Cudy AP3000

From TechInfoDepot
Jump to navigationJump to search
multiple revisions of this device, use caution
abgn+ac+ax (AX3000)
AX3000 Ceiling Mount Wi-Fi 6 Access Point with 2.5G Port
Homepage Product page
WikiDevi.wi-cat.ru Cudy AP3000
3rd Party Firmware
dd-wrt Status Unknown
OpenWrt Status Unknown
Tomato any flavor Incompatible
Gargoyle Status Unknown
Platform
Brand • Model • Rev Cudy AP3000 (Rev1.0)
FCC ID 2APRGAP01
Type access point
CPU1 checkY MediaTek MT7981BA
CPU1 Type ARM Cortex-A53
CPU1 Speed 1.3 GHz ( 2 cores ) 64-bit
Flash1 Chip ESMT F50L2G41XA-104
Flash1 Size 256 MiB 268,435,456 B <br />2,097,152 Kib <br />262,144 KiB <br />2,048 Mib <br />0.25 GiB <br />
RAM1 Size 512 MiB 536,870,912 B <br />4,194,304 Kib <br />524,288 KiB <br />4,096 Mib <br />0.5 GiB <br />
RAM1 Chip ESMT M16U4G16256A-QLB
ETH chip1 MediaTek MT7981BA
ETH chip2 Realtek RTL8221B
Ethernet Port Count 1-2.5GbE-LAN
Wired Standard IEEE 802.3i/3u/3ab/3bz

802dot11 OUI: 80:AF:CA (15 E, 14 W)
Ethernet OUI: 80:AF:CA (15 E, 14 W)

Stock bootloader U-Boot
Stock FW OS Linux
Expansion IF types none specified
PoE 802.3at, 802.3af, standard
Power 12 VDC, 1.5 A
Connector type barrel
Serial Port (UART) yes, 4-pin header, J6, 3.3V TTL, (115200 8N1)

Flags:
Wi-Fi 6, HEW160, MU-MIMO, WPA3, Mesh, heatsink

Other

Default SSID: Cudy-AP3000
Default IP address: 192.168.10.254
the IP 192.168.10.254 is used by 6 additional devices
of which 6 are Cudy devices
Default login user: blank
Default login password: admin
blank:admin credentials used by 292 additional devices
of which 18 are Cudy devices

3rd Party Firmware Support OpenWrt • (List | Dev | DLs)
Retail
FCC approval date 22 March 2024
Country of manuf China
Radio 1
Chip1 MediaTek MT7981BA
Chip2 MediaTek MT7976CN
Wireless interface OUI 80:AF:CA
Antenna Connector Type U.FL (internal)
MIMO status 2x2:2
Wireless Standard IEEE 802.11b/g/n/ax
802.11ax up to 574 Mbps
802.11n up to 300 Mbps
802.11g up to 54 Mbps
802.11b up to 11 Mbps
WiFi Operating Frequency 2.4 GHz
Radio 2
Chip1 MediaTek MT7981BA
Chip2 MediaTek MT7976CN
Wireless interface OUI 80:AF:CA
Antenna Connector Type U.FL (internal)
MIMO status 2x3:2
Wireless Standard IEEE 802.11a/n/ac/ax
AX-QAM up to 2402 Mbps
802.11ax up to 1201 Mbps
802.11ac up to 867 Mbps
802.11n up to 300 Mbps
802.11a up to 54 Mbps
WiFi Operating Frequency 5 GHz
 CPU1 brandRadio1 chip1 brandRadio2 chip1 brand
Cudy AP3000MediaTekMediaTekMediaTek
Cudy AP3000 Outdoor v1MediaTekMediaTekMediaTek
Cudy AP3000 WallMediaTekMediaTekMediaTek

For a list of all currently documented MediaTek chipsets with specifications, see MediaTek.
For a list of all currently documented Realtek chipsets with specifications, see Realtek.

For a list of all currently documented Cudy devices with specifications, see Cudy.

• 574 Mbps - 2SS 2.4GHz 802.11ax (40MHz chan., 1024QAM),
• 2402 Mbps - 2SS 5GHz 802.11ax (160MHz chan., 1024QAM) = AX3000 class

Links of Interest

Models

Cudy AP1200 Outdoor • AC1200
Cudy AP1300 Outdoor • AC1200
Cudy AP1300 Wall • AC1200
Cudy AP1300E Wall • AC1200
Cudy AP3000 Outdoor • AX3000
Cudy AP3000 Wall • AX3000
Cudy AP3000E Wall • AX3000

Flashing

Flashing OpenWrt

Target: mediatek
Subtarget: filogic
Package architecture: aarch64_cortex-a53
Supported Since Commit
Support started version: 24.10.0
Current supported version: 25.12.5
LAN Comment: Realtek RTL8221B 2.5GbE PHY -or- Motorcomm YT8821 2.5GbE PHY
WLAN Hardware: MediaTek MT7981BA, MediaTek MT7976CN
WLAN Comment: 2.4GHz: 2x2:2 MIMO, 5GHz: 2x3:2 MIMO
Installation method(s):
GUI OEM
Install Comment:
Need a signed OpenWrt from cudy before installing official OpenWrt image
Recovery method(s):
see git-commit
Recovery Comment:
recovery only via serial
Comment:
A new variant of AP3000 v1 has been discovered with a different LAN chip Motorcomm YT8821 2.5GbE PHY. Previously, Realtek RTL8221B 2.5GbE PHY was the only LAN chip in use.
git • >>
mediatek/filogic: add support for Cudy AP3000 v1
Hardware:
  SoC:     MT7981b
  RAM:     512 MB
  Flash:   256 MB SPI NAND
  Ethernet:
    1x2.5Gbps (rtl8221b)
  WiFi:    2x2 MT7981
  Button:  Reset
  LED:     1x multicolor

Installation
------------
At the moment, firmware installation is only possible via a transition firmware.
It's can be requested from the manufacturer by email to support@cudy.com

Signed-off-by: Maxim Anisimov
Link: https://github.com/openwrt/openwrt/pull/17225
Signed-off-by: Hauke Mehrtens

See also

Cudy • List of 802.11ax Hardware
MediaTek MT7981BA/MT7976CN
MediaTek MT7981BA/MT7976CN
Cudy RE1200 Outdoor (AC1200)
MediaTek MT7981BA/MT7976CN
MediaTek MT7981BA/MT7976CN
MediaTek MT7981BA/MT7976CN
MediaTek MT7981BA/MT7976CN