ZyXEL XGS1210-12
From TechInfoDepot
Jump to navigationJump to search
|
Multi-Gig 12-Port Web Managed Switch with 2-Port 2.5G/2-Port 10G SFP+ | ||||||||||
 | ||||||||||
| WikiDevi.wi-cat.ru | ZyXEL XGS1210-12 | |||||||||
|---|---|---|---|---|---|---|---|---|---|---|
| 3rd Party Firmware | ||||||||||
| dd-wrt | Status Unknown | |||||||||
| OpenWrt | Supported | |||||||||
| Tomato any flavor | Incompatible | |||||||||
| Gargoyle | Status Unknown | |||||||||
| Platform | ||||||||||
| Brand • Model • Rev | ZyXEL XGS1210-12 rev A1 | |||||||||
| Board ID | 2976958502 | |||||||||
CPU1  | Realtek RTL9302B | |||||||||
| CPU1 Type | MIPS 34Kc | |||||||||
| CPU1 Speed | 800 MHz | |||||||||
| Flash1 Chip | Macronix MX25L12833F | |||||||||
| Flash1 Size | 16 MiB 16,777,216 B <br />131,072 Kib <br />16,384 KiB <br />128 Mib <br />0.0156 GiB <br /> (SPI NOR) | |||||||||
| RAM1 Size | 128 MiB 134,217,728 B <br />1,048,576 Kib <br />131,072 KiB <br />1,024 Mib <br />0.125 GiB <br /> (DDR3) | |||||||||
| RAM1 Chip | Nanya NT5CC64M16GP-1 | |||||||||
| ETH chip1 | Realtek RTL9302B | |||||||||
| ETH chip2 | Realtek RTL8218D | |||||||||
| ETH chip3 | Realtek RTL8226 | |||||||||
| ETH chip4 | Realtek RTL8226 | |||||||||
| Switch | Realtek RTL9302B | |||||||||
| Ethernet Port Count | 12-1GbE | |||||||||
| Ethernet connector | 8P8C | |||||||||
| Wired Standard | IEEE 802.3i/3u/3ab/3bz/an | |||||||||
| Auto-MDIX | supported | |||||||||
| Jumbo frame | yes | |||||||||
| Switch Class | managed | |||||||||
| Expansion IF types | SFP+ | |||||||||
| SFP ports | 2 | |||||||||
| Stock bootloader | U-Boot V1.0.0.1 | |||||||||
| Stock FW OS | Linux 5.4.70 | |||||||||
| Power | 12 VDC, 1.5 A | |||||||||
| Connector type |
barrel 5.5 mm (OD) 2.1 mm (ID) 9.5 mm (LEN) | |||||||||
| Serial Port (UART) | yes, 4-pin header, J5, 3.3V TTL, (115200 8N1) | |||||||||
| JTAG Port | yes, 14-pin header, J2 | |||||||||
| Other | ||||||||||
|
Default IP address: 192.168.1.3 | ||||||||||
| Manuf/OEM/ODM | Delta Networks | |||||||||
|
Flags: SFP+ (10GbE), Smart switch, metal case, heatsink | ||||||||||
| 3rd Party Firmware Support |
OpenWrt • (List | Dev | DLs) | |||||||||
|
Additional chips | ||||||||||
| Retail | ||||||||||
| (Est.) release date | December 2019 | |||||||||
| (Est.) initial retail price (in USD) | $298 | |||||||||
| Newegg | N82E16833181565 | |||||||||
| UPC |
760559126827 (UPC DB, On eBay) | |||||||||
| EAN |
4718937610785 (UPC DB, On eBay) | |||||||||
| ASIN |
B084MH9P8Q  | |||||||||
| Country of manuf | China | |||||||||
| ||||||||||
For a list of all currently documented Realtek chipsets with specifications, see Realtek.
For a list of all currently documented ZyXEL devices with specifications, see ZyXEL.
Overview
Specifications
- Processor: Realtek RTL9302B @800MHz (MIPS 34Kc)
- Multi-Layer Managed Switch Controller with Embedded CPU
- Flash/RAM: 16MB (SPI NOR) Flash, 128MB RAM (DDR3)
- Ethernet: 8x Gigabit Ethernet ports, 2x 2.5Gigabit Ethernet ports,
- 2x SFP+ (10GbE) slots
- Switching Capacity: 66 Gbps
- Switching Forwarding Rate: 49 Mpps
Links of Interest
- PCB ID: 2976958502 (OEM: Delta Networks)
Flashing
 | NOTE: During configuration or flashing a device, the only things that should be hooked to the device is the computer and power. |
Flashing OpenWrt
Target: realtek
Subtarget: rtl930x
Package architecture: mips_24kc
Supported Since Commit
Support started version: 25.12.0
Current supported version: 25.12.1
Subtarget: rtl930x
Package architecture: mips_24kc
Supported Since Commit
Support started version: 25.12.0
Current supported version: 25.12.1
LAN Hardware: Realtek RTL9302B
LAN Comment: 2x RTL8226 2.5Gbe Phy
WLAN Hardware: none
WLAN Comment: No WLAN
Installation method(s):
see git-commit
Recovery method(s):
see git-commit
LAN Comment: 2x RTL8226 2.5Gbe Phy
WLAN Hardware: none
WLAN Comment: No WLAN
Installation method(s):
see git-commit
Recovery method(s):
see git-commit
| git • >> |
|---|
realtek: Add support for Zyxel XGS1210-12 Switch The Zyxel XGS1210-12 Switch is a 10 + 2 port multi-GBit switch with 8 x 1000BaseT, 2 x 10/100/1000/2500BaseT Ethernet ports and 2 SFP+ module slot. Hardware: - RTL9302B SoC - Macronix MX25L12833F (16MB flash) - Nanja NT5CC64M16GP-1 (128MB DDR3 SDRAM) - RTL8231 GPIO extender to control the port LEDs - RTL8218D 8x Gigabit PHY - RTL8226 2x 10m/100m/1/2.5 Gigabit PHY - SFP+ 2x 10GBit slot Power is supplied via a 12V 1.5A standard barrel connector. At the right side behind the grid is UART serial connector. A Serial header can be connected to from the outside of the switch trough the airvents with a standard 2.54mm header. Pins are from top to bottom Vcc(3.3V), TX, RX and GND. Serial connection is via 115200 baud, 8N1. A reset button is accessble through a hole in the front panel At the time of this commit, all ethernet ports work under OpenWrt, including the various NBaseT modes, SFP+ slots are supported with i2c bus. Installation -------------- * Connect serial as per the layout above. Connection parameters: 115200 8N1. * Navigate to 'Management' in the OEM web interface and click on 'Firmware upgrade' to the left. * Upload the OpenWrt initramfs image, and wait till the switch reboots. * Connect to the device through serial and change the U-boot boot command. > fw_setenv bootcmd 'rtk network on; boota' * Reboot, scp the sysupgrade image to /tmp, verify the checksum and flash it: > sysupgrade openwrt-realtek-rtl930x-Zyxel_xgs1210-12-squashfs-sysupgrade.bin * Upon reboot, you have a functional OpenWrt installation. Leave the bootcmd value as is - without 'rtk network on' the switch will fail to initialise the network. Debug ------------ * Connect serial as per the layout above. Connection parameters: 115200 8N1. * A tftp server is requiered, tftpd-hpa works well. * Power the device, at U-Boot start rapidly hit Esc key to stop autoboot * Enable network: > rtk network on * Change ip address (default is 192.168.1.1): > setenv ipaddr 192.168.1.6 * Download initramfs: > tftpboot 0x84f00000 192.168.1.111:openwrt-realtek-rtl930x-Zyxel_xgs1210-12-initramfs-kernel.bin * Boot loaded file: > bootm 0x84f00000 This prodecudre also apply to the sock firmware with the file XGS1210-12_V2.00(ABTY.1)C0.bix. More information can be found on the page of XGS1250-12 as they share the same base. |
Pictures
-
Board Top -
Board Bottom
