHY rate * 5GHz: Qualcomm QCN5052 2x2@80MHz or 802.11a/b/g/n/ac/ax 1201 Mbps PHY rate * LED-s: * RGB system led * USB blue led * Buttons: 1x Soft reset 1x WPS * Power: 12V DC Jack Installation instructions: Open Linksys Web UI - http://192.168.1.1/ca or http://10.65.1.1/ca depending on your setup. Login with your admin password. The default password can be found on a sticker under the device. To enter into the support mode, click on the “CA” link and the bottom of the page. Open the “Connectivity” menu and upload the squash-factory image with the “Choose file” button. Click start. Ignore all the prompts and warnings by click “yes” in all the popups. The Wifi radios are turned off by default. To configure the router, you will need to connect your computer to the LAN port of the device. Then you would need to write openwrt to the other partition for it to work - First Check booted partition: fw_printenv -n boot_part - Change the partition: fw_setenv boot_part 1 or fw_setenv boot_part 2 depending on the current partition - Then install Openwrt to the other partition if booted in slot 1: mtd -r -e alt_kernel -n write openwrt-qualcommax-ipq60xx-linksys_mr7350-squashfs-factory.bin alt_kernel - If in slot 2: mtd -r -e kernel -n write openwrt-qualcommax-ipq60xx-linksys_mr7350-squashfs-factory.bin kernel Co-Authored-by: Chukun Pan Co-Authored-by: Robert Marko Signed-off-by: Vladyslav Andreichykov Link: https://github.com/openwrt/openwrt/pull/14807 Signed-off-by: Robert Marko