ZyXEL GS1900-24E

From TechInfoDepot
Jump to navigationJump to search
multiple revisions of this device, use caution
24-port GbE Smart Managed Switch
Homepage Product page
WikiDevi.wi-cat.ru ZyXEL GS1900-24E
3rd Party Firmware
dd-wrt Status Unknown
OpenWrt Supported
Tomato any flavor Incompatible
Gargoyle Status Unknown
Platform
Brand • Model • Rev ZyXEL GS1900-24E rev A1
CPU1 checkY Realtek RTL8382M
CPU1 Type MIPS 4KEc
CPU1 Speed 500 MHz
Flash1 Chip Macronix MX25L12835F
Flash1 Size 16 MiB 16,777,216 B <br />131,072 Kib <br />16,384 KiB <br />128 Mib <br />0.0156 GiB <br /> (SPI NOR)
RAM1 Size 128 MiB 134,217,728 B <br />1,048,576 Kib <br />131,072 KiB <br />1,024 Mib <br />0.125 GiB <br /> (DDR2)
RAM1 Chip Winbond NT5TU128M8GE-AC
ETH chip1 Realtek RTL8382M
Switch Realtek RTL8382M
Ethernet Port Count 24-1GbE
Ethernet connector 8P8C
Wired Standard IEEE 802.3i/3u/3ab
Auto-MDIX supported
Jumbo frame yes
Switch Class managed

Ethernet OUI: C8:54:4B

Expansion IF types none specified
Stock bootloader U-Boot
Power 100-240 VAC ~ 50/60 Hz, 0.32 A
Connector type C13
Serial Port (UART) yes, 4-pin header, populated, JP2, 3.3V TTL, (115200 8N1)
Other

Default IP address: 192.168.1.1
the IP 192.168.1.1 is used by 1359 additional devices
of which 100 are ZyXEL devices
Default login user: admin
Default login password: 1234
admin:1234 credentials used by 191 additional devices
of which 69 are ZyXEL devices

Flags:
Smart switch, LACP, SNMP, MSTP, RSTP, metal case, heatsink, power switch
3rd Party Firmware Support OpenWrt • (List | Dev | DLs)

Additional chips
Serial GPIO/LED Display Controller;Realtek;RTL8231;;2;
5-12V, 300kHz Synchronous Buck Controller;ANPEC;APW7165;;1;
3A, 24V, 340kHz Synchronous Buck Converter;ANPEC;APW7313;;2;
30V, 30V, 18A N-Channel MOSFET;CYStech;MTB06N03Q8;;2;

Retail
Newegg N82E16833181323
ASIN B00GU1KSHS
Country of manuf China
 Switch brandSwitch2 brand
ZyXEL GS1900-10HPRealtek
ZyXEL GS1900-16Realtek
ZyXEL GS1900-24 rev A1Realtek
ZyXEL GS1900-24ERealtek
ZyXEL GS1900-24EPRealtek
ZyXEL GS1900-24HPRealtek
ZyXEL GS1900-24HP rev B1Realtek
ZyXEL GS1900-8 rev A1Realtek
ZyXEL GS1900-8 rev B1Realtek
ZyXEL GS1900-8HP rev A1Realtek
ZyXEL GS1900-8HP rev B1Realtek
ZyXEL GS1900-8HP rev B2RealtekRealtek

For a list of all currently documented Realtek chipsets with specifications, see Realtek.

For a list of all currently documented ZyXEL devices with specifications, see ZyXEL.

Overview

Web Smart L2 managed switch

"37ZY-G724DO+412 V.12" is silkscreened on board.

Specifications

  • Processor: Realtek RTL8382M Multi-Layer Managed Switch
Controller with Embedded MIPS 4KEc @500MHz
  • Flash/RAM: 16MB (SPI NOR) Flash, 128MB RAM (DDR2)
  • 24x Gigabit Ethernet ports
  • 48Gbps switching capacity

Links of Interest

Flashing

Flashing OpenWrt

Target: realtek
Subtarget: rtl838x
Package architecture: mips_4kec
Supported Since Commit
Support started version: 22.03.0
Current supported version: 25.12.1
LAN Hardware: Realtek RTL8382M
WLAN Hardware: none
Installation method(s):
GUI OEM, U-Boot TFTP + serial recovery, see git-commit
Recovery method(s):
U-Boot TFTP + serial recovery, see git-commit
git • >>
realtek: add support for ZyXEL GS1900-24E
The ZyXEL GS1900-24E is a 24 port gigabit switch similar to other GS1900
switches.

Specifications
--------------
* Device:    ZyXEL GS1900-24E
* SoC:       Realtek RTL8382M 500 MHz MIPS 4KEc
* Flash:     16 MiB Macronix MX25L12835F
* RAM:       128 MiB DDR2 SDRAM Nanya NT5TU128M8GE
* Ethernet:  24x 10/100/1000 Mbps
* LEDs:      1 PWR LED (green, not configurable)
             1 SYS LED (green, configurable)
             24 ethernet port link/activity LEDs (green, SoC controlled)
* Buttons:   1 "RESET" button on front panel
* Switch:    1 Power switch on rear of device
* Power      120-240V AC C13
* UART:      1 serial header (JP2) with populated standard pin connector on
             the left side of the PCB.
             Pinout (front to back):
             + Pin 1 - VCC marked with white dot
             + Pin 2 - RX
             + Pin 3 - TX
             + PIn 4 - GND

Serial connection parameters:  115200 8N1.

Installation
------------

OEM upgrade method:

* Log in to OEM management web interface
* Navigate to Maintenance > Firmware
* Select the HTTP radio button
* Select the Active radio button
* Use the browse button to locate the
realtek-rtl838x-zyxel_gs1900-24e-initramfs-kernel.bin
file and select open so File Path is updated with filename.
* Select the Apply button. Screen will display "Prepare
for firmware upgrade ...".
*Wait until screen shows "Do you really want to reboot?"
then select the OK button
* Once OpenWrt has booted, scp the sysupgrade image to /tmp and flash it:
   > sysupgrade -n /tmp/realtek-rtl838x-zyxel_gs1900-24e-squashfs-sysupgrade.bin
   it may be necessary to restart the network (/etc/init.d/network restart) on
   the running initramfs image.

U-Boot TFTP method:

* Configure your client with a static 192.168.1.x IP (e.g. 192.168.1.10).
* Set up a TFTP server on your client and make it serve the initramfs image.
* Connect serial, power up the switch, interrupt U-boot by hitting the
  space bar, and enable the network:
   > rtk network on
* Since the GS1900-24E is a dual-partition device, you want to keep the OEM
  firmware on the backup partition for the time being. OpenWrt can only boot
  from the first partition anyway (hardcoded in the DTS). To make sure we are
  manipulating the first partition, issue the following commands:
  > setsys bootpartition 0
  > savesys
* Download the image onto the device and boot from it:
   > tftpboot 0x84f00000 192.168.1.10:openwrt-realtek-rtl838x-zyxel_gs1900-24e-initramfs-kernel.bin
   > bootm
* Once OpenWrt has booted, scp the sysupgrade image to /tmp and flash it:
   > sysupgrade -n /tmp/openwrt-realtek-rtl838x-zyxel_gs1900-24e-squashfs-sysupgrade.bin
   it may be necessary to restart the network (/etc/init.d/network restart) on
   the running initramfs image.

Pictures

User Images