SolidRun ClearFog CN9130 Pro
From TechInfoDepot
Jump to navigationJump to search
| Single Board Computer | |||||||||||||||||||||
|
| |||||||||||||||||||||
| Homepage | Product page | ||||||||||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| 3rd Party Firmware | |||||||||||||||||||||
| dd-wrt | Status Unknown | ||||||||||||||||||||
| OpenWrt | Supported | ||||||||||||||||||||
| Tomato any flavor | Incompatible | ||||||||||||||||||||
| Gargoyle | Status Unknown | ||||||||||||||||||||
| Platform | |||||||||||||||||||||
| Brand • Model • Rev | SolidRun ClearFog CN9130 Pro | ||||||||||||||||||||
| Type | single-board computer | ||||||||||||||||||||
| CPU1 | Marvell CN9130 | ||||||||||||||||||||
| CPU1 Type | ARMv8 Cortex-A72 | ||||||||||||||||||||
| CPU1 Speed | 2.0 GHz ( 4 cores ) | ||||||||||||||||||||
| Flash1 Chip | Brand? Model? | ||||||||||||||||||||
| Flash1 Size | 8 GiB 8,192 MiB <br />8,589,934,592 B <br />67,108,864 Kib <br />8,388,608 KiB <br />65,536 Mib <br /> (eMMC) | ||||||||||||||||||||
| Flash2 Size | 8 MiB8,388,608 B <br />65,536 Kib <br />8,192 KiB <br />64 Mib <br />0.00781 GiB <br /> (SPI NOR) | ||||||||||||||||||||
| RAM1 Size | 4 GiB 4,096 MiB <br />4,294,967,296 B <br />33,554,432 Kib <br />4,194,304 KiB <br />32,768 Mib <br /> | ||||||||||||||||||||
| RAM1 Chip | Brand? Model? | ||||||||||||||||||||
| ETH chip1 | Marvell CN9130 | ||||||||||||||||||||
| Switch | Marvell 88E6393X | ||||||||||||||||||||
| Ethernet Port Count |
1-1GbE-WAN 5-1GbE-LAN | ||||||||||||||||||||
| Wired Standard | IEEE 802.3i/3u/3ab | ||||||||||||||||||||
|
| |||||||||||||||||||||
| Stock bootloader | U-Boot | ||||||||||||||||||||
| Expansion IF types | eMMC, microSDHC, Mini PCIe (2x mSATA/mPCIE with SIM holder), USB 3.0, SIM, SATA (via M.2 2242 slot), SFP+ | ||||||||||||||||||||
| SIM Card slot | 1 | ||||||||||||||||||||
| Mini PCIe slots | 2 | ||||||||||||||||||||
| USB ports | 1 | ||||||||||||||||||||
| SD/MMC Slots | 1 | ||||||||||||||||||||
| SATA Ports | 1 | ||||||||||||||||||||
| SFP ports | 1 | ||||||||||||||||||||
| M.2 Slots | 1 | ||||||||||||||||||||
| USB Hub Compatible | Untested | ||||||||||||||||||||
| Power | 9-32 VDC, ? A | ||||||||||||||||||||
| Connector type | barrel | ||||||||||||||||||||
| Serial Port (UART) | yes, 5V TTL, (115200 8N1) | ||||||||||||||||||||
|
| |||||||||||||||||||||
|
| |||||||||||||||||||||
| Other | |||||||||||||||||||||
|
| |||||||||||||||||||||
| 3rd Party Firmware Support |
OpenWrt • (List | Dev | DLs) | ||||||||||||||||||||
| |||||||||||||||||||||
For a list of all currently documented Marvell chipsets with specifications, see Marvell.
For a list of all currently documented SolidRun devices with specifications, see SolidRun.
Flashing
| NOTE: During configuration or flashing a device, the only things that should be hooked to the device is the computer and power. |
Flashing OpenWrt
Target: mvebu
Subtarget: cortexa72
Package architecture: aarch64_cortex-a72
Supported Since Commit
Support started version: 24.10.0
Current supported version: 24.10.5
Subtarget: cortexa72
Package architecture: aarch64_cortex-a72
Supported Since Commit
Support started version: 24.10.0
Current supported version: 24.10.5
LAN Hardware: Marvell 88E6393X
WLAN Comment: WLAN dependent on mPCIe installed
Installation method(s):
see git-commit
Recovery method(s):
see git-commit
Comment:
mikroBUS expansion connector
WLAN Comment: WLAN dependent on mPCIe installed
Installation method(s):
see git-commit
Recovery method(s):
see git-commit
Comment:
mikroBUS expansion connector
| git • >> |
|---|
mvebu: add support for SolidRun ClearFog Pro The SolidRun ClearFog Pro is a router based on the SolidRun CN9130 SOM. Specs: - SoC: Quad-Core Cortex-A72 CN9130 SoC - RAM: 4GiB DDR4 - Serial: Micro-USB port on front (FT232R, 115200 8n1) - Storage: 8GiB eMMC, microSD card slot, 8MiB SPI NOR flash - Ethernet: 7x GbE (1 port dedicated on SoC, 6 port switch with single GbE CPU port) - SFP: 1x SFP+ - USB: 1x USB-A 3.1 Gen 1 - PCIe: 2x mini PCIe (one slot with USB and SIM card socket) - SATA: 1x M.2 Key-B In addition to the usual connectivity options this device also features an internal mikroBUS expansion connector. SATA is currently untested due to lack of a suitable M.2 SSD. Installation ============ 1. Write sdcard sysupgrade image to microSD card using dd or similar 2. Insert microSD card into router and apply power 3. Device boots into OpenWRT 4. (optional) dd sysupgrade image to /dev/mmcblk0 to install to eMMC |